NUL5024095ZWVWireless Entry Lock for Home Automation

FOR PRODUCT WITH A HOME AREA NETWORK (HAN) GATEWAY SYSTEM CONNECTION. 1. Please make sure you have followed all the steps in the lock Installation and Programming Manual. 4. User Code Information: ● Code or codes that are programmed before the installation of the daughter card will be disabled. ● Code or codes that are programmed after the installation of the daughter card will remain valid. ● Once the lock has been included into the (HAN) system, you can program up to 30 codes. ● We suggest you add and change codes from the system controller. ● Deleting a code can only be done from the system controller. 3. For inclusion or exclusion of the lock, refer to the Home Area Network (HAN) system instructions and note functions referred to in Figure 2 and the chart below. 2. Make sure the RF daughter card is properly installed, seated and connected, see Figure 1, callout . Light (under the reference card) will illuminate Yellow for 5 seconds during the Inclusion process and will illuminate Red for 5 seconds during the Exclusion process. POUR UN PRODUIT COMPRENANT UNE CONNEXION À UN SYSTÈME DE COMMUNICATION INTER-RÉSEAU DOMESTIQUE. 1. Veuillez vous assurer de suivre toutes les étapes dans le Guide de programmation et d'installation du serrure. 3. Pour inclure ou exclure le serrure, veuillez consulter les instructions du système de réseau domestique et prenez note des fonctions dont on fait référence à la Figure 2 et le tableau dessous. 2. Veuillez vous assurer que la carte fille RF est correctement installée, bien fixée et connectée, consultez la Figure 1, point . La lumière (sous la carte de référence) s'allumera en Jaune pendant 5 secondes au cours du processus d'inclusion et elle s'allumera en Rouge pendant 5 secondes au cours du processus d'exclusion. 4. Information sur le code d'utilisateur: ● Le code ou les codes qui sont programmés avant l'installation de la carte fille seront désactivés. ● Le code ou les codes qui sont programmés après l'installation de la carte fille resteront activés. ● Une fois le serrure inclus dans le système inter-réseau domestique, vous pouvez programmer jusqu'à 30 codes. ● Nous vous suggérons d'ajouter et de changer les codes du contrôleur de système. ● La suppression d'un code ne peut être effectuée qu'à partir du contrôleur de système. CONFORMITÉ RÈGLEMENTAIRE Ce produit est conforme aux normes établies par les organismes de règlementation suivants : • Federal Communications Commission (FCC, États-Unis) • Industrie Canada Copyright © 2009 Black & Decker Corporation Fig. 2 C C A A A Fig. 1 RF Protocol Zigbee Z-Wave Inclusion Process D B BB Button used in Exclusion Process Button used in Protocole RF Zigbee Z-Wave Processus De Inclusion D B BB Bouton utilisé pour le Bouton utilisé pour le Processus De Exclusion REGULATORY COMPLIANCE This product complies with standards established by the following regulatory bodies: • Federal Communications Commission (FCC) • Industry Canada FCC FCC ID: NUL5024093ZGB (Wireless Lock Module 5024093) FCC ID: NUL5024095ZWV (Wireless Lock Module 5024095) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi-cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. INDUSTRY CANADA This Class B digital apparatus complies with Canada ICES-003. CAN/CSA-C22.2 NO. 14-05 (Industrial Control Equipment) Operation is subject to the following two conditions: ( 1 ) this device may not cause interference, and ( 2 ) this device must accept any interfer- ence, including interference that may cause undesired operation of the device. Canadian ID IC: 3022A-5024093ZGB Canadian ID IC: 3022A-5024095ZWV Z-WAVE • Security enabled Z-Wave product • Security enabled Z-Wave controller must be used in order to fully utilize product. This Z-Wave-enabled door lock can be included, operated, and is fully interoperable with any Z-Wave secure controller. For more information, visit: http://www.Kwikset.com/wirelesslocks/products.aspx ENGLISH INSTRUCTIONS D'INSTALLATION FRANÇAIS INSTALLATION INSTRUCTIONS 44571-02 1 / 2 Press program button below once to enter the 1st code & twice for the 2nd code Enter code on exterior keypad Press on exterior keypad to set code READY PROGRAM BUTTON B D C La luz (debajo de la tarjeta de referencia) se iluminará de color Amarillo por 5 segundos durante el proceso de inclusión y de color Rojo por 5 segundos durante el proceso de exclusión. PARA PRODUCTOS CON CONEXIÓN A SISTEMA DE PASARELA DE RED DE ÁREA DOMÉSTICA. 1. Asegúrese de seguir todos los pasos indicados en el Manual de Programación e Instalación de la cerradura. 4. Información acerca del código del usuario: ● Los códigos prog…

Text truncated - open the document above for the full version.

SHEET SCALE REV DWG NO SIZE TITLE DRAFTER CHECKED ENGINEER APPROVED DATE DATE DATE DATE A B C D A B C D 4 3 2 1 ZENIA LISETTE ISABEL DELGADO 4 3 1 RELEASE STATE ITER NOTES: UNLESS OTHERWISE SPECIFIED THIS DOCUMENT IS THE PROPERTY OF BLACK & DECKER AND/OR ITS AFFILIATES. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO BLACK & DECKER. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED, OR PUBLISHED WITHOUT BLACK & DECKER'S PRIOR WRITTEN CONSENT. 1.00 .50 REVDESCRIPTIONDATEDRAFTERENGINEERAPPROVED BY 1PRODUTION RELEASE PER EO104365-1112/22/09M.EMORYM.EMORYM.MARIDAKIS PDM REFD: 1.0M: 1.0 5/1 1 OF 1 BLACK & DECKER HARDWARE AND HOME IMPROVEMENT 19701 DA VINCI, LAKE FOREST, CA 92610 LABEL, FCC ID, Z-WAVE B DO NOT SCALE DRAWING 5042462 Production1 0 M.EMORY12/22/09 M.EMORY12/22/09 M.MARIDAKIS12/22/09 THIRD ANGLE PROJECTION KWIKSET SHEET SCALE REV DWG NO SIZE TITLE DRAFTER CHECKED ENGINEER APPROVED DATE DATE DATE DATE A B C D A B C D 4 3 2 1 ZENIA LISETTE ISABEL DELGADO 4 3 1 RELEASE STATE ITER NOTES: UNLESS OTHERWISE SPECIFIED THIS DOCUMENT IS THE PROPERTY OF BLACK & DECKER AND/OR ITS AFFILIATES. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO BLACK & DECKER. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED, OR PUBLISHED WITHOUT BLACK & DECKER'S PRIOR WRITTEN CONSENT. .13 .27 QTYDESCRIPTIONPRT NO. ITEM NO. 1PWA, Z-WAVE50240841 1HANDLE, WIRELESS BOARD50240852 1LABEL, FCC ID, Z-WAVE50424623 REVDESCRIPTIONDATEDRAFTERENGINEERAPPROVED BY 1PRODUCTION RELEASE PER EO104365-1212/29/09M.EMORYM.EMORYM.MARIDAKIS PDM REFD: 1.0M: 1.0 2/11 OF 1 BLACK & DECKER HARDWARE AND HOME IMPROVEMENT 19701 DA VINCI, LAKE FOREST, CA 92610 ASM, Z-WAVE B DO NOT SCALE DRAWING 5024095 Production1 0 M.EMORY12/29/09 M.EMORY12/29/09 M.MARIDAKIS12/29/09 THIRD ANGLE PROJECTION KWIKSET rev 3 BDHHI_WC_TEMPLATE_ASSM_B 1 2 3

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 The Nation’s First Licensed Nationally Recognized Testing Laboratory April 2, 2010 Black & Decker 3218 Main St Suite A202 Philadelphia, PA 19128 Dear Mike Balog, Enclosed is the EMC Wireless test report for compliance testing of the Black & Decker, RF 5024095 Lock as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-06 ed.), Part 15, Subpart B, ICES-003, Issue 4 February 2004 for a Class B Digital Device and FCC Part 15 Subpart C, RSS-210, Issue 7, June 2007 for Intentional Radiators. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please feel free to contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Warnell Documentation Department Reference: (\Black & Decker\EMC28462-FCC249) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. Electromagnetic Compatibility Black & Decker Cover Page RF 5024095 Lock CFR Title 47, Part 15B, 15.249; RSS-210, Issue 7, June 2007 & ICES-003 MET Report: EMC28462-FCC249 © 2010, MET Laboratories, Inc. Page ii of vii Electromagnetic Compatibility Criteria Test Report for the Black & Decker Model RF 5024095 Lock Verified under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class B Digital Devices & 15.249 Subpart C & RSS-210, Issue 7, June 2007 for Intentional Radiators MET Report: EMC28462-FCC249 April 2, 2010 Prepared For: Black & Decker 3218 Main St Suite A202 Philadelphia, PA 19128 Prepared By: MET Laboratories, Inc. 914 W. Patapsco Ave. Baltimore, MD 21230 Electromagnetic Compatibility Black & Decker Cover Page RF 5024095 Lock CFR Title 47, Part 15B, 15.249; RSS-210, Issue 7, June 2007 & ICES-003 Electromagnetic Compatibility Criteria Test Report for the Black & Decker Model RF 5024095 Lock Tested Under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class B Digital Devices & 15.249 Subpart C & RSS-210, Issue 7, June 2007 for Intentional Radiators Dusmantha Tennakoon, Project Engineer Jennifer Warnell Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of the FCC Rules Parts 15B, 15.249 and Industry Canada standards ICES-003, Issue 4 February 2004, RSS-210, Issue 7, June 2007 under normal use and maintenance. Shawn McMillen, Wireless Manager Electromagnetic Compatibility Lab MET Report: EMC28462-FCC249 © 2010, MET Laboratories, Inc. Page iii of vii Electromagnetic Compatibility Black & Decker Report Status RF 5024095 Lock CFR Title 47, Part 15B, 15.249; RSS-210, Issue 7, June 2007 & ICES-003 MET Report: EMC28462-FCC249 © 2010, MET Laboratories, Inc. Page iv of vii Report Status Sheet Revision Report Date Reason for Revision  April 2, 2010 Initial Issue. Electromagnetic Compatibility Black & Decker Table of Contents RF 5024095 Lock CFR Title 47, Part 15B, 15.249; RSS-210, Issue 7, June 2007 & ICES-003 MET Report: EMC28462-FCC249 © 2010, MET Laboratories, Inc. Page v of vii Table of Contents I. Executive Summary .................................................................................................................................................1 A. Purpose of Test ........................................................................................................................................... 2 B. Executive Summary.................................................................................................................................... 2 II. Equipment Configuration .......................................................................................................................................3 A. Overview .................................................................................................................................................... 4 B. References .................................................................................................................................................. 5 C. Test Site ...................................................................................................................................................... 5 D. Description of Test Sample......................................................................................................................... 5 E. Equipment Configuration ........................................................................................................................... 6 F. Support Equipment ..................................................................................................................................... 6 G. Ports and Cabling Information.................................................................................................................... 6 H. Mode of Operation...................................................................................................................................... 7 I. Method of Monitoring EUT Operation....................................................................................................... 7 J. Modifications.............................................................................................................................................. 7 a) Modifications to EUT..................…

Text truncated - open the document above for the full version.