NUL-924Router Plugin Unit

Bluetooth Enabled Gateway Setup Bluetooth Enabled Gateway Setup 61844 / 01 Requirements: • Internet service • Internet router with available Ethernet port • Active Kevo Plus membership Requirements: • Internet service • Internet router with available Ethernet port • Active Kevo Plus membership Connect and fully tighten the antenna to the back of the gateway. Bend the antenna so that it points straight up. Connect and fully tighten the antenna to the back of the gateway. Bend the antenna so that it points straight up. Plug the USB cable’s power jack end into the gateway. Plug the USB connector into the power adapter. Plug the power adapter into a power outlet. Plug the USB cable’s power jack end into the gateway. Plug the USB connector into the power adapter. Plug the power adapter into a power outlet. Make sure the lights on the gateway are functioning. See the Light Ring Colors on page 2. Follow the instructions inside the Kevo app to configure your gateway. Make sure the lights on the gateway are functioning. See the Light Ring Colors chart on page 2. Follow the instructions inside the Kevo app to configure your gateway. Once configured, you may control the gateway with the Kevo app or mykevo.com Once configured, you may control the gateway with the Kevo app or mykevo.com. Plug one end of the Ethernet cable into the gateway. Plug the other end into your internet router. Plug one end of the Ethernet cable into the gateway. Plug the other end into your internet router. 1 3 2 4 ©2014 Kwikset Corporation Color Color Reason Reason White White Booting up Booting up Blue Blue Normal operation Normal operation Red Red Not connected to Kevo Plus Not connected to Kevo Plus Magenta Magenta Not connected to Kevo deadbolt Not connected to Kevo deadbolt Australia Toll Free: 1800 623 118 Email: [email protected] Website: www.spectrumbrands.com.au Spectrum Brands Australia Pty Ltd Locked Bag 3004 Braeside, Victoria 3195 Australia New Zealand Toll Free: 0800 736 776 Email: [email protected] Website: www.spectrumbrands.co.nz Spectrum Brands New Zealand Ltd PO Box 9817 Newmarket, Auckland 1149 New Zealand USA & Canada 1-800-327-5625 Chile 56-229382400 Colombia 57-13441460 México 52-8141709475 Australia Warranty Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits provided by this warranty are in addition to all other rights and remedies in respect of this product which you may have under Australian Consumer Law or otherwise. If your product is defective, you can have it repaired or replaced under our Lifetime warranty. To claim under our warranty, please return the defective item along with the packaging, the original receipt, your address and your signature by pre paid postage to Spectrum Brands Australia Pty Ltd at the address on pack at any time following purchase. Spectrum Brands Australia Pty Ltd will then replace or repair the item and return it to you at our cost. Light Ring Colors Light Ring Colors Kevo Support Kevo Support Regulatory Compliance Regulatory Compliance This product complies with standards established by the following regulatory bodies: • Federal Communications Commission (FCC) • Industry Canada FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Industry Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: ( 1 ) this device may not cause interference, and ( 2 ) this device must accept any interference, including interference that may cause undesired operation of the device. Este producto cumple con las normas establecidas por los siguientes organismos reguladores: • Comisión Federal de Comunicaciones (FCC) • Industry Canada FCC Este dispositivo cumple con la 15ª parte del reglamento de la FCC. Su funcionamiento está sujeto a las siguientes dos condiciones: ( 1 ) este dispositivo no deberá causar ninguna interferencia dañina, y ( 2 ) este dispositivo deberá aceptar cualquier interferencia recibida, incluyendo aquélla que podría causar un funcionamiento no deseado. Se realizaron pruebas a este equipo cuyos resultados revelaron que cumple con los límites establecidos para un dispositivo digital de la Clase B, conforme a la 15ª parte del r…

Text truncated - open the document above for the full version.

4/2/2015 Compatible Electronics TCB 114 Olinda Drive Brea, California 92823 Subject: Modifications to the device CETCB 114 Olinda Drive Brea, CA 92823 Gentlemen: This letter is to formally notify you that the following modification(s) had been completed by Compatible Electronics, Inc. to our NUL-924 - Kevo RPU - BLE Gateway during FCC certification, and will be implemented in production. Modification(s): The power of BLE channel 37 at 2402MHz is reduced to -8dBm.

Designed in Lake Forest, California. Made in Mexico. Model: 924-GED1900-RPU FCC ID: NUL-924 IC: 3022A-GED1900 Input: 5VDC/0.5A

Report Number: D40707R1 FCC ID: NUL-924 FCC Part 15 Subpart B & C Section 15.249 Test Report 20621 PASCAL WAY, LAKE FOREST, CALIFORNIA, 92630 • PH: (949) 587-0400 FX: (949) 587-0476 Page 1 of 17 FCC PART 15, SUBPART B & C CLASS B TEST REPORT TEST METHOD: ANSI C63.4 & ANSI C63.10 For RPU Model: 924-GED1900-RPU Prepared for KWIKSET CORP. 19701 DAVINCI LAKE FOREST, CA 92630 Prepared by:_____________________ TOREY OLIVER Approved by:____________________ MATT HARRISON COMPATIBLE ELECTRONICS INC. 20621 PASCAL WAY LAKE FOREST, CALIFORNIA 92630 (949) 587-0400 DATE: JULY 7, 2014 REPORT APPENDICES TOTAL BODY A B C D E PAGES 17 2 2 2 16 23 62 This report shall not be reproduced, except in full, without the written approval of Compatible Electronics. Report Number: D40707R1 FCC ID: NUL-924 FCC Part 15 Subpart B & C Section 15.249 Test Report 20621 PASCAL WAY, LAKE FOREST, CALIFORNIA, 92630 • PH: (949) 587-0400 FX: (949) 587-0476 Page 2 of 17 TABLE OF CONTENTS Section / Title PAGE GENERAL REPORT SUMMARY 4 SUMMARY OF TEST RESULTS 4 1. PURPOSE 5 2. ADMINISTRATIVE DATA 6 2.1 Location of Testing 6 2.2 Traceability Statement 6 2.3 Cognizant Personnel 6 2.4 Date Test Sample was Received 6 2.5 Disposition of the Test Sample 6 2.6 Abbreviations and Acronyms 6 3. APPLICABLE DOCUMENTS 7 4. DESCRIPTION OF TEST CONFIGURATION 8 4.1 Description of Test Configuration - EMI 8 4.1.1 Photograph of Test Configuration - EMI 8 4.1.2 Cable Construction and Termination 9 5. LISTS OF EUT, ACCESSORIES AND TEST EQUIPMENT 10 5.1 EUT and Accessory List 10 5.2 EMI Test Equipment 11 6. TEST SITE DESCRIPTION 12 6.1 Test Facility Description 12 6.2 EUT Mounting, Bonding and Grounding 12 7. CHARACTERISTICS OF THE TRANSMITTER 13 7.1 Channel Number and Frequencies 13 7.2 Antenna 13 8. TEST PROCEDURES 14 8.1 RF Emissions 14 8.1.1 Conducted Emissions Test 14 8.1.2 Radiated Emissions (Spurious and Harmonics) Test 15 8.1.3 Fundamental Field Strength 16 8.1.4 Emissions Radiated Outside of the Fundamental Frequency Band 16 8.1.5 Duty Cycle 16 9. TEST PROCEDURE DEVIATIONS 17 10. CONCLUSIONS 17 Report Number: D40707R1 FCC ID: NUL-924 FCC Part 15 Subpart B & C Section 15.249 Test Report 20621 PASCAL WAY, LAKE FOREST, CALIFORNIA, 92630 • PH: (949) 587-0400 FX: (949) 587-0476 Page 3 of 17 LIST OF APPENDICES APPENDIX TITLE A Laboratory Accreditations B Modifications to the EUT C Additional Models Covered Under This Report D Diagrams, Charts and Photos  Test Setup Diagrams  Antenna and Amplifier Gain Factors  Radiated and Conducted Emissions Photos E Data Sheets LIST OF FIGURES FIGURE TITLE 1 Plot Map And Layout of Test Site 2 Conducted Emissions Setup Report Number: D40707R1 FCC ID: NUL-924 FCC Part 15 Subpart B & C Section 15.249 Test Report 20621 PASCAL WAY, LAKE FOREST, CALIFORNIA, 92630 • PH: (949) 587-0400 FX: (949) 587-0476 Page 4 of 17 GENERAL REPORT SUMMARY This electromagnetic emission report is generated by Compatible Electronics Inc., which is an independent testing and consulting firm. The test report is based on testing performed by Compatible Electronics personnel according to the measurement procedures described in the test specifications given below and in the "Test Procedures" section of this report. The measurement data and conclusions appearing herein relate only to the sample tested and this report may not be reproduced in any form except in full, without the written permission of Compatible Electronics. This report must not be used to claim product endorsement by NVLAP, NIST or any other agency of the U.S. Government. Device Tested: RPU Model: 924-GED1900-RPU S/N: None Product Description: The EUT is a RPU for operating a wireless door lock via Bluetooth 4.0 Low Energy technology. Modifications: The EUT was modified in order to comply with specifications. Please see the list of modifications in Appendix B. Manufacturer: Kwikset Corp. 19701 DaVinci Lake Forest, Ca 92630 Test Date: July 3 & 7, 2014 and April 2, August 24, 2015 Test Specifications: EMI requirements CFR Title 47, Part 15 Subpart C Sections 15.205, 15.207, 15.209 and 15.249 FCC Part 15 Subpart B sections 15.107 and 15.109 Test Procedure: ANSI C63.10 and ANSI C63.4 SUMMARY OF TEST RESULTS TEST DESCRIPTION RESULTS 1 Conducted RF Emissions, 150 kHz - 30 MHz. Complies with the limits of CFR Title 47 Part 15 Subpart B section 15.107 and Subpart C Section 15.207. 2 Radiated RF Emissions & Harmonics, 9 kHz – 24,800 MHz Complies with the limits of CFR Title 47 Part 15 Subpart B section 15.109 and Subpart C Sections 15.205 and 15.209. 3 Fundamental Field Strength Complies with CFR Title 47 Part 15 Subpart C Section 15.249(a) 4 Emissions Radiated Outside of the Fundamental Frequency Band Complies with CFR Title 47 Part 15 Subpart C Section 15.249(d) and 15.205 Report Number: D40707R1 FCC ID: NUL-924 FCC Part 15 Subpart B & C Section 15.249 Test Report 20621 PASCAL WAY, LAKE FOREST, CALIFORNIA, 92630 • PH: (949) 587-0400 FX: (949) 587-0476 Page 5 of 17 1. PURPOSE This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the RPU Model: 924-GED1900-RPU. The EMI measurements were performed according to the measurement procedure described in ANSI C63.10 and ANSI C63.4. The tests were performed in order to determine whether the electromagnetic emissions from the equipment under test, referred to as EUT (equipment under test) hereafter, are within the specification limits defined by the Code of Federal Regulations Title 47, Part 15 subpart B sections 15.107 and 15.109, Part 15 Subpart C sections 15.205, 15.207, 15.209 and 15.249. Report Number: D40707R1 FCC ID: NUL-924 FCC Part 15 Subpart B & C Section 15.249 Test Report 20621 PASCAL WAY, LAKE FOREST, CALIFORNIA, 92630 • PH: (949) 587-0400 FX: (949) 587-0476 Page 6 of 17 2. ADMINISTRATIVE DATA 2.1 Location of Testing The EMI tests described herein were performed at the test facility of Compatible Electronics, 20621 Pascal Way Lake Forest, California 92630. 2.2 Traceability S…

Text truncated - open the document above for the full version.