OGU722022Clearview BLE/IR Badge

MIDMARK RTLS FCC User Guide For BLE TRACKING Version 1.7 6/14/2022 FCC User Guide Page 2 Rev. 1.0 6/14/2022 © 2020 Midmark RTLS Solutions, Inc., Traverse City, Michigan USA © 2020 Midmark RTLS Solutions, Inc., Traverse City, Michigan USA This document contains user information on technology that is proprietary to Midmark RTLS Solutions, Inc. Permitted transmittal, receipt or possession of this document does not express license or imply any rights to use, sell, design or manufacture this information. No reproduction, publication or disclosure of this information, in part or in whole, shall be made without prior written authorization of Midmark RTLS Solutions, Inc. WARNING! This product is not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury, death or severe property damage. All patient, staff and asset names in this document are fictional. Because Midmark RTLS Solutions, Inc. is continually improving its products, specifications within all Midmark RTLS manuals are subject to change without notice. Midmark RTLS Solutions Inc. is an ISO 9001 Certified Company. Midmark RTLS products and solutions are provided by Midmark RTLS Solutions, Inc. f/k/a Versus Technology, Inc., a wholly owned subsidiary of Midmark Corporation. For more information, contact 1.800.MIDMARK, or call Midmark RTLS directly at 1.877.983.7787. Visit our website at midmarkRTLS.com. Revision Date: October 2020 Proprietary Information FCC User Guide Page 3 Rev. 1.0 6/14/2022 © 2020 Midmark RTLS Solutions, Inc., Traverse City, Michigan USA FCC STATEMENT: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 3. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator (VER5800 Plug in Sensor) & your body. The device shall be used in such a manner that the potential for human contact normal operation is minimized. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Components comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) These devices may not cause harmful interference, and 2) These devices must accept any interference received, including interference that may cause undesired operation. FCC User Guide Page 4 Rev. 1.0 6/14/2022 © 2020 Midmark RTLS Solutions, Inc., Traverse City, Michigan USA 5. CANADA STATEMENT: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement CAN ICES-3 (B)/NMB-3(B) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation. 6. Canada RF Exposure Statement: The device shall be used in such a manner that the potential for human contact normal operation is minimized. This equipment complies with RSS-102 radiation exposure limits. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Le dispositif doit être utilisé de manière à réduire au minimum le risque de fonctionnement normal en contact humain. Cet équipement est conforme aux limites d’exposition au rayonnement RSS-102. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet appareil et ses antennes ne doivent pas être situés conjointement ou fonctionner conjointement avec une autre…

Text truncated - open the document above for the full version.

Antenna Description The antenna is a ¼ wave monopole PCB antenna approximately 2.5 cm long with 0 dBi gain transmitting over the low, mid and high channels of 2.402, 2.440, and 2.480 GHz, respectively.

Engineering Test Report No. 2201228-02 Report Date April 8, 2022 Manufacturer Name Fleetwood Group Inc Manufacturer Address 11832 James Street Holland, MI 49424 Product Name Brand/Model No. VER5854 Date Received April 6, 2022 Assessment Dates April 6, 2022 – April 7, 2022 Specifications FCC 47 CFR Part 2.1093 KDB, 447498 D01 OET Bulletin 65:1997 RSS-102 EN 62311 EN 62479 AS/NZS 2772.2 RSP 3 Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 Signature Tested by Nathaniel Bouchie Signature Approved by Raymond J. Klouda, Registered Professional Engineer of Illinois – 44894 PO Number R63037 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Engineering Test Report No. 2201228-02 This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Page 2 of 16 Table of Contents 1. Report Revision History ............................................................................................................................ 3 2. Introduction ............................................................................................................................................... 4 3. Subject of Investigation ............................................................................................................................. 4 4. Standards and Requirements ................................................................................................................... 4 5. Sample Calculations ................................................................................................................................. 5 6. Photographs of EUT .................................................................................................................................. 6 7. Limits and Requirements .......................................................................................................................... 8 7.1. Requirements mandated by the FCC ....................................................................................................... 8 7.2. Requirements mandated by Innovation, Science and Economic Development Canada ......................... 9 7.3. Requirements mandated by the European Union and outlined in EN 62311 ......................................... 10 7.4. Requirements mandated by Australia/New Zealand and outlined in AS/NZS 2772.2 ............................ 11 8. Assessment Results ................................................................................................................................ 12 8.1. RF Exposure Evaluation Relevant to the Requirements of the FCC ...................................................... 12 8.2. RF Exposure Evaluation Relevant to the Requirements of ISED ........................................................... 13 8.1. RF Exposure Evaluation Relevant to the Requirements of the EU ........................................................ 14 8.1. RF Exposure Evaluation Relevant to the Requirements of Australia/New Zealand ............................... 15 9. Statement of Compliance ........................................................................................................................ 16 Engineering Test Report No. 2201228-02 Page 3 of 16 1. Report Revision History Revision Date Description – 14 APR 2022 Initial Release of Engineering Test Report No. ETR 2201228-02 Engineering Test Report No. 2201228-02 Page 4 of 16 2. Introduction The FCC, Innovation, Science and Economic Development Canada, European Union and Australia/New Zealand publish standards regarding the evaluation of the RF Exposure hazard of radio communications devices. An evaluation has been performed on the Fleetwood Group Inc BLE Clearview Badge, Model No. VER5854 pursuant to the relevant requirements. 3. Subject of Investigation This document presents the demonstration of RF Exposure compliance on a BLE Clearview Badge, (hereinafter referred to as the Equipment under Test (EUT)). The EUT was identified as follows: EUT Identification Description BLE Clearview Badge Model/Part No. VER5854 S/N Unit 1 Radio Access Technology Bluetooth Low Energy Equipment Class Portable Minimum Separation Distance 0.5cm Conducted Output Power 1.4dBm EIRP 4.4dBm Bands of Operation 2.4 GHz Bluetooth Antenna Gain 0 4. Standards and Requirements The tests were performed to selected portions of, and in accordance with the following specifications. - 47 CFR Parts 1.1310, 2.1091 and 2.1093 Code of Federal Regulations, Title 47, Telecommunications - KDB 447498 D01 – “RF Exposure Procedures and Equipment Authorization Polices for Mobile and Portable Devices, General RF Exposure Guidance v06” - OET Bulletin 65 Edition 97-01:1997 – “Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields” - A…

Text truncated - open the document above for the full version.

Engineering Test Report No. 2201228-01 Report Date March 7, 2022 Manufacturer Name Fleetwood Group Inc. Manufacturer Address 11832 James Street Holland, MI 49424 Product Name Model No. BLE Clearview Badge VER5854 Date Received March 6, 2022 Test Dates March 6, 2022 – March 7, 2022 Specifications FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C, Section 15.247 Innovation, Science, and Economic Development Canada, RSS-GEN Innovation, Science, and Economic Development Canada, RSS-247 Test Facility Elite Electronic Engineering, Inc. 1516 Centre Circle, Downers Grove, IL 60515 FCC Reg. Number: 269750 IC Reg. Number: 2987A CAB Identifier: US0107 Signature Tested by Nathaniel Bouchie Signature Approved by Raymond J. Klouda, Registered Professional Engineer of Illinois – 44894 PO Number P63037 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Elite Electronic Engineering Incorporated certifies that the information contained in this report was obtained under conditions which meet or exceed those specified in the FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C, Section 15.247 and Innovation, Science, and Economic Development Canada, RSS-247 test specifications. The data presented in this test report pertains to the EUT on the test dates specified. Any electrical or mechanical modifications made to the EUT subsequent to the specified test date will serve to invalidate the data and void this certification. This report must not be used to claim product certification, approval, or endorsement by A2LA, NIST, or any agency of the Federal Government. Engineering Test Report No. 2201228-01 This report shall not be reproduced, except in full, without the written approval of Elite Electronic Engineering Inc. Page 2 of 54 Table of Contents 1. Report Revision History ............................................................................................................................ 3 2. Introduction ............................................................................................................................................... 4 2.1. Scope of Tests .......................................................................................................................................... 4 2.2. Purpose ..................................................................................................................................................... 4 2.3. Identification of the EUT ............................................................................................................................ 4 3. Power Input ............................................................................................................................................... 4 4. Grounding ................................................................................................................................................. 4 5. Support Equipment ................................................................................................................................... 4 6. Interconnect Leads .................................................................................................................................... 5 7. Modifications Made to the EUT ................................................................................................................. 5 8. Modes of Operation ................................................................................................................................... 5 9. Test Specifications .................................................................................................................................... 5 10. Test Plan ................................................................................................................................................... 5 11. Deviation, Additions to, or Exclusions from Test Specifications ............................................................... 5 12. Laboratory Conditions ............................................................................................................................... 6 13. Summary ................................................................................................................................................... 6 14. Sample Calculations ................................................................................................................................. 6 15. Statement of Conformity ........................................................................................................................... 7 16. Certification ............................................................................................................................................... 7 17. Photographs of EUT .......................................…

Text truncated - open the document above for the full version.

Test Setup for Spurious Radiated Emissions, 30MHz – 1GHz – Antenna Polarization Horizontal Test Setup for Spurious Radiated Emissions, 30MHz – 1GHz – Antenna Polarization Vertical Test Setup for Spurious Radiated Emissions, 1 – 18GHz – Antenna Polarization Horizontal Test Setup for Spurious Radiated Emissions, 1 – 18GHz – Antenna Polarization Vertical Test Setup for Spurious Radiated Emissions, Above 18GHz – Antenna Polarization Horizontal Test Setup for Spurious Radiated Emissions, Above 18GHz – Antenna Polarization Vertical