OJFE62-N3-7USRemote Unit, Radio Node

Corning Optical Communications E62-A3-E3-N3 Specification Sheet | 28 March 28, 2022 | Page 1 Everon 6200 A3-E3-N3 Specification Sheet Corning Optical Communications E62-A3-E3-N3 Specification Sheet | 28 March 28, 2022 | Page 2 Features 1200MHz Transmission Bandwidth over 1 fiber 8 x 3GPP Band per Remote Sub 6GHz Up to 200MHz IBW Dry contact Alarm 25dBm Maximum Output Power per Band Support Band or Channel Selective filter Cascading up to 6 levels E62-A3 - Access Unit Chassis The E62-A3 – Access Unit Chassis is a standard 19-inch 2U rack-mounted shelf (1U fan unit included), which serves as the host for Everon™ 6200. The E62-A3 provides coupling access to radio signal sources of multi- operator, multi-system, and multi-band, forming digital optical signals and distributing static capacity distribution to fiber-connected other type devices. One A3 supports up to eight optical interfaces connected to E3s (Expansion Unit) or N3RUs (Remote Unit). This document describes the installation procedure for the E62-N3 remote unit. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. NOTE: Only authorized person can enter the area where the antenna is installed. And the person is fully aware of the potential for exposure and can exercise control over his or her exposure by leaving the area or by some other appropriate means. Awareness of the potential for RF exposure in a workplace or similar environment can be provided through specific training as part of a RF safety program. This device must be professionally installed. Corning Optical Communications E62-A3-E3-N3 Specification Sheet | 28 March 28, 2022 | Page 3 E62-AU-AC – Active Combiner Module The E62-AU-AC – Active Combiner Module is the interface to the operator base station signal source equipment. Each module has four QMA ports for signal input from the maximum four operators. One Access Unit can be equipped with up to four modules. In accordance with wireless service provider standards, it is not advised to use digital repeaters as a signal source for Corning solutions. E62-E3-O - Expansion Unit The E62-E3-O – Expansion Unit is a standard 19-inch 1U rack-mounted shelf, which serves as the interface between the Primary A3 and the Remote Unit for the capacity expansion of system. E62-N3RU – Low Power Remote Unit Corning Optical Communications E62-A3-E3-N3 Specification Sheet | 28 March 28, 2022 | Page 4 The E62-N3RU is a low-power remote unit supporting cellular technologies on fiber optic cable using the CPRI protocol. The N3 is ideal for multi-operator multi-band, static capacity distribution deployments of cellular services in small-to-medium coverage areas. The N3 supports up to four 25 dBm RF channels. The N3 converts an optical signal to RF and then transmits at the relevant 3GPP band and receives the analog RF signal, conditions it, and converts it back to optical for routing to the E3 or A3. The socket-outlet shall be easily accessible. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Specifications E62-A3 - Access Unit Chassis Supported Bands Band 3GPP Band Downlink Uplink Max IBW 600MHz 71 617-652 663-698 35 700 LU 12 & 13 729-756 699-716 & 777-787 27 700MHz LUPS 12 & 13 & 14 728-768 698-716 & 776-798 40 850E MHz 26 859-894 814-849 35 1900MHz 25 1930-1995 1850-1915 65 2100MHz 66E 2110-2200 1710-1780 90 2300MHz 30 2350-2360 2305-2315 10 2500MHz TDD 41 2496-2690 2496-2690 194 C-Band-1 n78 3450-3800 3450-3800 200 Corning Optical Communications E62-A3-E3-N3 Specification Sheet | 28 March 28, 2022 | Page 5 C-Band-2 n77 3700-3980 3700-3980 200 Interface Access Unit RF Interface QMA Female Optical Connector Type 8 x 25 GBps SFP+ Interfaces 6 to 8 optical connections to E3-O or N3 2 optical connections to Secondary A3s Transmission Rate 25 GB/s AU-AC modules 4 x AU-AC modules per chassis (RF interface with BTS) Full 3GPP Band per Module (up to 200 MHz) Band Support 12x 3GPP bands over 1 fiber core (using 2 x Secondary A3) Dry contact Alarms 1x RJ45 (2x in, 2x out) Maintenance Interface Ethernet RJ45 AU-AC power level (dB) 0dBm to +15 dBm Input Power Range for each port Electrical Electromagnetic Compatibility/Interference (EMC/EMI) 3GPP TS38.113 Maximum Power Consumption 85W AC Power 100-240v AC, 50/60Hz DC Power 48VDC ± 20% Environmental Mean Time Between Failure (MTBF) > 220,000 hours Operating Temperature -10°C to +45°C Storage Temperature -40°C to +85°C Humidity 0% to 90% (Noncondensing) Cooling Active Installation Wall or 19-in Rack Ingress Protection Rating IP30 (Indoor) Mechanical AU (Width / Height / Depth / Weight) 440mm / 88mm / 329mm / 8.0kg 17.32in / 3.46in / 12.95in / 17.64lb E62-E3-O - Expansion Unit Interface Optical Connector Type 16 x 25 GBps SFP+ Interfaces 14x optical connections to N3RU 1x optical connection to Primary A3 or upper level E3 1x optical connection to lower level E3 Transmission Rate 25 GB/s Cascading Up to 5 x E3-O per Optical connection Dry contact Alarms 1x RJ45 (2x in, 2x out) Maintenance Interface Ethernet RJ45 Electrical Electromagnetic Compatibility/Interference (EMC/EMI) 3GPP TS38.113 Maximum Power Consumption 65 W AC Power 100-240 VAC, 50/60 Hz DC Power 48VDC ± 20% Environmental Corning Optical Communications E62-A3-E3-N3 Specification Sheet | 28 March 28, 2022 …

Text truncated - open the document above for the full version.

Corning Restricted Corning Optical Communications LLC To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Corning Optical Communications LLC 840 N McCarthy Blvd, Milpitas, California, United States, 95035 For FCC ID: OJFE62-N3-7US; Model number: E62-N3 According to: FCC KDB 935210 D02 Signal Boosters Certification v04r02 For PART 90 booster device, Section V (g) requirement: (g)Attestation (must be non-confidential exhibit, signed by the applicant; signature by test lab, agent, or TCB is not acceptable) should include: (1)Warning label messages and Class B disclosure will be also shown in online and point-of-sale marketing materials and on outside packaging of device: For PART 20 booster device, IV.(d) requirement: (d)) Attestation (must be non-confidential exhibit, signed by the applicant; signature by test lab, agent, or TCB is not acceptable) should include: (1) Warning label messages will be also shown in online and point-of-sale marketing materials and on outside packaging of device We Corning Optical Communications LLC declared our Warning label messages and Class B disclosure will be also shown in online and point-of-sale marketing materials and on outside packaging of device. WARNING: This is a part 20 and part 90 class B signal booster device. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. You MUST register Class B signal boosters (as defined in 47 CFR 90.219) online at www.fcc.gov/signal-boosters/registration. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. Sincerely, Name (Printed): Dana Whitney Title: Director of Operations and Program Signature: On behalf of Company: Corning Optical Communications LLC Corning Restricted © 2020 Corning Incorporated. All Rights Reserved.

Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 2 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States General - Corning (L4) Applicant Legal Business Name Corning Optical Communications LLC Address 840 N McCarthy Blvd, Milpitas, California, United States, 95035 Grantee Code OJF FCC ID OJFE62-N3-7US Authorized Contact Name Dana Whitney Contact Email [email protected] Contact Phone +(1) 833-426-7646 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1)labeling the equipment with the exact FCC ID as specified in this application, (2)compliance statement labeling pursuant to the applicable rules, (3)compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1)the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2)the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3)the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List [Corning Optical Communication LLC (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Corning Optical Communication LLC (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date:2024/07/18 Print Name: Dana Whitney Title: Director of Operations and Program *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 2 of 2 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States General - Corning (L4)

General - Corning (L4) UNITED STATES DESIGNATED AGENT LETTER Date: 2024/07/18 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant U.S. designated agent Company Name: Corning Optical Communications LLC Company Name: Corning Optical Communications LLC Grantee Code: OJF Contact Name: Dana Whitney Contact Name: Dana Whitney Address: 840 N McCarthy Blvd, Milpitas, California, United States, 95035 Address: 840 N McCarthy Blvd, Milpitas, California, United States, 95035 City/Province/Zip: Milpitas/ California/ 95035 City/Province/Zip: Milpitas/ California/ 95035 Telephone: 817-431-7894 Telephone: 817-431-7894 Fax: 817-431-7894 Fax: 817-431-7894 Email: [email protected] Email: [email protected] FRN: 0017154329 Applicable Equipment: FCC ID: OJFE62-N3-7US ATTN: Director of Certification: We, < Corning Optical Communications LLC > and < Corning Optical Communications LLC > understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < Corning Optical Communications LLC > and < Corning Optical Communications LLC > acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Dana Whitney Name (Printed): Dana Whitney Title: Director of Operations and Program Title: Director of Operations and Program

Corning Optical Communications LLC Current Date 2024-07-18 To: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products *WE Corning Optical Communications LLC HEREBY DECLARED THAT Product Description: Remote Unit, Radio Node Model No.: SCRN-620 Manufacturer’s Name: Corning Optical Communications LLC Manufacturer’s Address: 840 N McCarthy Blvd, Milpitas, California, United States *Except that the model number and appearance deviation, are identical with the original product as follows: Note: The definition of identical should be “electrically identical”. A device will be considered to be electrically identical if no changes are made to the devices’ schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical with the model which has been tested by SGS. Model No.: E62-N3 Manufacturer’s Name: Corning Optical Communications LLC Manufacturer’s Address: 840 N McCarthy Blvd, Milpitas, California, United States Sincerely, Signature: Printed Name : Dana Whitney Position/Title : Director of Operations and Program Contact Number: +(1) 833-426-7646

Corning Optical Communications LLC Date: 2024-07-18 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: OJFE62-N3-7US To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Corning Optical Communications LLC. This authorization is valid until further written notice from the applicant. Name (Printed): Dana Whitney Title: Director of Operations and Program Signature/Electronic Signature: On behalf of Company: Corning Optical Communications LLC Telephone: +(1) 833-426-7646

General - Corning (L4) Corning Optical Communications LLC To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Corning Optical Communications LLC 840 N McCarthy Blvd, Milpitas, California, United States Regarding: Confidentiality Request regarding application for FCC ID: OJFE62-N3-7US LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. •Block Diagram •Operational Description •Schematics •Tune-up •BOM The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature/Electronic Signature: Printed Name (on file with the FCC associated with the Grantee Code): Dana Whitney Title: Director of Operations and Program Company Name: Corning Optical Communications LLC

Compliance Certification Services (Kunshan) Inc. Page: 1 of 4 Appendix Photographs of External photo for KSCR2406001179AT Test Model No.: E62-N3 Compliance Certification Services (Kunshan) Inc. Page: 2 of 4 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 4 Compliance Certification Services (Kunshan) Inc. Page: 4 of 4

Input: 48V 2A Made in China 12-2023 P/N: SCRN-620-7777667US REV: 001 S/N: 362348XXXXXMAC: XXXXXXXXXXXXX Made in China 12-2023 P/N: SCRN-620-7777667US S/N: 362348XXXX REV: 001 MAC: XXXXXXXXXXXX Input: 48V 2A CLASS 1 LASER PRODUCT CLASS 1 LASER PRODUCT 包装上不贴 包装上不贴 包装上不贴 FCC ID ： OJFE62-N3-7US 1 2 3 4 5 678 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. REL: V2.13 REL: V2.13 7US 7US FCC ID ： OJFE62-N3-7US This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1 2 3 4 5 6 7 8 7US 7US Made in China 12-2023 P/N: SCRN-620-7777667US S/N: 362348XXXX REV: 001 MAC: XXXXXXXXXXXX Input: 48V 2A CLASS 1 LASER PRODUCT REL: V2.13 WARNING! This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS . You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. You MUST register Part 90 Class Band Part 20 signal Boosters (as defined in 47 CFR 90.219)online at www.fcc.gov/signal-boosters /registration. Unauthorized use may result in significant forfeiturepenalties, including penalties in excess of $100,000 for each continuing violation. Part90 and Part 20 Signal Booster THIS IS A 90.219 CLASS B DEVICE WARNING! This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS . You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. You MUST register Part 90 Class B and Part 20 signal Boosters (as defined in 47 CFR 90.219) online at www.fcc.gov/signal-boosters /registration. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. Part90 and Part 20 Signal Booster THIS IS A 90.219 CLASS B DEVICE Remote Unit, E62-N3 Everon 6200 TM Everon 6200 TM Remote Unit, E62-N3 Everon 6200 TM Remote Unit, E62-N3

Input: 48V 2A Made in China 12-2023 P/N: SCRN-620-7777667US REV: 001 Radio Node, SCRN-620 S/N: 362348XXXXXMAC: XXXXXXXXXXXXX Made in China 12-2023 P/N: SCRN-620-7777667US S/N: 362348XXXX REV: 001 MAC: XXXXXXXXXXXX Input: 48V 2A CLASS 1 LASER PRODUCT CLASS 1 LASER PRODUCT 包装上不贴 包装上不贴 包装上不贴 FCC ID ： OJFE62-N3-7US 1 2 3 4 5 678 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Node, SCRN-620 REL: V2.13 REL: V2.13 7US 7US FCC ID ： OJFE62-N3-7US This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1 2 3 4 5 6 7 8 7US 7US Made in China 12-2023 P/N: SCRN-620-7777667US S/N: 362348XXXX REV: 001 MAC: XXXXXXXXXXXX Input: 48V 2A CLASS 1 LASER PRODUCT Radio Node, SCRN-620 REL: V2.13 WARNING! This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS . You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. You MUST register Part 90 Class Band Part 20 signal Boosters (as defined in 47 CFR 90.219)online at www.fcc.gov/signal-boosters /registration. Unauthorized use may result in significant forfeiturepenalties, including penalties in excess of $100,000 for each continuing violation. Part90 and Part 20 Signal Booster THIS IS A 90.219 CLASS B DEVICE WARNING! This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS . You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. You MUST register Part 90 Class B and Part 20 signal Boosters (as defined in 47 CFR 90.219) online at www.fcc.gov/signal-boosters /registration. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. Part90 and Part 20 Signal Booster THIS IS A 90.219 CLASS B DEVICE

Compliance Certification Services (Kunshan) Inc. Page: 1 of 4 Appendix Photographs of Internal photo for KSCR2406001179AT Test Model No.: E62-N3 Compliance Certification Services (Kunshan) Inc. Page: 2 of 4 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 4 Compliance Certification Services (Kunshan) Inc. Page: 4 of 4

Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600117905 Page: 1 of 7 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Member of the SGS Group (SGS SA) 1 Cover Page RF MPE REPORT Application No.: KSCR2406001179AT FCC ID: OJFE62-N3-7US Applicant: Corning Optical Communications LLC Address of Applicant: 840 N McCarthy Blvd, Milpitas, California, United States Manufacturer: Corning Optical Communications LLC Address of Manufacturer: 840 N McCarthy Blvd, Milpitas, California, United States Equipment Under Test (EUT): EUT Name: Remote Unit, Radio Node Model No.: E62-N3, SCRN-620 Trade mark: Standard(s) : FCC Rules 47 CFR §2.1091 KDB447498 D01 General RF Exposure Guidance v06 Date of Receipt: 2024-06-26 Date of Test: 2024-06-26 to 2024-08-26 Date of Issue: 2024-08-26 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600117905 Page: 2 of 7 Revision Record Version Description Date Remark 00 Original 2024-08-26 / Authorized for issue by: Tested By Damon Zhou /Project Engineer Approved By Terry Hou /Reviewer Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600117905 Page: 3 of 7 2 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Contents .................................................................................................................................................... 3 3 General Information .................................................................................................................................. 4 3.1 General Description of E.U.T. ............................................................................................................ 4 3.2 Technical Specifications ..................................................................................................................... 4 3.3 Test Location ...................................................................................................................................... 5 3.4 Test Facility ........................................................................................................................................ 5 4 Test Standards and Limits ....................................................................................................................... 6 4.1 FCC Radiofrequency radiation exposure limits: ................................................................................. 6 5 Measurement and Calculation ................................................................................................................. 7 5.1 Maximum transmit power ................................................................................................................... 7 Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600117905 Page: 4 of 7 3 General Information 3.1 General Description of E.U.T. Power Supply: AC :100-240V~ 3A 50/60Hz DC: -48VDC 6.5A 3.2 Technical Specifications Frequency Band: Booster: 746MHz-756MHz, 758MHz-768MHz Base station:746MHz-756MHz, 758MHz-768MHz Antenna Type: Internal Antenna Gain: 3dBi (Provided by manufacturer) Modulation Type: Booster: 5G NR: CP-OFDM: QPSK, 16QAM, 64QAM, 256QAM LTE: QPSK, 16QAM, 64QAM, 256QAM Base station: 5G NR: CP-OFDM: QPSK, 16QAM, 64QAM, 256QAM Antenna Delivery: MIMO 2*2, SISO Temperature Range: -10°C to 45°C Note: The antenna gain value is provided by the customer. The test lab will not be responsible for wrong test result due to incorrect information about antenna gain values. Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600117905 Page: 5 of 7 3.3 Test Location All tests were performed at: Compliance Certification Services (Kunshan) Inc. No.10 Weiye Rd, Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China. Tel: +86 512 5735 5888 Fax: +86 512 5737 0818 No tests were sub-contracted. Note: 1.SGS is not responsible for wrong test results due to incorrect information (e.g., max. internal working frequency, antenna gain, cable loss, etc) is provided by the applicant. (If applicable). 2.SGS is not responsible for the authenticity, integrity and the validity of the conclusion based on results of the data provided by applicant. (If applicable). 3. Sample source: sent by customer. 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA Compliance Certifi…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600117903 Page: 1 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsifi…

Text truncated - open the document above for the full version.