O44JR1700A433Car Alarm System

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. YOUNGSHIN Electronic Co.,Ltd. USER’S GUIDE YOUNGSHIN Electronic Co.,Ltd. R1700-AM FCC ID : O44JR1700A433 USER’S GUIDE One-Way AM Remote R 1 7 0 0 - A M FCC ID : 044JR1700A433 Page 2Page 3 TABLE OF CONTENTS -Safety Information -Remote : R1700-AM -Remote Button Functions -Remote Learn Routine -Keyless Entry -Alarm Mode -Auto-Start Function -Reservation Mode - Trunk Release -Panic Mode -Valet Mode -Timer Start Mode -Safety Shut Down Features -Optional Programmable Features Ignition Lock Passive Locking Turbo Mode -Optional Installation Features Cold Start Mode Optional Auxiliary 1& Auxiliary 2 -Limited Lifetime Consumer Warranty Page 4 Page 4 Page 5 Page 5 Page 6 Page 6 Page 7 Page 8 Page 9 Page 9 Page 10 Page 10 Page 11 Page 11 Page 11 Page 11 Page 12 Page 12 Page 12 Page 13 Page 12 R1700-AM is a One Way AM 4 Button Remote. Safety Information Please take these safety precautions into consideration under the following conditions : Under normal circumstances, Reservation Mode is cancelled when a door or hatchback opens. Please verify that the opening of any door or hatchback cancels Reservation Mode. If any of the doors or hatchback are not monitored by CompuStar because of improper installation or a faulty dome light switch, do not use the CompuStar and take your vehicle immediately to the dealer for repair. Do not set Reservation Mode if the window(s) are open or if there is anyone inside the vehicle, this includes animals. Remote start installation in a manual transmission vehicle with a convertible top is not recommended. Page 4 I m p o r t a n t ! 1. Servicing the vehicle When servicing your automobile (i.e. changing the oil, washing your car), the CompuStar system should be in Valet Mode. There is a safety shutdown switch under the hood that deactivates the remote starter function if the hood is open. However, if the switch has been damaged or the switch has been installed improperly, the vehicle may start when the button is pressed for 2 seconds, even if the hood is open. 2. Loaning your vehicle to others Whenever you loan your vehicle to an individual who is not familiar with Compustar, you may want to put the vehicle in Valet mode. This will prevent the borrower from acci- dentally activating the CompuStar auto-security system. 3. For manual transmission vehicles If the Compustar R1700-AM is installed in a manual transmission vehicle, extra precautions are required because the Compustar does not monitor the gear shift : Remote : R1700-AM Page 5 Remote Button Functions 1 2 3 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 ButtonPressFunction 0.5 sec Horn - on/off 0.5 secValet Mode - on/off 0.5 sec Passive Locking - on/off 0.5 sec 0.5 sec Timer Start Mode - on/off Turbo Mode - on/off 2 sec Programming Menu 1- Installer Only 2 secProgramming Menu 2- Installer Only Note : " "Means, to press the button for 2 seconds. "()"Means, to simultaneously pressing the buttons. "() "Means, to simultaneously press the buttons for 2 seconds . 4 Lock. If held for 3.5 seconds, it will panic the system.0.5 sec 0.5 sec 0.5 sec 0.5 sec Unlock 2 secAuto -start Function - on/off Auxiliary Option 2 Auxiliary Option 1 2 secTrunk Release 3.5 sec Panic, Press to shut off. Remote Learn Routine The Compustar system will allow up to three remotes to be programmed to one vehicle. Please perform the following procedure to add or reprogram additional remotes. Page 7 Auto-Start Function Press the button for 2 seconds to auto-start an automatic transmission engine. Remember, that an actual key in the ignition is required to drive the car. For manual transmission vehicles, please use reservation mode. Press the button for 2 seconds in order to turn off an auto-started car. The engine will run 15 or 25 minutes (25 or 45 min for diesel) depending on preset options at the time of installation, and then shut off. 1 2 3 4 5 6 7 Error Number (# of times the car chirps & parking lights flash) Error Reason Engine On Key On Door Open Trunk Open Brake On Hood Open Reservation Off (Manual Transmission Only) Diagnosing problems with Auto-Start If there is a problem in auto-starting your vehicle,the CompuStar system will do one of two things; if it fails for any of the reasons listed in the table below, it will flash the parkinglights three times then flash the error number. Otherwise, it will attempt to start the vehicle three times. If, after three times, the vehicle will not start or stay running, the CompuStar system will shut down. In either case, please see your istaller to resolve the situation. Key less Entry Alarm Mode Page 6 Step2 :Within a 7 second period after cycling the ignition for the 5 th time, Press the button for a 1/2 sec. The car parking lights will flash once to confirm that the transmitter has been programmed. You can continue programming additional remotes. The parking lights will flash two times when the programming mode has expired. To lock the vehicle, press the button for 0.5 seconds. To unlock the vehicle, press the button for 0.5 seconds. If the pressing of the lock/unlock buttons does not lock/unlock the doors, you will need to release the but- ton and try again, as the remote stops transmitting as soon as the LED stops flash- ing. If the button is pressed for 3.5 seconds, it will panic the system. To arm the vehicle, press the buttonuntil the LED on the remote stops flashing. To disarm the vehicle, press the buttonuntil the LED on the remote stops flashing. If pressing the arm/disarm buttons does not arm/disarm the vehicle, you will need to release the button and try again, as the remote stops tr…

Text truncated - open the document above for the full version.

–

’

KTL Korea Testing Laboratory Page 1 of 14 TEST REPORT This test report only responds to the tested sample and shall not be reproduced except in full without written approval of the Korea Testing Laboratory. Tested and reported by Reviewed by Jeong-Min Kim, Senior Engineer Won-Seo Cho , Telecommunication Team Manager KOREA TESTING LABORATORY FG101-01-02-00 222-13, Guro-Dong Guro-Gu Seoul Korea 152-053 http://www.ktl.re.kr Ref. Report No. 04-1341-023 Name and address of the applicant Youngshin Electronic Co., Ltd. 102-701, Bucheon Techno-park 364 Smajeong-dong, Ojeong-gu, Bucheon-si, Gyeonggi-do, 421-740 Korea Standard / Test regulation FCC Part 15, Subpart C Test result Pass Incoming date : August 16, 2004 Test item(s) ; Security/Remote Control Transmitter (Car Alarm System) Model/type ref. ; R1700-AM Manufacturer ; Youngshin Electronic Co., Ltd. Additional information ; -Required Authorization : Certification -FCC ID. : O44JR1700A433 Test date : September 20, 2004 Issue date : September 23, 2004 Ref. Report No. 04 - 1341 – 023 Page 2 of 14 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 TABLE OF CONTENTS I. GENERAL INFORMATION 3 1. Grantee’s Name and Mailing Address 2. Manufacturer's Name and Mailing Address 3. Equipment Descriptions 4. Rules and Regulations 5. Measuring Procedure 6. Place of Measurement 7. Date of Measurement . GENERAL REQUIREMENTS OF THE EUT 4 1. Labeling Requirement (Section 15.19) 2. Information to User (Sections 15.21) 3. Special Accessories (Section 15.27) 4. Compliant Conditions (Section 15.231) . RADIATED EMISSION MEASUREMENT (Section 15.231) 6 1. Test Procedure 2. Photograph of the test configuration 3. Sample Calculation 4. Measurement Data . OCCUPIED BANDWIDTH MEASUREMENT (Section 15.231) 13 . TEST EQUIPMENTS USED FOR MEASUREMENT 14 Ref. Report No. 04 - 1341 – 023 Page 3 of 14 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 . GENERAL INFORMATION 1. Grantee’s Name and : YoungShin Electronics Co., Ltd. Mailing Address 102-701, Bucheon Techno-park, 364, Samjeong-dong, Ojeong-gu, Bucheon-si, Kyungki-Do, 421-740 Korea 2. Manufacturer's Name and : YoungShin Electronics Co., Ltd. Mailing Address 102-701, Bucheon Techno-park, 364, Samjeong-dong, Ojeong-gu, Bucheon-si, Kyungki-Do, 421-740 Korea 3. Equipment Descriptions 3.1 Operating Frequency : 433.92 MHz 3.2 Type of Emission : Pulse Code Signal 3.3 Power Supply : DC 6 V (Battery) 4. Rules and Regulations : FCC Part 15, Subpart C 5. Measuring Procedure : ANSI C63.4-2001 6. Place of Measurement : Absorber-lined Room (KTL) 7. Date of Measurement 7.1 Conducted Emission : Not Applicable 7.2 Radiated Emission : September 20, 2004 Ref. Report No. 04 - 1341 – 023 Page 4 of 14 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 . GENERAL REQUIREMENTS OF THE EUT 1. Labeling Requirement (Section 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1.1 Location of Label : User’s Guide Manual 1.2 How Applied : Printed 2. Information to User (Section 15.21) The following or similar statements were provided in the manual for user instruction. Please refer page 1 of the attached manual for details. CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3. Special Accessories (Section 15.27) 3.1 Were the special Accessories provided? [ ] yes, [ x ] no 3.2 If yes, details for the special accessories are as follows : 3.3 If yes, were the appropriate instructions provided on the first page of the text concerned with the installation of the device? [ ] yes, [ ] no 3.4 Are these accessories provided of the type which can be readily obtained from multiple retail outlets ? [ ] yes, [ ] no And therefore does the manual specify what additional components or accessories are required to used in order to comply with the Rules? [ ] yes, [ ] no Ref. Report No. 04 - 1341 – 023 Page 5 of 14 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 4. Compliant Conditions (Section 15.231) 4.1 Was the EUT used for continuous transmissions, such as voice or video, and data transmission ? [ ] yes, [ x ] no 4.2 Was the EUT manually operated ? [ x ] yes, [ ] no If yes, did the EUT employ a switch that would automatically deactivate the transmitter within not more than 5 seconds of being released ? [ x ] yes, [ ] no 4.3 Was the EUT automatically activated ? [ ] yes, [ x ] no If yes, did the EUT cease transmission within 5 seconds after deactivation ? [ ] yes, [ ] no 4.4 Was the EUT used for periodic transmissions at regular predetermined intervals ? [ ] yes, [ x ] no Ref. Report No. 04 - 1341 – 023 Page 6 of 14 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 . RADIATED EMISSION MEASUREMENT (Section 15.231) 1. Test Procedure 1.1 Preliminary Testing for Reference Preliminary testing was performed in a KTL absorber-lined room to determine the emission characteristics of the EUT. The EUT was placed on the wooden table which has dimensions of 0.8 meters in height, 1 meter in length and 1.5 meters in width. Receiving antenna (Biconi-Log antenna : 30 to 1000 MHz or Horn Antenna : 1 to 18 GHz) was placed at the distance of 1 meter from the EUT. An attempt was made to maximize the emission level with the various configurations of the EUT. Emission levels from the EUT with various configurations were examined on a spectrum analyzer connected with a RF amplifier and graphed by a plotter. 1.2 Final Radiated Emission Test at an Absorber-Lined Room The final measurement …

Text truncated - open the document above for the full version.

Ref. Report No. 04 - 1341 – 023 Page 7 of 14 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 2. Photograph of the test configuration 3. Sample Calculation The measured field strength was determined by averaging one complete pulse train including blanking interval because the pulse repetition time of the EUT(=51.0 ms) does not exceeds 0.1 seconds (15.35(c)). See graphs of page 12 . With the resolution bandwidth set at 100 kHz, the EUT produces a pulse spectrum on the spectrum analyzer because the bandwidth of the analyzer is greater than or equal to the PRF (=1428 Hz). Therefore, as mentioned in HP Application Note 150-2 (page 11), the pulse desensitization(a p ) equals zero and the display amplitude is essentially a peak level. .