NMT-PE128BLE Activity and Sleep Monitor

Nautilus, Inc., (800) NAUTILUS / (800) 628-8458, www.NautilusInc.com - Customer Service: North America (800) 605-3369, [email protected] | outside U.S. +01-360-859-5180, [email protected] | Printed in China | © 2013 Nautilus, Inc. 8002754.081513.E For additional information, including Warranty, go to www.BowflexBoost.com Charging Sleep or Awake Mode / Sync This product, its packaging, and components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is provided in accordance with California’s Proposition 65. If you would like additional information, please refer to our web site at www.nautilus.com/prop65. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Quick Start Guide 1. Download the App, “ Bowflex Boost ”, available on the iPhone ® App Store. 2. Set a Goal. 3. Wear the Bowflex Boost ™ . ™ Press and hold for 2 seconds: - from solid red LED to purple, now in Sleep mode. - solid purple and two purple flashes, now in Awake mode. Press and hold for 5 seconds: - from red to purple and two purple flashes, syncing. Nautilus, Inc., (800) NAUTILUS / (800) 628-8458, www.NautilusInc.com - Service clientèle : Amérique du Nord (800) 605-3369, [email protected] | à l’extérieur des É.-U. +01-360-859-5180, [email protected] | Imprimé en Chine | © 2013 Nautilus, Inc. En charge Mode Désactivé ou Activé/Sync Ce produit, son emballage et ses composants contiennent des produits chimiques reconnus dans l’État de la Californie comme étant cancérigènes, provoquant des malformations congénitales ou pouvant affecter la fertilité. Cet avertissement est fourni en accord avec la Proposition 65 de Californie. Si vous avez des questions ou désirez des informations complé- mentaires, veuillez vous reporter à notre site Web à l’adresse www.nautilus.com/prop65. L’appareil d’alimentation répondent aux normes de la section 15 des règlements de la FCC (Federal Communication Commission). Son utilisation est soumise aux deux conditions suivantes : (1) Il ne doit pas causer d’interférences nuisibles, et (2) il doit supporter toutes les interférences reçues, y compris celles susceptibles de perturber son bon fonctionnement. Des changements ou des modifications à cette unité qui ne sont pas expressément approuvés par la partie responsable de la conformité pourraient annuler le pouvoir de l'utilisateur à faire fonctionner cet équipement. Cet appareil a été testé et déclaré conforme aux limites des appareils numériques de Classe B, selon la section 15 des règlements de la FCC (Federal Communication Commission). Ces limites sont conçues pour assurer une protection raisonnable contre les interférences nuisibles lorsque l'appareil est utilisé dans un milieu résidentiel. Cet appareil génère, utilise et peut diffuser de l'énergie radiofréquence et, s'il n'est pas installé et utilisé conformément au mode d'emploi, il peut causer des interférences aux communications radio. Il n'y a aucune garantie que des interférences ne se produiront pas dans un milieu particulier. Si cet appareil cause des interférences nuisibles aux communications radio ou télévision, ce qui peut être confirmé en l’éteignant puis en le rallumant, l'utilisateur peut tenter de corriger le problème en essayant une ou plusieurs des méthodes suivantes : • réorienter l’antenne réceptrice ou la placer à un autre endroit; • éloigner davantage l’appareil du récepteur; • brancher l'appareil dans une prise sur un circuit différent de celui sur lequel le récepteur est branché. • communiquer avec le détaillant ou un technicien radio/TV. Guide d’instruction rapide 1. Télécharger l’aplication “ Bowflex Boost ”, disponible sur iTune ® . 2. Déterminer un objectif. 3. Porter le Bowflex Boost ™ . Appuyez et maintenez le bouton enfoncé pendant deux secondes : - passer du témoin DEL rouge à pourpre, maintenant en Mode veille. - passer du témoin couleur pourpre à deux clignotements pourpre, maintenant en Mode actif. Appuyez et maintenez le bouton enfoncé pendant cinq secondes : - passer du témoin rouge à pourpre puis à deux clignotements pourpre, synchronisation. Pour plus d’information, incluant la Garantie, consulter le site www.BowflexBoost.com

iDT Technology Limited

IDT Technology Limited Request for Supersedence TO: Federal Communication Commission Please kindly be notified that we, IDT Technology Limited herein request to supersede the FCC ID: NMT-PE128 for the following reason: The battery current in the report and the product name in 731 form are incorrect. So we need to update the battery current in the report and product name in 731 form, and the report no. was updated for quality purpose. Please kindly permit the supersedence. Thank you. By: ___ Alex Chan __ (Signature/Title) (Print name) Title: Engineering Manager__________ On behalf of: IDT Technology Limited (Company Name) Telephone: _(86)2970 1028_

1 Photographs - EUT Constructional Details Test Model No.: PE128

REV12013-11-04 LIUNIN P/N: 270112522-110XX-10 (A) REV1 1/1

1 Photographs - EUT Constructional Details Test Model No.: PE128

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130900534605 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1309005346RF Applicant: IDT Technology Limited Manufacturer: iDT Technology Limited Factory: iDT Technology Limited Product Name: BLE Activity and sleep monitor Model No.(EUT): PE128 Add Model No.: PE126 FCC ID: NMT-PE128 Standards: 47 CFR Part 1.1307(2012) 47 CFR Part 2.1093 (2012) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2013-09-26 Date of Test: 2013-09-30 to 2013-10-09 Date of Issue: 2013-11-20 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above This report supersedes our previous report SZEM130900534602, issued on 2013-11-12, which is hereby deemed null and void. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM130900534605 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE ........................................................................................................................................ 1 2 CONTENTS ............................................................................................................................................ 2 3 GENERAL INFORMATION ..................................................................................................................... 3 3.1 CLIENT INFORMATION ............................................................................................................................. 3 3.2 GENERAL DESCRIPTION OF EUT ............................................................................................................. 3 3.3 TEST LOCATION .................................................................................................................................... 4 3.4 TEST FACILITY....................................................................................................................................... 4 3.5 DEVIATION FROM STANDARDS ................................................................................................................. 5 3.6 ABNORMALITIES FROM STANDARD CONDITIONS......................................................................................... 5 3.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER .............................................................................. 5 4 SAR EVALUATION ........................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130900534604 Page: 1 of 46 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1309005346RF Applicant: IDT Technology Limited Manufacturer: iDT Technology Limited Factory: iDT Technology Limited Product Name: BLE Activity and sleep monitor Model No.(EUT): PE128 Add Model No.: PE126 FCC ID: NMT-PE128 Standards: 47 CFR Part 15, Subpart C (2012) Date of Receipt: 2013-09-26 Date of Test: 2013-09-30 to 2013-10-09 Date of Issue: 2013-11-20 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. This report supersedes our previous report SZEM130900534601, issued on 2013-11-05, which is hereby deemed null and void. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM130900534604 Page: 2 of 46 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C Section 15.207 ANSI C63.10 2009 PASS Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(3) KDB558074 D01 PASS 6dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(2) KDB558074 D01 PASS Power Spectral Density 47 CFR Part 15, Subpart C Section 15.247 (e) KDB558074 D01 PASS Pseudorandom Frequency Hopping Sequence 47 CFR Part 15, Subpart C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2009) PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 PASS Radiated Spurious Emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 2009 PASS Band Edge (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 2009 PASS Remark: Model No.: PE126, PE128 Only the model PE128 was tested, since the electrical circuit design, layout, components used and internal wiring were identical for the above models, with difference being model name, color and strap. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM130900534604 Page: 3 of 46 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electroni…

Text truncated - open the document above for the full version.