NMTSZ999Fabric Chest Belt with BLE

Bluetooth Fabric Chest belt SZ999 The SZ999 water resistant chest belt is equipped with the latest low energy Bluetooth 4.0 Sports System to achieve reliable transmission linkage with other devices that is with the logo . WEARING THE CHEST BELT Chest belt The chest belt counts your heartbeat and transmits this data to the watch. 1. Align the heart rate detector unit with the snap buttons on the belt strap. Secure by snapping into place. 2. Unfasten the belt strap. 3. Wet the conductive pads on the underside of the chest belt with a few drops of water or conductive gel to ensure solid contact. 4. Position the heart rate detector unit below your chest, while making sure logo is the right way up. Wrap the strap around your chest and fasten into place. To ensure an accurate heart rate signal, adjust the strap until the belt sits snugly below your pectoral muscles. TIPS • The position of the chest belt affects its performance. • Avoid areas with dense chest hair. • In dry, cold climates, it may take several minutes for the chest belt to function steadily. This is normal and should improve with several minutes of exercise. TRANSMISSION SIGNAL The SZ999 chest belt can be paired with your watch or sports accessory to provide heart rate readings. Locate your chest belt with the device as close as you can to help achieve pairing. The heart rate chest belt has a maximum transmission range of about 100 centimeters (40 inches). To search for heart rate signal, refer to watch instructions. NOTE While pairing, make sure to stay away from other devices and move the device to pair close to the watch. NOTE For SZ999 chest belt, pairing is only considered successful when the heart rate signal (such as an icon ) is found on the screen of your device. TROUBLESHOOTING In the event that you experience a weak signal or your signal is disrupted by interference in the environment, follow the instructions below to identify and resolve the situation. 1. The signal is weak - the device may only show “0”: • Shorten the distance between the heart rate chest belt and device. • Re-adjust the position of the heart rate chest belt. • Check the conductive pads are moist enough to ensure solid contact. • Check the batteries. If they are low or exhausted, the transmission range may be shortened. • Force a signal search on the device. 2. The gym equipment does not seem to work with your chest belt. • Most gym equipment is compatible with analog transmission. This chest belt does not transmit an analog signal, it only uses the low energy Bluetooth 4.0 technology. 3. Signal is jammed or there is interference from another person’s heart rate monitor: • There is too much interference in the environment for your heart rate monitor to function. Move to an area where the watch can register your heart rate reading and/or force another signal search. WARNING Signal interference in the environment can be caused by electromagnetic disturbances. These may occur near high voltage power lines, traffic lights, overhead lines of electric railways, electric bus lines or trams, televisions, car motors, bike computers, some motor driven exercise equipment, cellular phones or when you walk through electric security gates. Under interference, the heart rate reading may become unstable and inaccurate. REPLACE BATTERY Please replace battery promptly as it may affect the accuracy of the readings. To replace the chest belt battery: 1. Detach the heart rate detector unit from the belt strap. 2. Use a coin to open the battery compartment lid by turning it anticlockwise to open. 3. Remove the old battery and insert a new CR2032, 3V lithium battery. Make sure to place the battery in the compartment following the polarity +/-. 4. Secure the lid by turning the coin clockwise. IMPORTANT Remember to set the profiles after every battery replacement or reset. CARE INSTRUCTIONS The belt strap can be hand washed. Remember to detach the heart rate detector unit! • Do not wrap the detector unit in a wet towel nor with other wet materials. • Do not place or wash the heart rate detector unit under running water, instead clean it with a wet cloth. • Properly dry the detector unit immediately after use. • Do not store the chest belt in a hot (about 50°C) and humid (about 90%) environment. • Do not place the conductive rubber face down on a metal table or surface. • Do not bleach, dry clean, tumble dry or iron the belt strap. WATER RESISTANCE The SZ999 is water-resistant up to 10 meters (32.8 feet). Not recommended to use for swimming. RAIN SPLASHES ETC SHOWERING (WARM / COOL WATER ONLY) LIGHT SWIMMING / SHALLOW WATER SHALLOW DIVING / SURFING / WATER SPORTS SNORKELING / DEEP WATER DIVING 10M / 32.8 FT OK NO NO NO NO NOTE Ensure the battery compartment is secured and intact before exposing to excessive water. SPECIFICATIONS Heart rate detector dimension (L x W x H) 66.1 x 38 x12.5 mm (2.6 x 1.5 x 0.49 inches) Power 1 x CR2032 3V lithium battery Operating temperature 5 ̊C to 40 ̊C (41 ̊F to 104 ̊F) Storage temperature -20 ̊C to 60 ̊C (-4 ̊F to 140 ̊F) PRECAUTIONS To ensure you use your product correctly and safely, read these warnings and the entire user manual before using the product: • Use a soft, slightly moistened cloth. Do not use abrasive or corrosive cleaning agents, as these may cause damage. Use luke warm water and mild soap to clean the watch and chest belt thoroughly after each training session. Never use the products in hot water or store them when wet. • Do not bend or stretch the transmitter part of the chest belt. • Do not subject the product to excessive force, shock, dust, temperature changes, or humidity. Never expose the product to direct sunlight for extended periods. Such treatment may result in malfunction. Do not tamper with the internal components. Doing so will terminate the product warranty and may cause damage. The main unit contains no user-serviceable parts. • Take precautions when handling all battery types. • Remove the batteries whenever …

Text truncated - open the document above for the full version.

1 Photographs - EUT Constructional Details Test Model No.: SZ999

SZ999 (OS) scale:1:1 Label Location

1 Photographs - EUT Constructional Details Test Model No.: SZ999

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM120600361402 Page: 1 of 5 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page SAR Evaluation Report Application No: SZEM1206003614RF Applicant: iDT Technology Limited Manufacturer: iDT Technology Limited Factory: iDT Technology Limited Product Name: Fabric chest belt with BLE Model No.(EUT): SZ999 Standard: 47 CFR Part 1.1307(2011) 47 CFR Part 2.1093 (2011) KDB447498D01 FCC ID: NMTSZ999 Date of Receipt: 2012-08-01 Date of Test: 2012-08-15 to 2012-08-22 Date of Issue: 2012-08-27 Test Result: PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM120600361402 Page: 2 of 5 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents 1 COVER PAGE..............................................................................................................................................................1 2 CONTENTS..................................................................................................................................................................2 3 GENERAL INFORMATION........................................................................................................................................3 3.1 CLIENT INFORMATION...........................................................................................................................................3 3.2 GENERAL DESCRIPTION OF EUT.........................................................................................................................3 3.3 TEST LOCATION....................................................................................................................................................3 3.4 TEST FACILITY......................................................................................................................................................4 3.5 DEVIATION FROM STANDARDS.............................................................................................................................4 3.6 ABNORMALITIES FROM STANDARD CONDITIONS.................................................................................................4 3.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER......................................................................................4 4 SAR EVALUATION.........................................................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM120600361401 Page: 1 of 42 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1206003614RF Applicant: iDT Technology Limited Manufacturer: iDT Technology Limited Factory: iDT Technology Limited Product Name: Fabric chest belt with BLE Model No.(EUT): SZ999 FCC ID: NMTSZ999 Standards: 47 CFR Part 15, Subpart C (2011) Date of Receipt: 2012-08-01 Date of Test: 2012-08-15 to 2012-08-22 Date of Issue: 2012-08-27 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM120600361401 Page: 2 of 42 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) KDB558074 D01 ANSI C63.10 2009 PASS Conducted Peak Output Power 47 CFR Part 15, Subpart C Section 15.247 (b)(3) KDB558074 D01 ANSI C63.10 2009 PASS 6dB Occupied Bandwidth 47 CFR Part 15, Subpart C Section 15.247 (a)(2) KDB558074 D01 ANSI C63.10 2009 PASS Power Spectral Density 47 CFR Part 15, Subpart C Section 15.247 (e) KDB558074 D01 ANSI C63.10 2009 PASS Pseudorandom Frequency Hopping Sequence 47 CFR Part 15, Subpart C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2009) PASS Band-edge for RF Conducted Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 ANSI C63.10 2009 PASS RF Conducted Spurious Emissions 47 CFR Part 15, Subpart C Section 15.247(d) KDB558074 D01 ANSI C63.10 2009 PASS Radiated Spurious Emissions 47 CFR Part 15, Subpart C Section 15.205/15.209 KDB558074 D01 ANSI C63.10 2009 PASS Band Edge (Radiated Emission) 47 CFR Part 15, Subpart C Section 15.205/15.209 KDB558074 D01 ANSI C63.10 2009 PASS SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM120600361401 Page: 3 of 42 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if …

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup (Test Model No.: SZ999) 1.1 Radiated Emission 1.2 Radiated Spurious Emission