O2J-AS4000CT-PCSCentral Terminal PCS Base Station

605-0000-426 © 2000 Airspan Communications Ltd Draft Issue 6.0 Date 4/4/00 AS8100 Sitespan User Guide Version 3.7 Sitespan User Guide Version 3.7 605-0000-426 Preface Draft Issue 6.0. Date 4/4/00 Page 2 of 305 This Page Intentionally Blank Sitespan User Guide Version 3.7 605-0000-426 Preface Draft Issue 6.0. Date 4/4/00 Page 3 of 305 Notice 1. This manual is subject to revision. 2. All rights reserved. 3. Right of modification reserved. 4. This manual is supplied without liability for errors or omissions. 5. No part of this manual may be reproduced or used except as authorised by contract or other written permission. 6. This equipment is conditioned by the requirement that no modifications are made to the equipment unless the changes or modifications are expressly approved by the Airspan Networks Inc 7. Prerequisite skills: Personnel installing, commissioning, and maintaining the Airspan products must have a basic knowledge of telephony and radio communications, and have experience in installing, commissioning and maintaining telecommunications products. Airspan provides a range of comprehensive training courses specifically aimed at providing operators/users of Airspan products with the prerequisite skills to install, commission and or maintain the product. The courses are tailored to provide the level of training required by the operator/user. 8. AS4000 and AS8100 are brands of Airspan Networks Inc For additional information on Airspan Systems, please call your Airspan Representative, or contact Airspan at: Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Call (44) 895 4677100 Fax (44) 895 4677101 email sales@ airspan.com Sitespan User Guide Version 3.7 605-0000-426 Preface Draft Issue 6.0. Date 4/4/00 Page 4 of 305 This Page Intentionally Blank Sitespan User Guide Version 3.7 605-0000-426 Preface Draft Issue 6.0. Date 4/4/00 Page 5 of 305 Safety Instructions - Warnings and Cautions SAFETY 1. Read and follow all warning notices and instructions marked on the product or included in this manual 2. Do not allow anything to rest on the power cord and do not locate the product where persons could step or walk on the power cord. 3. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. 4. No hazardous RF radiation is emitted from the equipment. Measured at the surface of the CRU radome, when transmitting, the maximum total power radiated from the CRU is 0.01% of the UK National Radiological Protection Board basic restriction per kg. of body part. WARNING - HAZARDOUS VOLTAGES On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power. Remove metal jewellery that could come into contact with AC power. On DC sections, short circuiting the low voltage, low impedance circuits can cause severe arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits. Electro-Static Discharge ESD Electro-Static Discharge. Many circuits contain devices that are susceptible to damage from high impedance voltage sources. To avoid such risks always follow anti-static procedures where marked. Sitespan User Guide Version 3.7 605-0000-426 Preface Draft Issue 6.0. Date 4/4/00 Page 6 of 305 NOTE To the best of ACL’s knowledge, Airspan products do not contain hazardous substances (as defined in UK ‘Control of Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances Regulations 1990’). At the end of any Airspan product’s life cycle, the customer should consult with ACL to ensure that the product is disposed of in conformance with the relevant regulatory requirements The Symbol on the Airspan Products signifies that they have been certified according to the EMC directive 89/336/EEC. The products fulfil the requirements according to the following standards: EN50082-1Immunity. EN55022 Group 1 Class A for the Central Terminal Emissions. EN55022 Group 1 Class B for the Subscriber Terminal Emissions. WARNING The Subscriber Terminal equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. AS8100 Sitespan User Guide Version 3.7 605-0000-426 IXL 001 Draft Issue 6.0. Date 4/4/00 Page 7 of 305© 2000 Airspan Communications Ltd INDEX TASK LIST Preface: Safety Instructions Warnings and Cautions Index Task ListIXL-001 GENERAL SYSTEM INFORMATION: GSI Introduction.GSI-001 Sitespan System Overview GSI-002 OverviewGSI-003 Service States and StatusGSI-004 Getting Started. GSI-005 Hardware InstallationGSI-006 Installing the Sitespan Server PCGSI-007 Physical Connection to Release 2 Airspan GSI-008 Physical Connection to FA Airspan GSI-009 Physical Connection to DA Airspan GSI-010 Operating Sitespan for Fixed Assignment over Demand Assignment Backhaul GSI-011 Installing the Sitespan Equipment View PCGSI-012 AS8100 Sitespan Software InstallationGSI-013 Basic OperationsGSI-014 SiteSpan Equipment View Menu System GSI-015 Server Menu System GSI-016 Selecting Views GSI-017 Managing a Network of Server SitesGSI-018 Using Windows NT RAS to connect Sitespan Client and ServerGSI-019 DETAIL LEVEL PROCEDURES: DLP 1. General procedures Notes on using Detail Level ProceduresDLP-001 Set-up User Accounts and Dial-in Access Rights DLP-002 Creating a Phone Book for the Equipment View PC DLP-003 Monitoring A Modem Connection To A ServerDLP-004 Starting SitespanDLP-005 Sitespan Version DLP-006 Setting up the Sitespan Display Options DLP-007 File Open -DLP-008 Create a Server Connection Record -DLP-009 Create Site DLP-010 Deleting SitesDLP-011 Connect to a Server DLP-012 Disconnect from a ServerDLP-013 Create Airspan RackDLP-014 Deleting Airspan RacksDLP-015 AS8100 Sitespan User Guide Version 3.7 605-0000-426 IXL 001 Draft Issue 6.0. Date 4/4/00 Page 8 of …

Text truncated - open the document above for the full version.

605-0000-453Issue 1.2dr Date 7/02/00 AS4000 Wireless Local Loop System Demand Assignment Access Concentrator Installation and Commissioning AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 2 of 8 This Page Intentionally Blank AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 3 of 8 Notice 1. This manual is subject to revision. 2. All rights reserved. 3. Right of modification reserved. 4. This manual is supplied without liability for errors or omissions. 5. No part of this manual may be reproduced or used except as authorised by contract or other written permission. 6. This equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by ACC Communications. 7. Prerequisite skills: Personnel installing, commissioning, and maintaining the Airspan products must have a basic knowledge of telephony and radio communications, and have experience in installing, commissioning and maintaining telecommunications products. ACC provides a range of comprehensive training courses specifically aimed at providing operators/users of AS4000 products with the prerequisite skills to install, commission and or maintain the product. The courses can be tailored to provide the level of training required by the operator/user. 8. Airspan and Sitespan are Registered Trademarks of Airspan Communications Corporation. For additional information on Airspan Systems, please call your ACC Representative, or contact ACC at: Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Call (44) 1784 886700 AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 4 of 8 This Page Intentionally Blank AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 5 of 8 Safety Instructions - Warnings and Cautions SAFETY 1. Read and follow all warning notices and instructions marked on the product or included in this manual 2. Do not allow anything to rest on any power cord and do not locate the product where persons could step or walk on a power cord. 3. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. 4. No hazardous RF radiation is emitted from the equipment. Measured at the surface of the CRU radome, when transmitting, the maximum total power radiated from the CRU is 0.a1% of the UK National Radiological Protection Board basic restriction per kg. of body part. WARNING - HAZARDOUS VOLTAGES On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power. Remove metal jewellery that could come into contact with AC power. On DC sections, short circuiting the low voltage, low impedance circuits can cause severe arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits. Electro-Static Discharge ESD Electro-Static Discharge. Many circuits contain devices that are susceptible to damage from high impedance voltage sources. To avoid such risks always follow anti-static procedures where marked. AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 6 of 8 NOTE AS4000 products do not contain hazardous substances (as defined in UK ‘Control of Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances Regulations 1990’). At the end of any Airspan product’s life cycle, the customer should consult with Airspan to ensure that the product is disposed of in conformance with the relevant regulatory requirements The Symbol on an Airspan product signifies that it has been certified according to the EMC directive 89/336/EEC. The product fulfils the requirements according to the following standards: EN50082-1Immunity. EN55022 Group 1 Class A for the Central Terminal Emissions. EN55022 Group 1 Class B for the Subscriber Terminal Emissions. NOTE The Subscriber Terminal equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 7 of 8 User Response Form Mail: Airspan Communications LimitedFax: (44) 01895-467182 Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Document RatingExcellentGoodAverageBelow AveragePoor Accuracy / Completenessqqqqq Clarity / Organisationqqqqq Figuresqqqqq Table of Contents/Indexqqqqq The nature of this response isAddition qDeletion qCorrection q Please enter details of response below (include precise reference to Section, Page, Paragraph) Please complete the following for acknowledgement/response: Name:........................................Address.......................................... Company.................................................................................. Job Title.................................................................................. Department.................................................................................. Telephone.................................................................................. Thank you for your co-operation and assistance. AS4000 Access Concentrator Installation and Commissioning Preface 605-0000-453 Issue 1.2dr Date 7/02/00 Page 8 of 8 This Page Intentionally Blank AS4000 Access Concentrator Installation and Commissioning ICL 001 605-0000-453 Issue 1.2dr Date 7/02/00 Page 1 of 2© Copyright Airspan Communications Corporation 2000 ISSUE CONTROL LIST TitleIssueDateIssue Details Title Page1.2August 2000 ICL-0011.2August 2000 IXL-0011.2August 2000 GSI-0011.2August 2000 GSI-0021.2August 200…

Text truncated - open the document above for the full version.

605-0000-452Issue 1.3dr Date 7/02/00 AS4000 Wireless Local Loop System Demand Assignment Central Terminal Installation and Commissioning AS4000 Central Terminal Installation and Commissioning Preface 605-0000-452 Issue 1.3dr Date 7/02/00 Page 2 of 8 This Page Intentionally Blank AS4000 Central Terminal Installation and Commissioning Preface 605-0000-452 Issue 1.3dr Date 7/02/00 Page 3 of 8 Notice 1. This manual is subject to revision. 2. All rights reserved. 3. Right of modification reserved. 4. This manual is supplied without liability for errors or omissions. 5. No part of this manual may be reproduced or used except as authorised by contract or other written permission. 6. This equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by ACC Communications 7. Prerequisite skills: Personnel installing, commissioning, and maintaining the Airspan products must have a basic knowledge of telephony and radio communications, and have experience in installing, commissioning and maintaining telecommunications products. ACC provides a range of comprehensive training courses specifically aimed at providing operators/users of Airspan products with the prerequisite skills to install, commission and or maintain the product. The courses can be tailored to provide the level of training required by the operator/user. 8. Airspan and Sitespan are Registered Trademarks of Airspan Communications Corporation. For additional information on Airspan Systems, please call your ACC Representative, or contact ACC at: Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Call (44) 1784 886700 AS4000 Central Terminal Installation and Commissioning Preface 605-0000-452 Issue 1.3dr Date 7/02/00 Page 4 of 8 This Page Intentionally Blank AS4000 Central Terminal Installation and Commissioning Preface 605-0000-452 Issue 1.3dr Date 7/02/00 Page 5 of 8 Safety Instructions - Warnings and Cautions SAFETY 1. Read and follow all warning notices and instructions marked on the product or included in this manual 2. Do not allow anything to rest on any power cord and do not locate the product where persons could step or walk on a power cord. 3. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. 4. No hazardous RF radiation is emitted from the equipment. Measured at the surface of the CRU radome, when transmitting, the maximum total power radiated from the CRU is 0.01% of the UK National Radiological Protection Board basic restriction per kg. of body part. WARNING - HAZARDOUS VOLTAGES On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power. Remove metal jewellery that could come into contact with AC power. On DC sections, short circuiting the low voltage, low impedance circuits can cause severe arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits. Electro-Static Discharge ESD Electro-Static Discharge. Many circuits contain devices which are susceptible to damage from high impedance voltage sources. To avoid such risks always follow anti-static procedures where marked. AS4000 Central Terminal Installation and Commissioning Preface 605-0000-452 Issue 1.3dr Date 7/02/00 Page 6 of 8 NOTE Airspan products do not contain hazardous substances (as defined in UK ‘Control of Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances Regulations 1990’). At the end of any Airspan product’s life cycle, the customer should consult with DSC to ensure that the product is disposed of in conformance with the relevant regulatory requirements The Symbol on an Airspan product signifies that it has been certified according to the EMC directive 89/336/EEC. The product fulfils the requirements according to the following standards: EN50082-1for Immunity. EN55022 Group 1 Class A for the Central Terminal Emissions. EN55022 Group 1 Class B for the Subscriber Terminal Emissions. NOTE The Subscriber Terminal equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. CAUTION PA INSERTION Care should be taken when installing PAs to ensure that the card connector mates with the backplane connector correctly. Any attempt to ram the card home or force the card into he slot may cause damage to the connector. Insert the card until the connectors engage, ease the card into the backplane until fully engaged. Lock top and bottom with a screwdriver. If resistance is met remove the card and reinsert. If difficulty persists contact the Airspan service centre. CAUTION DIP/LNA INSERTION Care should be taken when installing DIP/LNAs to ensure that the card connector mates with the backplane connector correctly. Any attempt to ram the card home or force the card into he slot may cause damage to the connector. The board extractor levers mat be used to assist with insertion, when the card is home press the body of the DIP/LNA to ensure that the connector is fully engaged. If resistance is met remove the card and reinsert. If difficulty persists contact the Airspan service centre AS4000 Central Terminal Installation and Commissioning Preface 605-0000-452 Issue 1.3dr Date 7/02/00 Page 7 of 8 User Response Form Mail: Airspan Communications Limited Fax: (44) 01895-467182 Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Document RatingExcellentGoodAverageBelow AveragePoor Accuracy / Completenessqqqqq Clarity / Organisationqqqqq Figuresqqqqq Table of Contents/Indexqqqqq The nature of this response isAddition qDeletion qCorrection q Please enter details of response below (include precise reference to Section, Page, Paragraph) Please Complete the following for acknowledge…

Text truncated - open the document above for the full version.

605-0000-455 Issue 2.0 21/03/00© Copyright Airspan 2000 AS4000 Wireless Local Loop System DA Central Terminal Commissioning Unit Operators Manual AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Page 2 of 28 This Page Intentionally Blank AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Page 3 of 28 Notice 1. This manual is subject to revision. 2. All rights reserved. 3. Right of modification reserved. 4. This manual is supplied without liability for errors or omissions. 5. No part of this manual may be reproduced or used except as authorised by contract or other written permission. 6. This equipment is conditioned by the requirement that no modifications are made to the equipment unless the changes or modifications are expressly approved by the Airspan Communications Corporation 7. Prerequisite skills: Personnel installing, commissioning, and maintaining the Airspan products must have a basic knowledge of telephony and radio communications, and have experience in installing, commissioning and maintaining telecommunications products. Airspan provides a range of comprehensive training courses specifically aimed at providing operators/users of Airspan products with the prerequisite skills to install, commission and or maintain the product. The courses are tailored to provide the level of training required by the operator/user. 8. AS4000 and AS8100 are brands of Airspan Networks Inc For additional information on Airspan Systems, please call your Airspan Representative, or contact Airspan at: Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Call (44) 895 4677100 Fax (44) 895 4677101 email sales@ airspan.com AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Page 4 of 28 This Page Intentionally Blank AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Page 5 of 28 Safety Instructions - Warnings and Cautions SAFETY 1. Read and follow all warning notices and instructions marked on the product or included in this manual 2. Do not allow anything to rest on the power cord and do not locate the product where persons could step or walk on the power cord. 3. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. 4. No hazardous RF radiation is emitted from the equipment. WARNING - HAZARDOUS VOLTAGES On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power. Remove metal jewellery that could come into contact with AC power. On DC sections, short circuiting the low voltage, low impedance circuits can cause severe arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits. Electro-Static Discharge ESD Electro-Static Discharge. Many circuits contain devices which are susceptible to damage from high impedance voltage sources. To avoid such risks always follow anti-static procedures where marked. AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Page 6 of 28 NOTE Airspan products do not contain hazardous substances (as defined in UK ‘Control of Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances Regulations 1990’). At the end of any Airspan product’s life cycle, the customer should consult with Airspan to ensure that the product is disposed of in conformance with the relevant regulatory requirements The Symbol on an Airspan product signifies that it has been certified according to the EMC directive 89/336/EEC. The product fulfils the requirements according to the following standards: EN50082-1for Immunity. EN55022 Group 1 Class A for the Central Terminal Emissions. EN55022 Group 1 Class B for the Subscriber Terminal Emissions. NOTE The Subscriber Terminal equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. AS4000 DA CT Commissioning Unit Operators Manual IXL 001 605-0000-455 Issue 2.0 Date 21/03/00 Page 7 of 28© Copyright Airspan 2000 INDEX TASK LIST PREFACE: Safety Instructions Warnings and Cautions Index Task List....................................................................................................IXL-001 GENERAL SYSTEM INFORMATION: GSI Introduction..........................................................................................................GSI-001 1.Purpose of Document..............................................................................................9 2.Prerequisite skills....................................................................................................9 DA Commissioning Unit......................................................................................GSI-002 1.Introduction..........................................................................................................11 2.DACU Components..............................................................................................11 3.Architecture Overview..........................................................................................11 4.Principles of Operation.........................................................................................11 5.DA Commissioning Unit.......................................................................................13 5.1.Mechanical........................................................................................................13 5.2.RF Interconnect................................................................................................14 5.3.Power Meter Connections.................................................................................14 5.4.Shelf Controller Communication…

Text truncated - open the document above for the full version.

605-0000-450Draft Issue 1.3dr Date 8/02/00 AS4000 Wireless Local Loop System Demand Assignment System Overview Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 2 of 10 Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 3 of 10 Notice 1. This manual is subject to revision. 2. All rights reserved. 3. Right of modification reserved. 4. This manual is supplied without liability for errors or omissions. 5. No part of this manual may be reproduced or used except as authorised by contract or other written permission. 6. This equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by ACC Communications 7. Prerequisite skills: Personnel installing, commissioning, and maintaining the AS4000 products must have a basic knowledge of telephony and radio communications, and have experience in installing, commissioning and maintaining telecommunications products. ACC provides a range of comprehensive training courses specifically aimed at providing operators/users of Airspan products with the prerequisite skills to install, commission and or maintain the product. The courses can be tailored to provide the level of training required by the operator/user. 8. Airspan and Sitespan are Registered Trademarks of Airspan Communications Corporation. For additional information on Airspan Systems, please call your ACC Representative, or contact ACC at: Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Call (44) 1895 467100 Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 4 of 10 This Page Intentionally Blank Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 5 of 10 Safety Instructions - Warnings and Cautions SAFETY 1. Read and follow all warning notices and instructions marked on the product or included in this manual 2. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. WARNING - HAZARDOUS VOLTAGES On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power. Remove metal jewellery that could come into contact with AC power. On DC sections, short circuiting the low voltage, low impedance circuits can cause severe arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits. Electro-Static Discharge ESD Electro-Static Discharge. Many circuits contain devices which are susceptible to damage from high impedance voltage sources. To avoid such risks always follow anti-static procedures where marked. NOTE Airspan products do not contain hazardous substances (as defined in UK ‘Control of Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances Regulations 1990’). At the end of any Airspan product’s life cycle, the customer should consult with ACC to ensure that the product is disposed of in conformance with the relevant regulatory requirements Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 6 of 10 The Symbol on an Airspan product signifies that it has been certified according to the EMC directive 89/336/EEC. The product fulfils the requirements according to the following standards: EN50082-1for Immunity. EN55022 Group 1 Class A for the Central Terminal Emissions. EN55022 Group 1 Class B for the Subscriber Terminal Emissions. Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 7 of 10 User Response Form Mail: Airspan Communications Limited Fax: (44) 1895 467182 Cambridge House Oxford Road Uxbridge Middlesex UB8 1UN Document RatingExcellentGoodAverageBelow AveragePoor Accuracy / Completenessqqqqq Clarity / Organisationqqqqq Figuresqqqqq Table of Contents/Indexqqqqq The nature of this response isAddition qDeletion qCorrection q Please enter details of response below (include precise reference to Section, Page, Paragraph) Please Complete the following for acknowledgement/response: Name:........................................Address.......................................... Company.................................................................................. Job Title.................................................................................. Department.................................................................................. Telephone.................................................................................. Thank you for your co-operation and assistance. Demand Assignment System OverviewPreface 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 8 of 10 This Page Intentionally Blank Demand Assignment System OverviewICL 001 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 1 of 2© Copyright Airspan Communications Corporation 1998 ISSUE CONTROL LIST TitleIssueDateIssue Details Title Page13drFebruary 2000Update ICL-00113drFebruary 2000Update IXL-00113drFebruary 2000Update GSI-00113drFebruary 2000Update GSI-00213drFebruary 2000Update GSI-00313drFebruary 2000Update GSI-00413drFebruary 2000Update GSI-00513drFebruary 2000Update GSI-00613drFebruary 2000Update Appendix A13drFebruary 2000Update Demand Assignment System OverviewICL 001 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 2 of 2 CHANGE TYPE/DATEPURPOSEPAGES AFFECTED Issue #, Month Year 1.0, June 1998Initial DocumentAll 1.1, May 1999Updates to all sectionsAll 1.2, November 1999Delete ST-V2, delete LCU, add Modular 1.3dr February 2000Update to frequency plansAppendix 2 Demand Assignment System OverviewIXL 001 605-0000-450 Draft Issue 1.3dr Date 8/02/00 Page 1 of 6© Copyright Airspan Communications Corporation 1998 INDEX TASK LIST PREFACE: Safety Instructions Warnings and Cautions…

Text truncated - open the document above for the full version.