O9DAP4Wireless Step Sensor/Pedometer

There are two important things to remember when putting on your ActiPed. 1. It must be located on the top of your shoe between your toes and the front of your ankle. 2. It must be snug to your shoe and not loose where it can move or flop around. For sneakers or shoes with laces, slide the ActiPed clip underneath 2 or 3 lace crossings and place the ActiPed TM near the top middle of your shoe. For shoes without laces, slide the clip underneath a strap, the tongue or anyplace that is on top of the shoe that the clip can snugly grip to. What does the ActiPed collect for your activity? The ActiPed TM collects activity data as steps, activity time, calories burned and distance traveled. It measures activity data for your run steps, walk steps or moving around. It does not work for all types of activities, the ones primarily where your foot isn’t hitting the ground in a manner that could be considered a verifiable foot strike. For example, elliptical machines and cycling. The ActiPed TM will store approximately 10 to 30 days of activity data depending on how much you wear you ActiPed and your daily activity levels. How does my activity data get transferred from my ActiPed to my personal web account? The ActiPed TM wirelessly transports your activity data when it contacts an ActiLink data access device. This can be through either an ActiLink Personal USB device in your computer or other ActiLink devices set up in a building, facility or worksite. Need Help or Answers to Questions? through the Frequently asked Questions or Email us at Additional Information (Specifications): Battery Type: CR2032 Lithium 3V – non replaceable battery Water Resistant: Non Submersible Operating Temperature: 14F to 104F Storage Temperature: -4F to 122F Limited Warranty TM warranty does not cover normal wear, damage, loss or commercial use. The Authorized Technician. For any warranty claims please contact your plan administrator. THE FORGOING IS YOUR SOLE REMEDY UNDER THIS LIMITED WARRANTY. IN NO EVENT WILL FITSENSE TECHNOLOGY INC. BE LIABLE FOR ANY INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF ABILITY TO USE THE PRODUCT EVEN IF FITSENSE HAS BEEN ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Disclaimer physician before beginning any exercise program or performing strenuous Regulatory Information Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference Patents The ActiPed is covered in whole or in part by the following patents: 6,336,365; 6,018,705; 6,052,654; 6,493,652; 6,298,314; 6,122,340; 6,357,147; 6,536,139; 6,560,903; 6,611,789; 6,882,955; 6,876,947 and other patents pending. FCC ID: O9DAP4 This device complies with Part 15 of the FCC Rules. received, including interference that may cause undesired operation. The ActiPed is warranted against defects in material and workmanship for The ActiPed is not a medical device. This device is provided for feedback on How to put on your ActiPed+ on your footwear? [email protected]. user’s authority to operate the equipment. Changes or modifications not expressly approved by Fitlinxx could void the one year after purchase. Defective products will be repaired or replaced. The exercise and routine activity only. FitLinxx recommends that you consult a For Help: Go to www.fitlinxx.com click on Help and then look warranty is void if the unit is disassembled by anyone other than a FitLinxx activity.

.20 .40 Black Font on Silver background Dimensioned With Border Scaled 8:1 100% Text With Border Scaled 8:1 100% Text Scaled 8:1 02 06-27-09 -J MacLean Nylon or Equivalent ± 0.1 mm 2 PLACE DECIMAL ± 1.0 ± 1.0 mm ± 0.25 mm 1 PLACE DECIMAL ANGULAR TOL'S 0 PLACE DECIMAL ASME Y14.5M-1994 APPLIES SURFACE FINISH: 3.2 CHK'D DATE DSN'D DRAWN 21 Boston Road PO Box 730 Southborough, MA 01772 Phone: 508.303.8811 Fax:508.357.7990 DATE CHK'D DRAWN MAT'L DRAWING NUMBER PAPER SIZE DSN'D Rev Date Description Init ECN REV Drawn by SolidWorks - SHEET 1 OF 1 214-00077-01 This document contains confidential or proprietary information of FitSense, Inc. Neither this document nor the information therein is to be reproduced, distributed, used or disclosed either in whole or in part, except as specifically authorized by FitSense, Inc. EXCEPT AS NOTED, ALL DIMS ARE MM DIMENSIONS IN [ ] ARE INCHES μ m LABEL, CHINA IC, ACTIPED 4.1 T Boudreau B SCALE:8:1

Page 2 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Tests Performed The test methods performed on the ActiPed+ (Step Sensor/Pedometer) Transceiver are shown below: FCC Part 15, Subpart C Industry Canada RSS-210 Issue 8, December 2010 Industry Canada RSS-Gen Issue 3, December 2010 Test Method 15.249(a)(e) A2.9 (a) N/A Field Strength of Fundamental & Harmonic Emissions 15.249(d) A2.9(b) N/A Field Strength of Out of Band/Bandedge Spurious Emissions N/A N/A 7.2.3 Receiver Spurious Radiated Emissions N/A N/A 4.6.1 99% Bandwidth General Test Requirements 1. The measurement procedures of ANSI C63.4:2003 were utilized as specified in FCC Part 15, Subpart C, Section 15.31(a)(3) and RSS-Gen, Section 4.1. 2. All radiated emissions measurements were performed on an Open Area Test Site (OATS), listed with the FCC and IC, in accordance with FCC Section 15.31(d) and RSS Gen, Section 4.2. 3. All testing was performed with a new battery installed in the EUT, in accordance with FCC Section 15.31(e) and RSS Gen Section 4.3(g). 4. All measurements were performed at the specified 3 meter test distance. The EUT was rotated throughout 360 degrees for all radiated emissions measurements as specified in FCC Section 15.31(f)(5) and IC Section 4.3(h). 5. All readily accessible EUT controls were adjusted in such a manner as to maximize the level of emissions in accordance with FCC Section 15.31(g) and RSS-Gen, Section 4.3. 6. Appropriate accessories were attached to all EUT ports during the performance of radiated emissions measurements as required by FCC Section 15.31(i) and RSS-Gen, Section 4.3(f). 7. The EUT operated at the frequency of 2429.0 MHz. Testing was performed with the device operating at this frequency. 8. The frequency spectrum was investigated from the lowest frequency generated in the device up to the 10 th harmonic of the highest fundamental frequency in accordance with FCC Section 15.33(a)(1) and RSS-Gen Section 4.9. 9. Measurements below 1000 MHz were taken utilizing a Quasi-Peak Detector. Measurements above 1 GHz were taken utilizing an Average Detector in accordance with FCC Section 15.35(a) and IC Section 4.9. The peak value of emissions above 1 GHz were verified to meet the 20 dB requirement of FCC Section 15.35(b). Page 3 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Certification and Signatures We certify that this report is a true representation of the results obtained from the tests of the equipment stated. We further certify that the measurements shown in this report were made in accordance with the procedures indicated and vouch for the qualifications of all Retlif Testing Laboratories personnel taking them. Scott Wentworth Branch Manager NVLAP Approved Signatory Todd Hannemann Laboratory Supervisor iNARTE Approved ATL-0255-T Non-Warranty Provision The testing services have been performed, findings obtained and reports prepared in accordance with generally accepted laboratory principles and practices. This warranty is in lieu of all others, either expressed or implied. Non-Endorsement This test report contains only findings and results arrived at after employing the specific test procedures and standards listed herein. It is not intended to constitute a recommendation, endorsement or certification of the product or material tested. This test report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Page 4 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Requirements and Test Results Requirement: FCC Section 15.249(a) and (d) - Operation within the bands 902 - 928 MHz, 2400 - 2483.5 MHz, 5725 - 5875 MHz and 24.0 - 24.25 GHz IC RSS-210, A2.9(a) and (b): This section provides standards for low-power devices that can be used for any application provided the following condition is met: FCC Section 15.249(a): Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with Table 1. RSS-210 A2.9(a): The field strengths measured at 3 meters shall not exceed the limits specified in Table 1. Table 1 - Field Strength of Emissions Fundamental Frequency Field Strength - Fundamental (millivolts/meter) Field Strength - Harmonics (microvolts/meter) 902 to 928 MHz 50 500 2400 to 2483.5 MHz 50 500 5725 to 5875 50 500 24.0 to 24.25 GHz 250 2500 • Results: The EUT was operated at 2429.0 MHz. The field strength of the fundamental did not exceed 50 mV/M. The field strength of the harmonics did not exceed 500 μV/M. FCC Section 15.249(d): Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. RSS-210 A2.9(b): Emissions radiated outside of the frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general field strength limits of RSS-Gen, Table 5 , whichever is the less stringent. • Results: Emissions radiated at the band edges and outside the specified frequency band were attenuated in accordance with the general radiated emissions limits of 15.209 and RSS-Gen, Table 5. Page 5 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Requirements and Test Results (con’t) Requirement: RSS-GEN, 7.2.3 - Receiver Spurious Emission Limits All spurious emissions shall comply with the limits specified in Table 2. Table 2 - Radiated Emission Limits Frequency of Emission (MHz) Field Strength (microvolts/meter) 30 to 88 100 88 to 216 150 216 to 960 200 Above 960 500 • Results: The emissions observed did not exceed the limits specified in Table 2. Page 6 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC I…

Text truncated - open the document above for the full version.

Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Test Setup Horizontal Antenna Polarization, 1 to 18 GHz Page 10 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 1 to 18 GHz Horizontal Antenna Polarization, 18 to 26 GHz Page 11 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 18 to 26 GHz Page 12 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 FCC Section 15.249(d) and RSS-210, A2.9(b) Field Strength of Out of Band Spurious Emissions Photographs Page 13 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Test Setup Horizontal Antenna Polarization, 30 to 1000 MHz Page 14 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 30 to 1000 MHz Horizontal Antenna Polarization, 1 to 18 GHz Page 15 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 1 to 18 GHz Horizontal Antenna Polarization, 18 to 26 GHz Page 16 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 18 to 26 GHz Page 17 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 FCC Section 15.249(d) and RSS-210, A2.9(b) Field Strength of Band Edge Emissions Photographs Page 18 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Test Setup Horizontal Antenna Polarization, 1 to 18 GHz Page 19 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 1 to 18 GHz Page 20 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 RSS-GEN, 7.2.3 - Receiver Spurious Emission Photographs Page 21 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Test Setup Horizontal Antenna Polarization, 30 to 1000 MHz Page 22 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 30 to 1000 MHz Horizontal Antenna Polarization, 1 to 18 GHz Page 23 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 1 to 18 GHz Horizontal Antenna Polarization, 18 to 26 GHz Page 24 of 34 Retlif Testing Laboratories, Test Report R-5351N, FitLinxx FCC ID: O9DAP4, IC: 4068A-AP4 Vertical Antenna Polarization, 18 to 26 GHz Page 25 of 34