NM82QD4100Headset

We, HTC Corporation, attest that this device under FCC ID NM82QD4100 complies with device protocol requirements and operational restrictions. This device’s transmit power spectral density is in accordance with the rules for low power indoor access points. Attestation of Indoor Client Operation (6XD) 1. The device will only associate and connect with a low-power indoor access point or subordinate device and never directly connect to other client devices. 2. This device will always initiate transmission under the control of a low power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. 3. Transmissions will be lower or equal to the power advertised by the indoor low-power access point or subordinate and never above the maximum output power allowed by the FCC grant for equipment class 6XD. 4. Control of or communications with unmanned aircraft systems, including drones are prohibited. HTC Corporation ____________________________ Signature Mandy Lin Manager (02) 8912 4138 #22398 [email protected]

U.S. Agent Designation for Serviceof Process TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTENTION: FCC Certification –Section 2.911(d)(7) Information Designated U.S. Agent Company Name:HTC America, Inc. Contact Name:Marc Metis Street Address:1625 Shattuck Ave., 3d Floor City/Province/Zip:Berkeley, CA 94709 Telephone No:510903-5999 Email:[email protected] FRN #: 0018941682 This letter is to confirm that we(“the Designated U.S. Agent”)have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: Signed by (Printed Name/Title): Marc Metis, Vice President, HTC America, Inc. The Applicantacknowledgesththat they must maintain an agentfor no less than one year after terminatingall marketing and importation ORORthe conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges theirresponsibility to inform the FCC whenever the Designated U.S. Agent informationabovechanges. Applicant Company name: HTC Corporation Grantee Code: NM8 Contact Name: Sylvia Shen Street Address: No. 88, Section 3, Zhongxing Road, Xindian District City/Province/Zip: New Taipei City, Taiwan Telephone No: +886 2 8912 4138 Email: [email protected] FRN #:0018127647 Applicant Signature: Date: Signed by (Printed Name/Title): Sylvia Shen,Sr. Manager, HTC Corporation

Rev 1/26/2023 Page 1 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 3/28/2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: NM82QD4100 [HTC Corporation] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Mandy Lin Manager (02) 8912 4138 #22398 [email protected] Rev 1/26/2023 Page 2 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 3/28/2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: NM82QD4100 [HTC Corporation] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Mandy Lin Manager (02) 8912 4138 #22398 [email protected]

Page 1 of 1 The Grantee will need to provide the TCB with a letter on the company letterhead requesting a Grant Deferral. The grant deferral should include the following: 1. FCC ID: NM82QD4100 and IC: 4115A-2QD4100 2. Date of requested Grant and/or REL release issue date and if applicable the time. 3. Signed by the authorized person listed with the FCC and ISED Canada of said company. 4. If a scheduled meeting is required on the day and time of the scheduled release date/time of the grant/REL listing. The client shall notify the TCB of any changes to the requested date and time of the requested submittal by sending a letter signed by the authorized representative to the TCB Certifier and copy email address Timco Certification <cb@industrial- ia.com> . If needed, the TCB can schedule a meeting during the scheduled day/time the grant is to be released. Example Grant Deferral: To TUV Rheinland TCB/FCB, We are requesting a Grant Deferral and delayed REL release as noted below. (all information required) Company Name: HTC Corporation FCC Grant Deferral Information FCC ID: NM82QD4100 Deferral Date:__2024.09.30_____________ Deferral Time (Leave Blank if Not Applicable):____________________ ISED Canada Deferral Information IC: 4115A-2QD4100 Deferral Date:___ 2024.09.30_____________ Deferral Time (Leave Blank if Not Applicable):____________________ (Select the appropriate box below). ☒ Prior to release of the certification, we request to have a meeting with the TCB Certifier on the day that the grant is scheduled be released on the FCC and ISED Canada website to re-confirm the timing of the certificate release with us. (Note – by selecting this service, the certification will not be automatically set for release but will remain in draft form until the TCB has final confirmation for release) ☐ We do not require a reconfirmation meeting before the scheduled release (Note - by selecting this service, the certification will be automatically released on the preselected date). Any date changes to the Grant and REL listing are required to be communicated to TUV Rheinland by resubmittal of this application 48 hours prior to the scheduled release to insure adequate time to make required changes. Signature: _____________________ Printed Name of Authorized Representative: Mandy Lin Title: Manager Date:2024-03-28

Date: 2024/4/8 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Product Certification Representative Authorization Letter FCC ID: NM82QD4110 Product name: Headset To whom it may concern: I, Sylvia Shen, the undersigned, hereby authorize the person named below to act on my behalf as authorized agent and representative for this project. All acts carried out and requests made by this named representative relating to any matter before the FCC, including requests for confidentiality, shall have the same effect as mine. HTC Corporation Address : No. 88, Section 3, Zhongxing Road, Xindian District, New Taipei City 231, Taiwan Name : Mandy Lin e-mail : [email protected] I declare under penalty of perjury that the foregoing is true and correct, and that this Authorization was executed at USA on the date indicated below my signature. Applicant : HTC Corporation Address : No. 88, Section 3, Zhongxing Road, Xindian District, New Taipei City 231, Taiwan Signature : _________________________________ Name and Job Title. : Sylvia Shen, Sr. Manager E-mail : [email protected] Tel. : 886289124138

Page 1 of 1 Authority to Act as Agent Date: 11 April 2024 Timco Engineering, Inc. 13146 NW 86th Drive Suite 400 Alachua, FL 32615 To Whom It May Concern: I appoint TÜ V Rheinland Taiwan Ltd., Ivan Hsieh to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canada’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with HTC Corporation, No. 88, Sec. 3, Zhongxing Rd. Xindian Dist., New Taipei City 231, Taiwan For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Date: 2024/4/11 Agreement is valid for 12 months from the above date. By: __________________________ Mandy Lin (Signature) (Print name) Manager (02) 8912 4138 #22398 (Title) (Telephone) On behalf of: HTC Corporation (Company Name)

MS-0044715 Page 1 of 1 Revision 1 Date: 4/11/2024 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Confidentiality Request for FCC ID: NM82QD4100 Pursuant to FCC 47 CRF 0.457(d), the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term Permanent External Photo Short Term Permanent Internal Photos *** Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Schematics Short Term Permanent Test Setup*** Short Term Permanent Tune-Up Procedure Short Term Permanent User’s Manual*** Short Term Permanent Software Security Information HTC Corporation has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. (*** Exceptional case for Permanent Confidentiality for these Exhibits by PAG only) Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of specify number of days not to exceed 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By: _______________________________________________ Mandy Lin (Signature/Title) (Print name) Tel: (02) 8912 4138 #22398 Email: [email protected]

2QD4100 E-Label information 1. Images of the e-label screen are provided below: Information On E‐label In User Manual FCC ID/IC number V V DoC logo V Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device V Class A / B Digital Device user manual statements V 1. Users are able to access the information in no more than 3 steps in a device’s menu. 2. The actual Steps are: select Settings > About > Regulatory information The E-Label can be accessed without any special accessories, access codes, or SIM card having to be in place. 3. Electronic labeling information is programmed into the device by the manufacturer at the time of manufacture. 4. Electronic labeling information is not modifiable by any third party.

Prüfbericht - Produkte Test Report - Products Prü fbericht-Nr.: Test report no.: CN24CB9V 001 Auftrags-Nr.: Order no.: 48244361 Seite 1 von 47 Page 1 of 47 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 2024-02-27 Auftraggeber: Client: HTC Corporation No. 88, Sec. 3, Zhongxing Rd. Xindian Dist., New Taipei City 231, Taiwan Prü fgegenstand: Test item: Headset Bezeichnung / Typ-Nr.: Identification / Type no.: 2QD4100 Auftrags-Inhalt: Order content: Test Report for RF Exposure Evaluation Prü fgrundlage: Test specification: FCC 47CFR Part 2(2.1093) IEC TR 63170 IEC/IEEE 63195-1 IEC/IEEE 62209-1528:2020 Wareneingangsdatum: Date of sample receipt: 2024-03-13 Prü fmuster-Nr.: Test sample no: A003674863-007 Prü fzeitraum: Testing period: 2024-03-20 - 2024-04-13 Ort der Prü fung: Place of testing: EMC/RF Taipei Testing Site Prü flaboratorium: Testing laboratory: Taipei Testing Laboratories Prü fergebnis*: Test result*: Pass ü berprü ft von: compiled by: Morrison Huang genehmigt von: authorized by: Brenda Chen Datum: Date: 2024-04-26 Ausstellungsdatum: Issue date: 2024-04-26 Stellung / Position: Project Engineer Stellung / Position: Senior Project Manager Sonstiges / Other: Zustand des Prü fgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prü fbericht bezieht sich nur auf das o.g. Prü fmuster und darf ohne Genehmigung der Prü fstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prü fzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TUV Rheinland Taiwan Ltd. 11F., No. 758, Sec. 4, Bade Rd., Taipei 105, Taiwan, R.O.C. Mail: [email protected] ∙ Web: www.tuv.com V101023GCNSR Prüfbericht - Produkte Test Report - Products Prüfbericht-Nr.: Test report no.: CN24CB9V 001 Seite 2 von 47 Page 2 of 47 Anmerkungen Remarks 1 Alle eingesetzten Prüfmittel waren zum angegebenen Prüfzeitraum gemäß eines festgelegten Kalibrierungsprogramms unseres Prüfhauses kalibriert. Sie entsprechen den in den Prüfprogrammen hinterlegten Anforderungen. Die Rückverfolgbarkeit der eingesetzten Prüfmittel ist durch die Einhaltung der Regelungen unseres Managementsystems gegeben. Detaillierte Informationen bezüglich Prüfkonditionen, Prüfequipment und Messunsicherheiten sind im Prüflabor vorhanden und können auf Wunsch bereitgestellt werden. The equipment used during the specified testing period was calibrated according to our test laboratory calibration program. The equipment fulfils the requirements included in the relevant standards. The traceability of the test equipment used is ensured by compliance with the regulations of our management system. Detailed information regarding test conditions, equipment and measurement uncertainty is available in the test laboratory and could be provided on request. 2 Wie vertraglich vereinbart, wurde dieses Dokument nur digital unterzeichnet. Der TÜ V Rheinland hat nicht überprüft, welche rechtlichen oder sonstigen diesbezüglichen Anforderungen für dieses Dokument gelten. Diese Ü berprüfung liegt in der Verantwortung des Benutzers dieses Dokuments. Auf Verlangen des Kunden kann der TÜ V Rheinland die Gültigkeit der digitalen Signatur durch ein gesondertes Dokument bestätigen. Diese Anfrage ist an unseren Vertrieb zu richten. Eine Umweltgebühr für einen solchen zusätzlichen Service wird erhoben. Informationen zur Verifizierung der Authentizität unserer Dokumente erhalten Sie auf folgender Webseite: go.tuv.com/digital-signature As contractually agreed, this document has been signed digitally only. TUV Rheinland has not verified and unable to verify which legal or other pertaining requirements are applicable for this document. Such verification is within the responsibility of the user of this document. Upon request by its client, TUV Rheinland can confirm the validity of the digital signature by a separate document. Such request shall be addressed to our Sales department. An environmental fee for such additional service will be charged. For information on verifying the authenticity of our documents, please visit the following website: go.tuv.com/digital-signature 3 Prüfklausel mit der Note * wurden an qualifizierte Unterauftragnehmer vergeben und sind unter der jeweiligen Prüfklausel des Berichts beschrieben. Abweichungen von Prüfspezifikation(en) oder Kundenanforderungen sind in der jeweiligen Prüfklausel im Bericht aufgeführt. Test clauses with remark of * are subcontracted to qualified subcontractors and descripted under the respective test clause in the report. Deviations of testing specification(s) or customer requirements are listed in specific test clause in the report. 4 Die Entscheidungsregel für Konformitätserklärungen basierend auf numerischen Messergebnisen in diesem Prüfbericht basiert auf der "Null-Grenzwert-Regel" und der "Einfachen Akzeptanz" gemäß ILAC G8:2019 und IEC Guide 115:2021, es sei denn, in der auf Seite 1 dieses Berichts genannten angewandten Norm ist etwas anderes festgelegt oder vom Kunden gewünscht. Dies bedeutet, dass die Messunsicherheit nicht berücksichtigt wird und daher auch nicht im Prüfbericht angegeben wird. Zu weiteren Informationen bezueglich des Risikos durch diese Entscheidungsregel siehe ILAC G8:2019. The decision rule for statements of conformity, based on numerical measurement results, in this test repor…

Text truncated - open the document above for the full version.

Appendix C - Cailbration Certificate

Test Laboratory: TUV Inc. Date: 2024/3/20 05_WLAN2.4GHz_802.11b 1Mbps_Rear Face_0mm_Ch6_Ant 1 DUT: HTC_2QD4100 Communication System: WLAN; Frequency: 2437 MHz; Duty Cycle: 1:1.019 Medium: HSL2450_240320 Medium parameters used: f = 2437 MHz; σ = 1.842 S/m; ε r = 40.439; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C; Liquid Temperature：22.7 °C DASY Configuration: Electronics: DAE4 Sn855; Calibrated: 2023/4/25 Probe: EX3DV4 - SN7400; ConvF(7.69, 7.69, 7.69) @ 2437 MHz; Calibrated: 2023/4/28 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -59.0, 31.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Area Scan (12x19x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.450 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 13.53 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 0.619 W/kg SAR(1 g) = 0.327 W/kg; SAR(10 g) = 0.171 W/kg Maximum value of SAR (measured) = 0.509 W/kg 0 dB = 0.509 W/kg = -2.93 dBW/kg Appendix B - SAR Measurement Test Laboratory: TUV Inc. Date: 2024/4/13 19_WLAN5GHz_802.11ac-VHT80 MCS0_Rear Face_0mm_Ch58_Ant 1 DUT: HTC_2QD4100 Communication System: WLAN; Frequency: 5290 MHz; Duty Cycle: 1:1.008 Medium: HSL5G_240413 Medium parameters used: f = 5290 MHz; σ = 4.702 S/m; ε r = 36.713; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.6 °C DASY Configuration: Electronics: DAE4 Sn917; Calibrated: 2024/3/11 Probe: EX3DV4 - SN3804; ConvF(4.44, 4.44, 4.44) @ 5290 MHz; Calibrated: 2023/5/19 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -59.0, 24.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Area Scan (16x22x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 0.489 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 5.430 V/m; Power Drift = 0.11 dB Peak SAR (extrapolated) = 1.13 W/kg SAR(1 g) = 0.378 W/kg; SAR(10 g) = 0.188 W/kg Maximum value of SAR (measured) = 0.735 W/kg 0 dB = 0.735 W/kg = -1.34 dBW/kg Test Laboratory: TUV Inc. Date: 2024/4/13 23_WLAN5GHz_802.11ac-VHT80 MCS0_Rear Face_0mm_Ch122_Ant 1 DUT: HTC_2QD4100 Communication System: WLAN; Frequency: 5610 MHz; Duty Cycle: 1:1.008 Medium: HSL5G_240413 Medium parameters used: f = 5610 MHz; σ = 5.057 S/m; ε r = 36.278; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.6 °C DASY Configuration: Electronics: DAE4 Sn917; Calibrated: 2024/3/11 Probe: EX3DV4 - SN3804; ConvF(4.17, 4.17, 4.17) @ 5610 MHz; Calibrated: 2023/5/19 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -59.0, 24.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Area Scan (16x22x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 0.905 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 7.681 V/m; Power Drift = -0.16 dB Peak SAR (extrapolated) = 1.63 W/kg SAR(1 g) = 0.493 W/kg; SAR(10 g) = 0.216 W/kg Maximum value of SAR (measured) = 1.04 W/kg 0 dB = 1.04 W/kg = 0.17 dBW/kg Test Laboratory: TUV Inc. Date: 2024/4/13 22_WLAN5GHz_802.11n-HT40 MCS0_Rear Face_0mm_Ch151_Ant 1 DUT: HTC_2QD4100 Communication System: WLAN; Frequency: 5755 MHz; Duty Cycle: 1:1.004 Medium: HSL5G_240413 Medium parameters used: f = 5755 MHz; σ = 5.213 S/m; ε r = 36.084; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.6 °C DASY Configuration: Electronics: DAE4 Sn917; Calibrated: 2024/3/11 Probe: EX3DV4 - SN3804; ConvF(4.34, 4.34, 4.34) @ 5755 MHz; Calibrated: 2023/5/19 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -59.0, 24.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Area Scan (16x22x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 0.691 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 7.906 V/m; Power Drift = 0.18 dB Peak SAR (extrapolated) = 1.48 W/kg SAR(1 g) = 0.435 W/kg; SAR(10 g) = 0.213 W/kg Maximum value of SAR (measured) = 0.905 W/kg 0 dB = 0.905 W/kg = -0.43 dBW/kg Test Laboratory: TUV International Inc. 02.WLAN6GHz_802.11ax-HE160 MCS0_Rear Face_0mm_Ch111_Ant1 Model, Manufacturer Dimensions [mm] IMEI DUT Type Device 195.0 x 90.0 x 80.0 Phone Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL Rear Face, 0.00 U-NII-6 WLAN, 10062-CAE 6505.000, 111 5.3 6.15 33.7 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V4.0 (30deg probe tilt) - 1467 HSL6500_20240401 , -- EX3DV4 - SN7400, 2023-04-28 DAE4 Sn855, 2023-04-25 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 136.0 x 238.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 8.5 x 8.5 3.4 x 3.4 x 1.4 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.4 MAIA Y Y Surface Detection All points All points Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-03-27, 12:02 2024-03-27, 12:29 psSAR1g [W/kg] 0.377 0.406 psSAR10g [W/kg] 0.151 0.167 Power Drift [dB] -0.08 0.09 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 53.0 Dist 3dB Peak [mm] 9.5 Test Laboratory: TUV Inc. Date: 2024/3/20 12_Bluetooth_1Mbps_Rear Face_0mm_Ch78_Ant 0 DUT: HTC_2QD4100 Communication System: Bluetooth; Frequency: 2480 MHz; Duty Cycle: 1:1.305 Medium: HSL2450_240320 Medium parameters used: f = 2480 MHz; σ = 1.881 S/m; ε r = 40.322; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.9 °C DASY Configuration: Electronics: DAE4 Sn855; Calibrated: 2023/4/25 Probe: EX3DV4 - SN7400; ConvF(7.69, 7.69, 7.69) @ 2480 MHz; Ca…

Text truncated - open the document above for the full version.

Test Laboratory: TUV Inc. Date: 2024/3/20 System Check_HSL2450MHz DUT: D2450V2 - SN735 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium: HSL2450_240320 Medium parameters used (interpolated): f = 2450 MHz; σ = 1.855 S/m; ε r = 40.418; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C; Liquid Temperature：22.1 °C DASY Configuration: Electronics: DAE4 Sn855; Calibrated: 2023/4/25 Probe: EX3DV4 - SN7400; ConvF(7.69, 7.69, 7.69) @ 2450 MHz; Calibrated: 2023/4/28 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -9.0, 31.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Pin=250mW/Area Scan (8x8x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 17.7 W/kg Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 103.7 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 27.6 W/kg SAR(1 g) = 13.2 W/kg; SAR(10 g) = 6.17 W/kg Maximum value of SAR (measured) = 22.1 W/kg 0 dB = 22.1 W/kg = 13.44 dBW/kg Appendix A - System Verification Test Laboratory: TUV Inc. Date: 2024/4/13 System Check_HSL5250MHz DUT: D5GHzV2 - SN1145 Communication System: CW; Frequency: 5250 MHz; Duty Cycle: 1:1 Medium: HSL5G_240413 Medium parameters used: f = 5250 MHz; σ = 4.678 S/m; ε r = 36.711; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.6 °C DASY Configuration: Electronics: DAE4 Sn917; Calibrated: 2024/3/11 Probe: EX3DV4 - SN3804; ConvF(4.44, 4.44, 4.44) @ 5250 MHz; Calibrated: 2023/5/19 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -9.0, 23.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Pin=100mW/Area Scan (9x9x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 17.6 W/kg Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.68 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 29.8 W/kg SAR(1 g) = 7.52 W/kg; SAR(10 g) = 2.19 W/kg Maximum value of SAR (measured) = 19.0 W/kg 0 dB = 19.0 W/kg = 12.79 dBW/kg Test Laboratory: TUV Inc. Date: 2024/4/13 System Check_HSL5600MHz DUT: D5GHzV2 - SN1145 Communication System: CW; Frequency: 5600 MHz; Duty Cycle: 1:1 Medium: HSL5G_240413 Medium parameters used: f = 5600 MHz; σ = 5.045 S/m; ε r = 36.26; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.6 °C DASY Configuration: Electronics: DAE4 Sn917; Calibrated: 2024/3/11 Probe: EX3DV4 - SN3804; ConvF(4.17, 4.17, 4.17) @ 5600 MHz; Calibrated: 2023/5/19 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -9.0, 23.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Pin=100mW/Area Scan (9x9x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 18.7 W/kg Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.31 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 32.1 W/kg SAR(1 g) = 8.08 W/kg; SAR(10 g) = 2.34 W/kg Maximum value of SAR (measured) = 20.4 W/kg 0 dB = 20.4 W/kg = 13.10 dBW/kg Test Laboratory: TUV Inc. Date: 2024/4/13 System Check_HSL5750MHz DUT: D5GHzV2 - SN1145 Communication System: CW; Frequency: 5750 MHz; Duty Cycle: 1:1 Medium: HSL5G_240413 Medium parameters used: f = 5750 MHz; σ = 5.208 S/m; ε r = 36.094; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.6 °C DASY Configuration: Electronics: DAE4 Sn917; Calibrated: 2024/3/11 Probe: EX3DV4 - SN3804; ConvF(4.34, 4.34, 4.34) @ 5750 MHz; Calibrated: 2023/5/19 Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = -9.0, 23.0 Phantom: Right_Twin-SAM V4.0 (20deg probe tilt); Type: QD 000 P40 CC; Serial: TP-1467 DASY52 52.10.4(1535); SEMCAD X 14.6.14(7501) Pin=100mW/Area Scan (9x9x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 18.4 W/kg Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 57.52 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 33.9 W/kg SAR(1 g) = 7.54 W/kg; SAR(10 g) = 2.16 W/kg Maximum value of SAR (measured) = 19.6 W/kg 0 dB = 19.6 W/kg = 12.92 dBW/kg Test Laboratory: TUV International Inc. System Check_HSL6500_20240401 Model, Manufacturer Dimensions [mm] IMEI DUT Type DeviceD6.5GHzV2 N/AN/AN/A x x , 16.0 x 6.0 x 300.0 SN: 1044 Phone, Dipole Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL 5, CW, 0-- 6500.000, 0 5.3 5.54 30.8 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V4.0 (30deg probe tilt) - 1467 HSL6500_20240401 , -- EX3DV4 - SN7400, 2023-04-28 DAE4 Sn855, 2023-04-25 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 51.0 x 85.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 8.5 x 8.5 3.4 x 3.4 x 1.4 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.4 MAIA N/A N/A Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-04-01, 11:50 2024-04-01, 12:07 psSAR1g [W/kg] 23.9 27.9 psSAR10g [W/kg] 4.62 5.14 Power Drift [dB] -0.00 0.02 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 49.8 Dist 3dB Peak [mm] 4.8 Test Laboratory: TUV International Inc. Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device ,10GHz 100.0 x 100.0 x 100.0 SN: 2013 Phone ,Verification Source Exposure Conditions Phantom Section Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor 5G Air FRONT, 10.00 Validation band CW, 0-- 10000.0, 10000 1.…

Text truncated - open the document above for the full version.