NS912XA58-26High Power MiniPCI 5.8GHz

Features • Compliant with IEEE 802.11a standard • Up to 26dBm output power with Built-in ESD Protection • RF ESD/EMP Immunity Threshold: 15KeV ① • Supports Atheros Proprietary "Super Mode" delivering up to 108 Mbps data link rate • High efficiency dual-PA design • High Performance combined with Low Power Consumption • Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard) • Single MMCX/U.FL Antenna Connector • Suitable for Embeded System or OEM Project • Affordable and Ideal for a Variety of Applications High Power MiniPCI 5.8GHz XA58-26 Technical Specifications Chipset Atheros AR54xx series（AR5414） Host Interface 32-bit mini-PCI Type IIIA+ (1.85mm longer than IIIA type) Operating Voltage 3.3 VDC 11a Cont. Tx @6M 3.5W 11a Cont. Rx 1.9W Power Consumption Standby 1.4W Antenna Connector 1 x MMCX IEEE 802.11a: 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 9Mbps 6Mbps Standards Conformance Super-A: 108Mbps 96Mbps 72Mbps 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 6Mbps Frequency Range IEEE 802.11a 5.725 ~ 5.850 GHz (US & Canada) Modulation Techniques OFMD: BPSK, QPSK, 16-QAM, 64-QAM Certification FCC, CE ROHS Compliance Yes Temperature Range Operating: -20ºC to 70ºC Storage: -40ºC to 90º Humidity Operating: 5% to 95% (non-condensing) Storage: Max.90% (non-condensing) Dimension 59.6 x52.8x 5.5 mm Weight 20 grams WLM54A-26-ESD MINIPCI CARD RADIO TX SPECIFICATIONS RX SPECIFICATIONS 5GHz 5600MHz 5700MHz 5785MHz 5825MHz Tolerance DataRate Sensitivity Tolerance 6Mbps 26dBm 26dBm 26dBm 26dBm +1.0/-1.5 dB 6Mbps -96dBm ±2dB 9Mbps 26dBm 26dBm 26dBm 26dBm +1.0/-1.5 dB 9Mbps -96dBm ±2dB 12Mbps 26dBm 26dBm 26dBm 26dBm +1.0/-1.5 dB 12Mbps -95dBm ±2dB 18Mbps 26dBm 26dBm 26dBm 26dBm +1.0/-1.5 dB 18Mbps -88dBm ±2dB 26dBm 26dBm 26dBm 26dBm +1.0/-1.5 dB 24Mbps 24Mbps -86dBm ±2dB 36Mbps 24dBm 24dBm 24dBm 24dBm +1.0/-1.5 dB 36Mbps -83dBm ±2dB 48Mbps 23dBm 23dBm 23dBm 23dBm +1.0/-1.5 dB 48Mbps -79dBm ±2dB 54Mbps 22dBm 22dBm 22dBm 22dBm +1.0/-1.5 dB 5GHz 54Mbps -76dBm ±2dB ADJUSTABLE CHANNEL SIZE SUPPORT 5MHz 10MHz 20MHz 40MHz ESD CABLE SPECIFICATIONS Cable Dimensions 26cm length Terminal Material Copper Attachment Procedure End of ESD Cable tied to Earth Ground ORDERING INFORMATION ② CODES Version CARTON DIMENSIONS WLM54A26ESD 8BS ESD For 50 pcs / carton, 0.45m*0.45m*0.24m/0.006=8.1KG • Module grounding cable included ② Configurations are subjected to change without notice Please contact Compex sales representatives for other available configurations Compliance Information FCC Compliance Statement: This device complies with Part 15 of the FCC Rules . Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device must accept any interference received, including interference that may cause undesired operation. Product that is a radio transmitter is labeled with FCC ID. FCC Caution: (1) Exposure to Radio Frequency Radiation. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. (2) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. (3) This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. (4) Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. ( 5) Outdoor Operations in the 5.15~5.25GHz band is prohibited. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. WARNING: This Wireless Mini PCI Adapter does not support ad-hoc mode Function The Host system using XA58-26, should have label indicated "Contains FCC ID: NS912XA58-26" IC warning -English: This device complies with Industry Canada licence-exemptRSS standard(s). Operation is subjectto the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operationof thedevice. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. -French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." Exposure to Radio Frequency Radiation: This equipment must beinstalled and operated in accordance with provided instructions and theantenna(s) used for this transmitter must be installed to provide aseparation distance of at least 20 cm from all persons and must not becollocated or operating in conjunction with any other antenna or transmitter.End-users and installers must be providedwith antenna installationinstructions and transmitter operating conditions for satisfying RF exposurecompliance. Transmitter Antenna Under Industry Canada regulations, this radio …

Text truncated - open the document above for the full version.

SCS-F26 Modular Approval Letter Page 1 of 4 Rev 7.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Modular Approval Declaration Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (Obsolete) 1.0 1.0 Dec-04-2006 Added IC Modular Letter (Obsolete) 1.0 2.0 Feb 16 2009 Add LMA and MA option (Obsolete) 2.0 3.0 April 14 2010 Revised per RSS Gen issue 3.0 (Obsolete) 3.0 4.0 Jan 12 2011 Removed Foot(2) (obsolete) 4.0 5.0 July 19 2011 Adding New note per KDB996369 D01 V01R03 (obsolete) 5.0 6.0 August 29 2011 Updated company template & Added editing restrictions (current) 6.0 7.0 Jan-31-2012 SCS-F26 Modular Approval Letter Page 2 of 4 Rev 7.0 Microhard Systems Inc. (Date) 04/28/2012 (Product name) FCC ID : NS912XA58-26 , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below : Questions are: * Please provide a detailed explanation if the answer is “No.” 1. “The modular transmitter must have its own RF shielding.” Yes / No 2. “The modular transmitter must have buffered modulation/data inputs.” Yes / No 3. “The modular transmitter must have its own power supply regulation.” Yes / No 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(c).” Yes / No 5. “The modular transmitter must be tested in a stand-alone configuration.” Yes / No 6. “The modular transmitter must be labeled with its own FCC ID number.” Yes / No 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate instruction along with the module to explain any such requirements.” Yes / No 8. “The modular transmitter must comply with any applicable RF exposure requirements.” Yes / No Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. (3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. Client’s signature Client’s name / title Hany Shenouda/Director Contact information / address Company Name: Microhard Systems Inc. Address: 150 Country Hills Landing NW Calgary Alberta Canada Tel. No: +403-248-0028 Fax No: +403-248-2762 SCS-F26 Modular Approval Letter Page 3 of 4 Rev 7.0 Microhard Systems Inc. (Date) 04/28/2012 (Product name) IC ID : 3143A-12XA5826 , is seeking IC Authorization as a modular transmitter / Limited Modular Transmitter (Please check one). The EUT meets the requirements for modular approval / Limited Modular Approval (Please check one) as detailed in RSS GEN. Compliance to each of the requirements is described below: * Please provide a detailed explanation if the answer is “No.” a. The radio elements must have the radio frequency circuitry must be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. Yes / No b. The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation. Yes / No c. The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module Yes / No d. The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. Yes / No e. The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing Yes / No f. The module shall comply with the Category I equipment labelling requirements. Yes / No g. The module shall comply with applicable RSS-102 exposure requirements, which are based on the intended…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 EXTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17

SYSTEMS INC. microhardmicrohard Model:XA58-26 High Power MiniPCI 5.8GHz FCC ID: NS912XA58-26 IC: 3143A-12XA5826 RoHS PN: MHS164600 This device complies with FCC Part 15 . Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation. MAC:

Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 EXTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17

Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA58-26 Date of Issue :2012-4-17 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. Rev.01 Page 1 of 2 APPENDIX I RADIO FREQUENCY EXPOSURE LIMIT According to RSS-Gen §5.5, before equipment certification is granted, the applicable requirements of RSS-102 shall be met. EUT Specification EUT High Power MiniPCI 5.8GHz Frequency band (Operating) Bluetooth: 2.402GHz ~ 2.480GHz WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.745GHz ~ 5.825GHz Device category Portable (<20cm separation) Mobile (>20cm separation) Exposure classification Occupational/Controlled exposure (S=5mW/cm 2 ) General Population/Uncontrolled exposure (S=1mW/cm 2 ) Antenna diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Max. output power IEEE 802.11a: 26.19 dBm (415.91mW) Antenna gain (Max) 2 dBi (Numeric gain: 1.58) Evaluation applied MPE Evaluation* SAR Evaluation N/A Remark: 1.The maximum output power is 26.19dBm (415.91mW) at 5745MHz (with 1.58 numeric antenna gain.) 2.DTS device is not subject to routine RF evaluation; MPE estimate is used to justify the compliance. 3.For mobile or fixed location transmitters, no SAR consideration applied. The maximum power density is 1.0 mW/cm 2 even if the calculation indicates that the power density would be larger. TEST RESULTS No non-compliance noted. Calculation Given d GP E ×× = 30 & 3770 2 E S= Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields: 2 3770 30 d GP S ×× = Changing to units of mW and cm, using: Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA58-26 Date of Issue :2012-4-17 Page 2 of 2 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Yields () () 2 2 0796.0 100/3770 1000/30 d GP d GP S × ×= × ×× = Equation 1 Where d = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 Maximum Permissible Exposure EUT output power = 415.91mW Numeric Antenna gain =1.58 Substituting the MPE safe distance using d = 20 cm into Equation 1: Yields GPS××=000199.0 Where P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 Æ Power density =0.13077mW / cm 2 (For mobile or fixed location transmitters, the maximum power density is 1.0 mW/cm2 even if the calculation indicates that the power density would be larger.) END OF REPORT

Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA58-26 Date of Issue :2012-4-17 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by A2LA or any government agencies. The test results in the report only apply to the tested sample. Rev.01 Page 1 of 41 FCC 47 CFR PART 15 SUBPART C Industry Canada RSS-210 Test Report For Product Name: High Power MiniPCI 5.8GHz Brand Name: Microhard Model No.: XA58-26 Series Model: N/A Test Report Number: KS120327A03-RPB Issued for Microhard Systems Inc. 150 Country Hills Landing NW Calgary Alberta Canada T3K 5P3 Issued by Compliance Certification Services Inc. Kun shan Laboratory No.10 Weiye Rd., Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China TEL: 86-512-57355888 FAX: 86-512-57370818 Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA58-26 Date of Issue :2012-4-17 Page 2 of 41 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION ...................................................................................................3 2 EUT DESCRIPTION........................................................................................................................4 3 TEST METHODOLOGY..................................................................................................................5 3.1. DESCRIPTION OF TEST MODES .........................................................................................5 3.2. EUT EXERCISE .....................................................................................................................5 3.3. GENERAL TEST PROCEDURES ..........................................................................................5 3.4. RESTRICTED BANDS OF OPERATIONS .............................................................................6 3.5. SETUP CONFIGURATION OF EUT ......................................................................................6 3.6. SUPPORT EQUIPMENT........................................................................................................6 4 INSTRUMENT CALIBRATION .......................................................................................................7 4.1. MEASUREMENT EQUIPMENT USED ..................................................................................7 4.2. MEASUREMENT UNCERTAINTY .........................................................................................8 5 FACILITIES AND ACCREDITATIONS ...........................................................................................9 5.1. FACILITIES............................................................................................................................9 5.2. EQUIPMENT..........................................................................................................................9 5.3. TABLE OF ACCREDITATIONS AND LISTINGS ....................................................................9 6 REQUIREMENTS .........................................................................................................................10 6.1. 6 DB BANDWIDTH MEASUREMENT ...................................................................................10 6.2. 99% BANDWIDTH MEASUREMENT...................................................................................14 6.3. PEAK OUTPUT POWER......................................................................................................18 6.4. AVERAGE POWER .............................................................................................................19 6.5. PEAK POWER SPECTRAL DENSITY MEASUREMENT.....................................................20 6.6. CONDUCTED SPURIOUS MEASUREMENT ......................................................................24 6.7. RADIATED EMISSIONS ......................................................................................................28 6.8. POWER LINE CONDUCTED MEASUREMENT ..................................................................40 Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA58-26 Date of Issue :2012-4-17 Page 3 of 41 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. 1 TEST RESULT CERTIFICATION Product Name: High Power MiniPCI 5.8GHz Trade Name: Microhard Model Name.: XA58-26 Series Model: N/A Applicant Discrepancy: Initial Device Category: MOBILE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Date of Test: 2012-4-2~2012-4-14 Applicant: Microhard Systems Inc. 150 Country Hills Landing NW Calgary Alberta Canada T3K 5P3 Manufacturer: Microhard Systems Inc. 150 Country Hills Landing NW Calgary Alberta Canada T3K 5P3 Application Type: Certification APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C IC RSS-210 Issue 8 with December 2010 C63.4: 2009 No non-compliance noted The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4：2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247 and RSSS-210,RSSS-Gen. We hereby certify that: Compliance Certification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test resul…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 Page 1 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. AC POWER LINE CONDUCTED EMISSION TEST Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 Page 2 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. RADEATED EMISSION TEST Compliance Certification Services Inc. Report No: KS120327A03-RPB FCC ID: NS912XA58-26 IC: 3143A-12XA5826 Date of Issue :2012-4-17 Page 3 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. CONDUCTED TEST