NMTPE2892nd generation activity and sleep monitor wrist device

Dynamo 2 24/7 Activity Tracker Model: PE288 Quick Start Guide EN OVERVIEW Dynamo 2 Body NumberDesciption 1Operation button • Press to check unread messages. • Press and hold to start/end sleep mode or Locator. 2Snap buttonholes 3Display screen 4Buckle 5Smart core USB Charger (AD288) ChARGING AND INDICATORS After unpacking, charge the Dynamo 2 for at least 1 hour before use. Align the two metal connection points of the charger with the pair on the smart core. Make sure the curved part of the smart core and the charging pod align to each other. Push the smart core into the charger gently. You will hear a click when it is securely in the pod. Plug the large end of the USB charger into USB port of your PC. Once the smart core is correctly connected with the charger, the indicator light will turn on. GET STARTED WEAR Insert the smart core into the strap. Align the button side of both strap and the smart core before inserting into the band. Align the clasp and give it a squeeze between your thumb and index finger to fasten the strap. DOWNlOAD ThE APP Dynamo 2 tracks your activity in the day and your sleeping status at night. The data tracked transfers to your mobile device. Please pair the Dynamo 2 with your mobile before use. Download Ssmart fit application ( ) is available in Apple App Store and Google Play Store. Search ‘Ssmart fit’ as the key words. Visit the official website of your activity tracker through http://ssmart.oregonscientific.com/dynamo2/. CONNECT TO yOUR MOBIlE DEVICE Make sure your Dynamo 2 is charged for at least 1 hour before pairing. 1. Remove your Dynamo 2 from the USB power supply. The smart core displays . NOTE The smart core displays and is available for pairing up to 1 minute. After 1 minute, the smart core switches off. Repeat step 1 to make it available for pairing again. 2. Activate Bluetooth of your smart phone. For the first use, follow the instructions in the Ssmart fit app. 3. You can pair the Dynamo 2 in Ssmart fit app > Setting > Device > Setup new device. 4. During pairing, the smart core displays and vibrates. The smart core displays PAIRED and vibrates when it is successfully connected to your mobile device. 5. You can see the serial number on Device section in Settings menu. 6. The home screen shows Connected when the syncing is successful. SETTINGS Tap . You can make changes to the following items in Settings: • User Profile • Home screen • Device • Activity targets • Wake up time ACTIVITy MODE Set up your Activity Target before activity. Monitor as you go along. Tap an icon on the home screen. The screen automatically moves upwards, showing the collected data and percentage bar under each item. Dynamo 2 Indicatore di attività24/7 Modello: PE288 Guida rapida IT OVERVIEW Corpo di Dynamo 2 1 23 54 NumeroDescrizione 1Pulsante di operazione • Premere per controllare I messaggi non letti. • Premere e tenere premuto per iniziare/ terminare la modalità di riposo o il localizzatore. 2Asole a scatto 3Visualizzazione dello schermo 4Chiusura 5Nucleo trasmittente CaricatoreUSB (AD288) CARICA E INDICATORI Dopo aver rimosso l’imballo, caricare Dynamo 2 per almeno 1 ora prima dell’uso. Allineare i duepunti di connessionemetallici delcaricatore conil paiosul nucleotrasmittente. Assicurarsi che la parte curvata del nucleo trasmittente ela capsula di carico siano allineati tra loro. Spingere delicatamente ilnucleotrasmittentenel caricatore.Si sentiràun clic quandoèsaldamentenella capsula. Collegare l'estremità più grande del caricatoreUSBnella porta USBdel vostro PC. Una volta cheil nucleotrasmittentesia correttamentecollegatocon ilcaricabatterie, la spiasi accende. PER INIzIARE INDOSSARE Inserire ilnucleotrasmittentenel cinturino. Allineare illato del tastodientrambicinturinoe il nucleotrasmittenteprima di inserirenel cinturino. Allinearela chiusurae dareuna strettatra ilpollice e l'indiceper fissareil cinturino. SCARICARE l’APP Dynamo 2 tracciala vostra attivitàdurante il giorno elo stato disonnodurante la notte. I dati traccati vengono trasferiti sul vostro dispositivo mobile . Appaiare Dynamo 2 con il proprio cellulare prima dell’uso. Scaricare l’applicazione‘Ssmart fit’ ( ) è disponibile nello Store Apple App e Store di Google Play.Cercare‘Ssmart fit’come parola chiave. Visitare il sito ufficiale delle properie attivitàtracciateattraverso http://ssmart.oregonscientific.com/dynamo2/. CONNETTERSI Al PROPRIO DISPOSITIVO MOBIlE Assicurarsi cge il proprio Dynamo 2 sia caricato almeno un’ora prima dell’appaiamento. 1. Rimuovere il proprio Dynamo 2 dalla presa USB.Il nucleo trasmittente mostra . NOTA Il nucleo trasmittente mostra ed è disponibile per l’appaiamento per un 1 minuto. Dopo 1 minuto, il nucleo trasmittente si spegne. Ripetere la fase 1 per renderlo nuovamente disponibile per l’appaiamento. 2. Attivare il Bluetooth del proprio smart phone. Per il primo utilizzo, seguire le istruzioni nell’app Ssmart fit. 3. E’ possibile appaiare Dynamo 2 nell’appSsmart fit>Impostaz ioni>Dispositivo>Impostare nuovo dispositivo. 4. Durante l’appaiamento,il nucleo trasmittente mostra e vibra. Il nucleo trasmittente mostra APPAITO e vibra quando è connesso al proprio dispositivo mobile. 5. E possibile visualizzare il numero di serie nella sezione Dispositivo nel menu Impostazioni. 6. Lo schermo home mostra Conness oquando la sincronizzazione è avvenuta. IMPOSTAzIONI Selezionare . E’ possibile apportare delle modifiche ai seguenti punti in Impostazioni: • Profiloutente • Schermata Home • Dispositivo • Obiettivi di attività • Orariodellasveglia MODAlITA’ DI ATTIVITA’ Impostare il proprio Obiettivo di Attività prima dell’attività.Monitorare durante l’andamento. Selezionare un’iconasulla schermata home. Lo schermosi sposta automaticamenteverso l’alto, mostrando idati raccolti ela barra dipercentualesotto ognipunto. Dynamo 2 Capteur d’activité 24/7 Modèle: PE288 Guide de démarrage rapide FR VUE D’ENSEMBlE Unité principale Dynamo 2 1 23 54 Ref.Desciption 1Bouton d’opération • Appuyez pour…

Text truncated - open the document above for the full version.

Vicky Yuan

1 Photographs - EUT Constructional Details Test model No.: PE289

1 Photographs - EUT Constructional Details Test model No.: PE289

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140700368402 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1407003684RF Applicant: IDT Technology Limited Product Name: 2nd generation activity and sleep monitor wrist device Model No.(EUT): PE289 Add Model No.: PE280, PE281, PE288 FCC ID: NMTPE289 Standards: 47 CFR Part 1.1307(2013) 47 CFR Part 2.1093 (2013) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2014-07-16 Date of Test: 2014-07-21 to 2014-08-06 Date of Issue: 2014-08-14 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140700368402 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-08-14 Original Authorized for issue by: Tested By 2014-07-21 (Owen Zhou) /Project Engineer Date Prepared By 2014-08-06 (Molinda Li) /Clerk Date Checked By 2014-08-15 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140700368402 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140700368401 Page: 1 of 60 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No.: SZEM1407003684RF Applicant: IDT Technology Limited Product Name: 2nd generation activity and sleep monitor wrist device Model No.(EUT): PE289 Add Model No.: PE280, PE281, PE288 FCC ID: NMTPE289 Standards: 47 CFR Part 15, Subpart C (2013) Date of Receipt: 2014-07-16 Date of Test: 2014-07-21 to 2014-08-06 Date of Issue: 2014-08-14 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140700368401 Page: 2 of 60 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-08-14 Original Authorized for issue by: Tested By 2014-07-21 (Owen Zhou) /Project Engineer Date Prepared By 2014-08-06 (Molinda Li) /Clerk Date Checked By 2014-08-15 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140700368401 Page: 3 of 60 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart …

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: PE289 1.1 Conducted Emission 1.2 Radiated Emission 1.3 Radiated Spurious Emission