NMTPE932ACTIVITY TRACKER MOUDLE NAME

Trio™ Activity Tracker Device Information Display The Trio activity tracker displays the number of steps, distance in miles, calories burned, current time, and status of your FIT goals. These reset every day at midnight, but the data is stored on your Trio for up to a week. It might also display these other messages: • LOBAT—the battery is running low and needs to be recharged. • DATA—the Trio is syncing your data with the website or mobile app. • Trophy icon (flashing)—you’ve met 90% of your daily total-steps goal. • Trophy icon (steady)—you’ve met a FIT goal. • Bluetooth icon—the Trio is syncing with your mobile device via Bluetooth. Alert The Trio has a built-in alert to remind you to go for a walk throughout the day. An hour after your first five-minute walk (minimum 300 steps), the Trio will beep. If it doesn’t move within 10 minutes, it will beep again, and then a third time 10 minutes after that. The alerts will sound each hour until you meet your daily frequency goal (for example, four 5-minute walks). You can turn off the alert on your Settings page after you log in to the website. The change will take effect the next time your Trio syncs. Wearing The Trio is most accurate when you wear it close to your body—in a pocket, clipped to a bra strap, or on a belt or waistband. Battery The Trio has a rechargeable battery that should last up to two weeks. When you see the word “LOBAT” flash on the Trio’s screen, it’s time to charge the battery. To charge it, plug the clip of your Trio into the USB charging cable (with the white part and USB logo facing up, as shown). Then, plug the other end into your computer’s USB port. If the battery dies, the Trio will still save the existing data, but it won’t be able to record any new information until the battery is recharged. If you plug in the Trio to recharge the battery but the display doesn’t turn on, you might need to press the small reset button (under the charging clip). Before you do this, try re-inserting the charging cable the correct way into the Trio’s charging clip and your computer. If you press the Trio’s reset button, all your data will be erased and the settings will be restored to the factory defaults. Syncing To sync the Trio with your computer, you’ll need to plug in the small USB key and download and install the syncing software from our website. The Trio should sync automatically throughout the day if your computer is on, the USB key is plugged in, and the Trio is within 20 feet of it. To sync your Trio manually, press and hold the button while you’re within 20 feet of the USB key. The word “DATA” will appear on the display when it’s syncing. You can also sync with our mobile app using certain smartphones and tablets that have the Bluetooth 4.0 or Bluetooth Low Energy technology. Hardware Reset Resetting your Trio will erase all activity data that’s stored on the device and set the time to 12:00 midnight. If you need to reset the Trio, press the small button underneath the clip on the back side of the device. FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device meets the FCC and IC requirements for RF exposure in public or uncontrolled environments. Trio is a trademark of Fortify Technologies, LLC. Model #PE932.

1 Photographs - EUT Constructional Details Test model No.: PE932

PE932 MODEL: PART NO. / DOC. NO. : VERSION: PREPARED BY: APPROVED BY: REMARKS: PAGE: DATE: 270112593-11001-60 9.0 1 OF 1 Mark Yuan Terence Chen 2014-1-2 add”TRIO”LOGO -INJ. COLOR: -FINISHING:HIGH GLOSS FINISH REAR BUTTON :(under the clip) -PRINT COLOR: PMS427C(light grey) GREY VERSION -INJ. COLOR: -FINISHING:MATTE/SATIN FINISH CASING & CLIP: -COLOR: -FINISHING: FRONT BUTTON: HIGH GLOSSY PMS 425 (charcoal) PMS 425 (charcoal) PMS 425 (charcoal)

1 Photographs - EUT Constructional Details Test model No.: PE932

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM131200649402 Page: 1 of 5 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1312006494RF Applicant: IDT Technology Limited Manufacturer: IDT Technology Limited Factory: IDT Technology Limited Product Name: Activity Tracker Model No.(EUT): PE932 FCC ID: NMTPE932 Standards: 47 CFR Part 1.1307(2012) 47 CFR Part 2.1093 (2012) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2013-12-06 Date of Test: 2013-12-09 to 2013-12-27 Date of Issue: 2014-01-12 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM1131200649402 Page: 2 of 5 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE ........................................................................................................................................ 1 2 CONTENTS ............................................................................................................................................ 2 3 GENERAL INFORMATION ..................................................................................................................... 3 3.1 CLIENT INFORMATION ............................................................................................................................. 3 3.2 GENERAL DESCRIPTION OF EUT ............................................................................................................. 3 3.3 TEST LOCATION .................................................................................................................................... 3 3.4 TEST FACILITY....................................................................................................................................... 4 3.5 DEVIATION FROM STANDARDS ................................................................................................................. 4 3.6 ABNORMALITIES FROM STANDARD CONDITIONS......................................................................................... 4 3.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER .............................................................................. 4 4 SAR EVALUATION ................................................................................................................................. 5 4.1 RF EXPOSURE COMPLIANCE REQUIREMENT ...................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM131200649401 Page: 1 of 45 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1312006494RF Applicant: IDT Technology Limited Manufacturer: IDT Technology Limited Factory: IDT Technology Limited Product Name: Activity Tracker Model No.(EUT): PE932 FCC ID: NMTPE932 Standards: 47 CFR Part 15, Subpart C (2012) Date of Receipt: 2013-12-06 Date of Test: 2013-12-09 to 2013-12-27 Date of Issue: 2014-01-16 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM131200649401 Page: 2 of 45 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C Section 15.207 ANSI C63.10 2009 PASS Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(3) KDB558074 D01 PASS 6dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(2) KDB558074 D01 PASS Power Spectral Density 47 CFR Part 15, Subpart C Section 15.247 (e) KDB558074 D01 PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 PASS Radiated Spurious Emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 2009 PASS Band Edge (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 ANSI C63.10 2009 PASS SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM131200649401 Page: 3 of 45 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transactio…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: PE932 1.1 Conducted Emission 1.2 Radiated Emission 1.3 Radiated Spurious Emission