NM80PKX200Smartphone

Safety and regulatory guide Safety and regulatory guide 2 Please read before proceeding THE BATTERY IS NOT FULLY CHARGED WHEN YOU TAKE THE DEVICE OUT OF THE BOX. Privacy restrictions Some countries require full disclosure of recorded telephone conversations. Pictograms and graphic symbols Read this manual’s Safety Information and General Precautions. Do not use while re-fuelling Do not use hand-held while driving This device may produce a bright or flashing light For body-worn operation maintain a separation of 1.5 cm Do not dispose of in a fire Small parts may cause a choking hazard Avoid contact with magnetic media This device may produce a loud sound Avoid extreme temperatures Keep away from pacemakers and other personal medical devices Avoid contact with liquid, keep dry Switch off when instructed in hospitals and medical facilities Do not try and disassemble Switch off when instructed in aircraft and airports Do not rely on this device for emergency communications Safety and regulatory guide 3 Switch off in explosive environments Only use approved accessories Important health information and safety precautions When using this product, the safety precautions below must be taken to avoid possible legal liabilities and damages. Retain and follow all product safety and operating instructions. Observe all warnings in the operating instructions on the product. To reduce the risk of bodily injury, electric shock, fire, and damage to the equipment, observe the following precautions. Electrical safety This product is intended for use when supplied with power from the designated battery or power supply unit. Other usage may be dangerous and will invalidate any approval given to this product. Safety precautions for proper grounding installation CAUTION: Connecting to improperly grounded equipment can result in an electric shock to your device. This product is equipped with a USB Cable for connecting with desktop or notebook computer. Be sure your computer is properly grounded (earthed) before connecting this product to the computer. The power supply cord of a desktop or notebook computer has an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet which is properly installed and grounded in accordance with all local codes and ordinances. Safety precautions for power supply unit  Use the correct external power source A product should be operated only from the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your authorized service provider or local power company. For a product that operates from battery power or other sources, refer to the operating instructions that are included with the product. This product should be operated only with the following designated power supply unit(s). Safety and regulatory guide 4 AC adapter: HTC, Model TC U250, TC E250, TC A250, TC P800-UK  Handle battery packs carefully This product contains a Lithium-ion polymer or Lithium-ion battery. There is a risk of fire and burns if the battery pack is handled improperly. Do not attempt to open or service the battery pack. Do not disassemble, crush, puncture, short external contacts or circuits, dispose of in fire or water, or expose a battery pack to temperatures higher than 60 ̊C (140 ̊F). WARNING: To reduce risk of fire or burns, do not disassemble, crush, puncture, short external contacts, expose to temperature above 60° C (140° F), or dispose of in fire or water. Recycle or dispose of used batteries according to the local regulations or reference guide supplied with your product.  Take extra precautions  Keep the device dry and away from water or any liquid as it may cause a short circuit.  The phone should only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.  If the battery leaks:  Do not allow the leaking fluid to come in contact with skin or clothing. If already in contact, flush the affected area immediately with clean water and seek medical advice.  Do not allow the leaking fluid to come in contact with eyes. If already in contact, DO NOT rub; rinse with clean water immediately and seek medical advice.  Take extra precautions to keep a leaking battery away from fire as there is a danger of ignition or explosion. Safety and regulatory guide 5 Safety precautions for direct sunlight Keep this product away from excessive moisture and extreme temperatures. Do not leave the product inside a vehicle or in places where the temperature may exceed 60°C (140°F), such as on a car dashboard, window sill, or behind a glass that is exposed to direct sunlight or strong ultraviolet light for extended periods of time. This may damage the product, overheat the battery, or pose a risk to the vehicle. Prevention of hearing loss CAUTION: Permanent hearing loss may occur if earphones or headphones are used at high volume for prolonged periods of time. This device and earphone have been tested to comply with the Sound Pressure Level requirement laid down in the applicable EN 50332-1 and/or EN 50332-2 standards. Safety in aircraft Due to the possible interference caused by this product to an aircraft’s navigation system and its communications network, using this device’s phone function on board an airplane is against the law in most countries. If you want to use this device when on board an aircraft, remember to turn off your phone by switching to Airplane Mode. Environment restrictions Do not use this product in gas stations, fuel depots, chemical plants or where blasting operations are in progress, or in potentially explosive atmospheres such as fuelling areas, fuel storehouses, below deck on boats, chemical plants, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Please be aware that sparks in such areas could cause an explosion or fire resulting i…

Text truncated - open the document above for the full version.

HTC Desire 626 User guide HTC CONFIDENTIAL for Certification only About this guide In this user guide, we use the following symbols to indicate useful and important information: This is a note. A note often gives additional information, such as what happens when you choose to do or not to do a certain action. A note also provides information that may only be applicable to some situations. This is a tip. A tip gives you an alternative way to do a particular step or procedure, or lets you know of an option that you may find helpful. This indicates important information that you need in order to accomplish a certain task or to get a feature to work properly. This provides safety precaution information, that is, information that you need to be careful about to prevent potential problems. Some apps may not be available in all regions or with your mobile operator. 1 About this guide HTC CONFIDENTIAL for Certification only Important note on recoverable data Files and other data that have been deleted, cleared, removed, or erased from your device may still be recoverable by third-party data recovery software. Even a factory reset may not permanently erase all data from your phone, including personal information. 2 Important note on recoverable data HTC CONFIDENTIAL for Certification only Features you'll enjoy Features on HTC Desire 626 HTC Desire 626 gives you options for quick and easy setup. Transferring your old phone's content such as your contacts, messages, and media can be done right from HTC Desire 626. Also, enjoy taking shots with the camera, checking personalized content with HTC BlinkFeed ™ , and more. Easy phone setup and transfer §With our HTC Get Started service, you can set up and personalize HTC Desire 626 from your computer, and just download your settings to HTC Desire 626. See Setting up your new phone for the first time on page 17. §Easily transfer your contacts, messages, music, photos, videos, and more from an Android ™ phone to HTC Desire 626. See Transferring content from an Android phone on page 19. By using HTC Sync Manager, you can even migrate content from an iPhone. See Transferring iPhone content and apps to your HTC phone on page 117. §Back up HTC Desire 626 to the cloud so it'll be a lot easier to restore your content to a new phone next time. Dynamic Home screen With HTC BlinkFeed, personalize your Home screen with the information and updates that matter most to you. See a variety of content such as feeds about news and your interests, social network updates, HTC Desire 626 tips, and more. The content refreshes periodically when you're connected to the Internet. See Your dynamic Home screen on page 46. HTC Dot View HTC Desire 626 has a dedicated HTC Dot View ™ case you can purchase. With the HTC Dot View app, you can even personalize what's seen through the case such as the wallpaper, types of notifications to display, and more. See Personalizing HTC Dot View on page 44. 3 Features you'll enjoy HTC CONFIDENTIAL for Certification only Outstanding camera features §Choose from pre-defined camera modes, or create your own. See Choosing a capture mode on page 58. §With VideoPic, you can snap a picture while you're shooting video. See Taking a photo while recording a video — VideoPic on page 62. Google Drive integration HTC Desire 626 features an additional 100GB of Google Drive ™ storage free for 2 years. See Activating your free Google Drive storage on page 105. 4 Features you'll enjoy HTC CONFIDENTIAL for Certification only Unboxing HTC Desire 626 1.Microphone and speaker 2.POWER 3.VOLUME buttons 4.Proximity sensor 5.Receiver 6.3.5mm headset jack 7.Notification LED 8.Front camera 9.Slot cover 10.USB connector You need a 4G/LTE ™ plan to use your operator's 4G/LTE network for voice calls and data services. Check with your operator for details. §If you want to use a case or screen protector, don’t cover and block the proximity sensor. Purchase a case or screen protector designed for HTC Desire 626. §Avoid connecting third-party headsets or accessories with metallic charms that dangle near the headset jack. Using these may affect signal reception. 5 Unboxing HTC CONFIDENTIAL for Certification only nano SIM card HTC Desire 626 uses a nano SIM card. Use a standard nano SIM card only. Inserting a modified card that is thicker than the standard nano SIM card may cause the card to not fit properly or damage the card slot. Inserting a nano SIM card 1.Make sure HTC Desire 626 is off and hold it securely with the front facing down. 2.Open the slot cover with your thumb or finger. 3.Pull the tray out from the nano SIM slot. 6 Unboxing HTC CONFIDENTIAL for Certification only 4.Place a nano SIM card into the tray with the card's gold contacts facing up and its cut-off corner facing out. 5.Make sure the tray is facing up. Reinsert the tray into the slot. 6.To close the slot cover, slide the plastic hinge into the side and press the cover until it clicks into place. Removing a nano SIM card Make sure to switch off HTC Desire 626 before removing the card. 1.Open the slot cover with your thumb or finger. 2.Pull the tray out from the SIM slot, and remove the nano SIM card. 3.To close the slot cover, slide the plastic hinge into the side and press the cover until it clicks into place. 7 Unboxing HTC CONFIDENTIAL for Certification only Storage card Use a storage card to store your photos, videos, and music. When you need to free up phone storage space, you can also move certain apps to the storage card, if the apps support this feature. The storage card is optional and sold separately. §Moving apps to the storage card doesn't back up the apps. If you do a factory reset, your phone loses the apps. You'll need to reinstall them. §When you remove the storage card and insert it in another phone, the apps on the storage card won't be installed automatically to the other phone. You'll need to reinstall them. Inserting the storage card 1.Open the slot cover with your thumb or finger. 2.With H…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT The EUT has following accessories. Product Brand MODEL Description Adapter 1 Salcomp TC X250 (X= A, E, I, U) I/P: 100-240Vac, 200mA O/P: 5Vdc, 1A Adapter 2 Phihong TC X250 (X= A, E, I, U) I/P: 100-240Vac, 200mA O/P: 5Vdc, 1A Battery 1 ATL B0PKX100 Rating: 3.85Vdc, 2000mAh Type: Li-ion Battery 2 BYD B0PKX100 Rating: 3.8Vdc, 2000mAh Type: Li-ion Earphone 1 SIYOTO HS S270 1m cable Earphone 2 Merry HS S250 1m cable Earphone 3 Cotron HS S250 1m cable USB Cable 1 COXOC DC MSR600 1.0m cable USB Cable 2 Foxconn DC MSR600 1.0m cable USB Cable 3 Foxlink DC MSR600 1.0m cable LCD Panel 1 Truly TDO-HD0499K70710 -- LCD Panel 2 Henghao HD-L050HD04-F5PA -- Photo Camera LITEON 4BAD62P1 -- Video Camera 1 LITEON 4BF520P1 -- Video Camera 2 LITEON 4BF810P2 -- Memory 1 HYNIX H9TQ17ABJTMCUR-KUM -- Memory 2 Samsung KMR820001M-B609 -- Page 2 <Main sample> Page 3 <2 nd sample> Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14

Page 15 <Main sample> Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 <2 nd sample> Page 31 Page 32 Page 33

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 42 Report No. : SA150520C16 R1 Issued Date : Jul. 09, 2015 Cancels and replaces the report no.: SA150520C16 dated on Jun. 30, 2015 FCC SAR Test Report Report No. : SA150520C16 R1 Applicant : HTC Corporation Address : 1F, 6-3 Baoqiang Road, Xindian District, New Taipei City, Taiwan 231 Product : Smartphone FCC ID : NM80PKX200 Brand : HTC Model No. : 0PKX200 Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a -2005 / KDB 865664 D01 v01r03 / KDB 865664 D02 v01r01 KDB 248227 D01 v02r01 / KDB 447498 D01 v05r02 / KDB 648474 D04 v01r02 KDB 941225 D01 v03 / KDB 941225 D05 v02r03 / KDB 941225 D06 v02 Sample Received Date : May 20, 2015 Date of Testing : Jun. 09, 2015 ~ Jun. 25, 2015 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Ivonne Wu / Supervisor Approved By : Gordon Lin / Assistant Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Ivonne Wu / SupervisorIvonne Wu Lin/ Assistant Manager hisre IvonneW FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 42 Report No. : SA150520C16 R1 Issued Date : Jul. 09, 2015 Cancels and replaces the report no.: SA150520C16 dated on Jun. 30, 2015 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 14 3.4 SAR Measurement Procedure ................................................................................................................................... 15 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 15 3.4.2 Volume Scan Procedure................................................................................................................................... 15 3.4.3 Power Drift Monitoring .........................…

Text truncated - open the document above for the full version.

Report No.: RF150520C16-5 1 of 57 Report Format Version 5.2.1 FCC TEST REPORT (15.247) REPORT NO.: RF150520C16-5 MODEL NO.: 0PKX200 FCC ID: NM80PKX200 RECEIVED: May 20, 2015 TESTED: Jun. 13, 2015 ~ Jun. 17, 2015 ISSUED: Jun. 30, 2015 APPLICANT: HTC Corporation ADDRESS: 1F, 6-3 Baoqiang Road, Xindian District, New Taipei City, Taiwan 231 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150520C16-5 2 of 57 Report Format Version 5.2.1 TABLE OF CONTENTS RELEASE CONTROL RECORD ..............................................................................................................4 1. CERTIFICATION ..................................................................................................................................5 2. SUMMARY OF TEST RESULTS .........................................................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................................................6 3. GENERAL INFORMATION ..................................................................................................................7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................7 3.2 DESCRIPTION OF TEST MODES ..............................................................................................8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................................9 3.3 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.4 DUTY CYCLE TEST SIGNAL ................................................................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 13 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ....................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 14 4.1.2 TEST INSTRUMENTS ................................................................................................. 15 4.1.3 TEST PROCEDURES ................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 16 4.1.5 TEST SETUP ............................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 17 4.1.7 TEST RESULTS........................................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 33 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 33 4.2.2 TEST INSTRUMENTS ................................................................................................. 33 4.2.3 TEST PROCEDURES ................................................................................................. 34 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 34 4.2.5 TEST SETUP ............................................................................................................... 35 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 35 4.2.7 TEST RESULTS........................................................................................................... 36 4.3 6dB BANDWIDTH MEASUREMENT ....................................................................................... 38 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................................ 38 4.3.2 TEST SETUP ............................................................................................................... 38 4.3.3 TEST INSTRUMENTS ........................................................…

Text truncated - open the document above for the full version.

Report No.: RF150520C16-4 1 of 38 Report Format Version 5.1.0 FCC TEST REPORT REPORT NO.: RF150520C16-4 MODEL NO.: 0PKX200 FCC ID: NM80PKX200 RECEIVED: May 20, 2015 TESTED: Jun. 13, 2015 ~ Jun. 17, 2015 ISSUED: Jun. 30, 2015 APPLICANT: HTC Corporation ADDRESS: 1F, 6-3 Baoqiang Road, Xindian District, New Taipei City, Taiwan 231 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150520C16-4 2 of 38 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..............................................................................................................4 1. CERTIFICATION ..................................................................................................................................5 2. SUMMARY OF TEST RESULTS .........................................................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................................................6 3. GENERAL INFORMATION ..................................................................................................................7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................7 3.2 DESCRIPTION OF TEST MODES ..............................................................................................8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................................9 3.3 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 12 4. TEST TYPES AND RESULTS (FOR BLUETOOTH LE 4.0) ............................................................. 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 13 4.1.2 TEST INSTRUMENTS ................................................................................................. 14 4.1.3 TEST PROCEDURES ................................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 15 4.1.5 TEST SETUP ............................................................................................................... 16 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 16 4.1.7 TEST RESULTS........................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 23 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 23 4.2.2 T EST INSTRUMENTS ................................................................................................ 23 4.2.3 TEST PROCEDURES .......…

Text truncated - open the document above for the full version.