OBDT-39-40-41-315Remote Control Transmitter

1 PORTMAN CAR ALARM TRANSMITTER – 3-BUTTON ButtonFunctionsConditions 1a. Arm and lock doors b. Car finder with sound c. Temporary stop alarm from sounding d. Remote lock doors Alarm is disarmed Alarm is being armed Alarm is sounding While driving 2a. Disarm b. Remote unlock doors c. Stop alarm from sounding Alarm is being armed While driving Alarm is sounding 2 for 2 secSecond unlockAlarm is disarmed 3a. Silent arm b. Car finder without sound c. Anti car-hijacking Alarm is disarmed Alarm is being armed While driving 3 for 2 secLeave anti car-hijackingWhile in anti car-hijacking 1+2PanicAnytime 2+3Open trunk or Engine startIgnition is OFF Remark: a. Please refer the above table and the following operating instructions for all function. b. Use Hopping code for transmission. T40 FEATURES CODE LEARNING a. In disarm mode, turn ignition ON, press Valet Switch 10 times within 8 seconds, siren will chirp 3 times to enter code-learning mode. b. Press any button on the transmitter within 8 seconds. If over 8 sec or turn ignition OFF, the system will exit code-learning mode automatically. c. The siren will chirp accordingly for confirmation as soon as the code is learned. For example, the first transmitter is learned, the siren will chirp once. The second transmitter is learned, the siren will chirp twice. d. If one of the transmitters is to be programmed, the other transmitters must be reprogrammed at the same time. e. Up to 3 transmitters can be learned per module. ARMING a. Press button 1. b. Siren will chirp once or no chirp (See Function Selection 6). c. Parking light will flash once. d. Door will be locked at 0.5sec or 3.5 sec (See Function Selection 1). e. LED will flash slowly. If door is not closed, the siren will chirp 5 times for warning and LED flashes quickly. f. Disables engine starter if Interrupt (NC) Relay connected g. After 3 seconds, the system is armed. All the sensors are armed. If the alarm is triggered within 3 sec, the siren will chirp twice and the circuit is by-pass till the triggering source is stable. DISARMING a . Press button 2. b. Siren will chirp 3 times or has no chirp (See Function Selection 6). If siren chirps 4 times, it means the alarm has been activated. c. Parking lights will flash 3 times; if flash 4 times which indicates the alarm has been activated. After flashing, the dome light will keep ON 30 sec max or turn ignition ON the dome light is OFF. d. Doors will unlock at 0.5sec or 3.5sec (See Function Selection 1). e. LED is off and enables engine if Interrupt (NC) Relay connected. SILENT ARMING a. Press button 3. b. Parking light will flash once. c. Door will be locked at 0.5sec or 3.5 sec (See Function Selection 1). d. LED will flash slowly. If door is not closed, the siren will chirp 5 times for warning and LED flashes quickly. e. Disables engine starter if Interrupt (NC) Relay connected. f. After 3 seconds, the system is armed. All the sensors are armed. If the alarm is triggered within 3 sec, the siren will chirp twice and the circuit is bypassed till the triggering source is stable. EMERGENCY DISARMING – OVERRIDE (FACTORY PRESET VALUE: PRESS SWITCH 5 TIMES) a . Turn ignition ON. b. Press valet switch at set-up value (5 times), siren will chirp 4 times which indicates the system is disarmed. This process must be finished within 8 seconds. c. Replace Set-up Emergency Disarming value: (a) Turn ignition ON. After press valet switch 5 times within 8 sec. Siren chirp 4 times which indicates the system is in replace set-up mode (b) Press the numbers (1-15max) as the value you prefer within 8 sec. (If the number is over 15, the system will return back to the original set-up value) Then, siren will chirp the numbers replaced for confirmation. AUTOMATIC DOOR UNLOCK When the ignition turn from ON to OFF, doors will be automatically unlocked. AUTOMATIC DOOR LOCK (SEE FUNCTION SELECTION 4) When the ignition turn from OFF to ON, doors will be locked after 20 sec. VALET (SEE FUNCTION SELECTION 12) a . In disarm mode, turn ignition ON, within 8 sec press and hold valet switch 3 sec once. b. LED will be constantly ON after 8 sec or turn ignition OFF. c. In Valet mode: siren chirp twice and parking lights flash twice. d. Exit valet mode: Turn ignition ON, press and hold valet switch 3 sec once, LED will be OFF after 8 seconds or turn ignition OFF. e. In Valet mode, except arming function, the others remain the same. PANIC a Press button 1+2. The siren will sound, parking lights and dome light will flash for 30 seconds. b. Press any button to stop the panic. CAR FINDER a . The system is armed. b. Press button 1 : siren will chirp once, parking lights and dome light will flash 10 sec. c. Press button 3 : car finder in silent mode, parking lights and dome light will flash 10 sec. d. Press button 2 to stop car finder and disarm. ANTI CAR-HIJACKING (SEE FUNCTION SELECTION 7) a. When ignition is ON and the doors are closed, press the button 3 and open the door within 8 seconds to activate anti car-hijacking mode. If the door is not opened within 8 sec, the mode is exit. b. Close the door to start the 30 seconds countdown. The LED flashes quickly. c. When the 30 sec is up, siren will chirp every 2 sec. After 20 seconds, siren continuously, also parking lights will continuously flash. Siren will stop to sound & parking lights will stop to flash as long as the ignition turn OFF. After ignition is OFF, engine disables to start again (if interrupt (NC) relay connected). d. Disarm the anti car-hijacking: Press button 3 for two seconds. The parking lights will flash once for confirmation. 2-STAGE SHOCK SENSOR a . If car is lightly vibrated once, siren will sound for 5 chirps. If the car is vibrated again within 8 seconds, siren will sound and parking lights, dome light flash for 30 seconds. b. If car receives a heavy shock, siren will sound for 30 seconds and parking lights, dome light will flash for 30 seconds OPEN TRUNK OR ENGINE STARTER a. Press 2+3 (with 0.5 sec 300mA negative ou…

Text truncated - open the document above for the full version.

ETC Report No.: ET91S-12-105-05Page A1 of A1 FCC ID: OBDT-39-40-41-315 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Front view of EUT 2. Rear view of EUT

T39,T40,T41

ETC Report No.: ET91S-12-105-05Page B1 of B2 FCC ID: OBDT-39-40-41-315 ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside 1 of EUT 2. Front view of PCB ETC Report No.: ET91S-12-105-05Page B2 of B2 FCC ID: OBDT-39-40-41-315 3. Rear view of PCB

T40 Operate Description Button 1,2,3 (S1,2,3) are supplied DC power to Encode Circuit and decided U1 was sending the signal type, and the signal was through R2 to Oscillator step Q1 to Transmit RF signal .

FCC ID: OBDT-39-40-41-315 Rev. No 1.0 FCC Part 15 Subpart C TEST REPORT of E.U.T. : Car Alarm Transmitter FCC ID. : OBDT-39-40-41-315 MODEL : T40-315 Working Frequency: 315MHz for APPLICANT: Portman Security System International Co., Ltd. ADDRESS: 9F-2, No. 8, Lane 609, Chung Hsin Rd., Sec. 5, San Chung City, Taipei County, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 8, LANE 29, WEN-MING RD., LO-SHAN TSUN, KUI-SHAN HSIANG, TAOYUAN HSIEN 333, TAIWAN, R.O.C. Tel: (03) 3276170-3276174 Fax: (03) 3276188 Report Number: ET91S-12-105-05 ETC Report No.: ET91S-12-105-05FCC ID: OBDT-39-40-41-315 Rev. No 1.0 TEST REPORT CERTIFICATION Applicant: Portman Security System Internatinal Co., Ltd. 9F-2, No. 8, Lane 609, Chung-Hsin Rd., Sec. 5, San Chung City, Taipei County, Taiwan Manufacturer: Portman Electronics [Shenzhen] Ltd. The Ninth Building, Tong-Fuyu Industrial District, Long Hua Town, Bao’an Shenzhen, China Description of EUT: a) Type of EUT: Car Alarm Transmitter b) Trade Name: ---- c) Model No.: T40-315 d) FCC ID: OBDT-39-40-41-315 e) Working Frequency: 315MHz f) Power Supply: DC 12V Battery(TYPE:27A) Regulation Applied: FCC Rules and Regulations Part 15 Subpart C (2002) I HEREBY CERTIFY THAT; The data shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The results of the testing report relate only to the items tested. 2. The testing report shall not be reproduced except in full, without the written approval of ETC. Test Date: Dec. 25, 2002 Test Engineer: Approve & Authorized Signer: Win-Po Tsai, Manager, NVLAP Signatory EMC Dept. I of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No.: ET91S-12-105-05FCC ID: OBDT-39-40-41-315 Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION............................................................................................................................................................1 1.1 PRODUCT DESCRIPTION...................................................................................................................................................................1 1.2 CHARACTERISTICS OF DEVICE:.......................................................................................................................................................1 1.3 TEST METHODOLOGY......................................................................................................................................................................1 1.4 TEST FACILITY..................................................................................................................................................................................1 2. DEFINITION AND LIMITS..............................................................................................................................................................2 2.1 DEFINITION........................................................................................................................................................................................2 2.2 RESTRICTED BANDS OF OPERATION.............................................................................................................................................2 2.3 LIMITATION.......................................................................................................................................................................................2 2.4 LABELING REQUIREMENT...............................................................................................................................................................4 2.5 USER INFORMATION.........................................................................................................................................................................4 3. RADIATED EMISSION MEASUREMENT....................................................................................................................................5 3.1 APPLICABLE STANDARD.................................................................................................................................................................5 3.2 MEASUREMENT PROCEDURE..........................................................................................................................................................5 3.3 DEVIATIONS STATEMENT OF TEST..............................................................................................................................................5 3.4 TEST DATA.........................................................................................................................................................................................7 3.5 FIELD STRENGTH CALCULATION................................................................................................................................................10 3.6 RADIATED TEST EQUIPMENT.......................................................................................................................................................11 3.7 MEASURING INSTRUMENT SETUP...............................................................................................................................................12 3.8 RADIATED MEASUREMENT PHOTOS...........................................................................................................................................13 4. BANDWIDTH OF EMISSION......................................................................................................................................................14 4.1 APPLICABLE STANDARD PLOT GRAPHIC OF BANDWIDTH....................................................................................................14 4.2 BANDWIDTH TEST EQUIPMENT....................................................…

Text truncated - open the document above for the full version.

ETC Report No.: ET91S-12-105-05Page 1 of 1 FCC ID: OBDT-39-40-41-315 3.8 Radiated Measurement Photos