OKP0850Rovio Pivot

USER MANUAL ITEM NO.: 0850THE ULTIMATE TABLET STAND 1 Thank you for purchasing Rovio Pivot™ from WowWee™! Rovio Pivot™ is a multi-functional tablet stand that serves a variety of consumer needs including remote video conferencing, as well as a built-in entertainment system. Package contents Please note the following when operating Rovio Pivot™: • Do not immerse Rovio Pivot™ or any parts in water or any other form of liquid. • Do not drop, throw, or kick Rovio Pivot™ as this might damage mechanical functions. • Do not manually turn Rovio Pivot™ in either direction while it is moving. 1 x Rovio Pivot™ USEUUK 2 x Grip Adapters INTRODUCTION • 1 x Instruction Sheet 1 x 5V AC/DC Power Adapter 1 x Remote Controller Interchangeable Plugs* * Number of plugs may vary depending on region. 2.1 2.2 2 BATTERY INFORMATION Installing or changing batteries in the Remote Controller: 1. To change the batteries, turn to the back of the Remote Controller. The Remote Controller requires 1 x “CR2032 3V” size battery (included). 2. Remove the Battery Holder by pressing the latch located on the left, towards the right and pull downwards as shown in diagram. 3. Insert the battery according to the diagram. Ensure that the positive and negative polarities match the illustration shown. 4. Push the Battery Holder all the way back into the Remote Controller. A soft click indicates that the Battery Holder has been securely attached. NOTE: Out of the box, you will notice a clear plastic strip extending from within the battery compartment of the Remote Controller. Activate the Remote Controller by removing and discarding this insulation tab by pulling in the direction shown. The Remote Controller functions without this tab. Installing or changing the Interchangeable Plugs: 1. To change the Interchangeable Plugs, first press and hold on the Lock Release Button. 2. Then twist plug as shown in diagram to release. 3. Position desired plug in position and twist in the opposite direction to lock. A soft click indicates that the plug has been securely attached. TIP: Positioning steel pins to the top of the adapter will facilitate assembly. NOTE: Rovio Pivot™ must only be used with the transformer included. IMPoRtant BatteRY InFoRMatIon: • Use only fresh batteries of the required size and recommended type. • Please respect the correct polarity, (+) and (-). • Do not try to recharge non-rechargeable batteries. • Do not throw batteries into fire. • The supply terminals are not to be short-circuited. • Remove exhausted batteries from the unit. • Batteries should be replaced by adults. Press Lock Release Button T W I S T O p e n L o c k CR2032 3V 3 Adjustable Clamps Adjustable Rotation Joint Stand Head Swivel Joint Adjustable Tilt Joint Smart Device Cable Neck Speakers Power Button Device Rest IR Sensor Status Indicator (RGB LED) Stand Head Device Support Pads Device Support Pads Cable Access Touch-Sensitive Control Panel QUICK OVERVIEW MOTORIZED BASE ROVIO PIVOT™ CENTER POSITIVE 9V 1A 4 Right Turn Battery Holder IR Transmitter Home Position Power Adapter Port Left Turn USB Charging Port Power Button Mute Button Call Answer/End Button Control Panel Buttons (Functions as above) QUICK OVERVIEW MOTORIZED BASE - REAR TOUCH-SENSITIVE CONTROL PANEL REMOTE CONTROLLER Remote Controller (Front View) Remote Controller (Rear View) DV IN 9V 1A 5 Rovio Pivot™ acts as a stand for your tablet smart device, with a tilt neck and three-position 90° swivel clamp. Rovio Pivot™ can also turn left and right or return to the Home position, either using the Touch-Sensitive Control Panel on the base or with the Remote Controller. Other features include outputting sound through Rovio Pivot™ and charging your tablet smart device. Setting Up The Rovio Pivot™ Unit 1. Place Rovio Pivot™ on a flat surface, making sure the feet are all evenly touching the surface. 2. Plug the AC / DC Adapter into the Power Adapter Port on the Rovio Pivot™ unit, then plug the AC / DC Adapter into a wall socket. 3. Push the “Power Button” to turn Rovio Pivot™ on. Connecting A Tablet Smart Device To connect Pivot to a smart device: 1. Gently slot your smart device into the Stand Head and push the Left and Right Adjustable Clamps together until the device is held securely*. NOTE: Be sure to place the base of your smart device on the Device Rest. * If you are experiencing difficulty in securing your device, insert the Grip Adapters then reclamp for a tighter fit. GETTING STARTED Inserting your device Securing your deviceInserting Grip Adapters Connecting the Power Adapter 6 2. To ensure that sound is played back through Rovio Pivot™, insert the Smart Device Cable into the headphone jack on the smart device. NOTE: To control the volume level, please use the buttons on your smart device. 3. To charge your device via Rovio Pivot™, first check that the unit is connected to a power source using the included Power Adapter. Then, connect your USB charge cable (not included) to the USB Charging Port located on the back of the base. Insert the other end of the charge cable into your smart device and it will commence charging. NOTE: With the Power Adapter connected, Rovio Pivot™ is capable of charging your smart device even when the unit is not switched on. GETTING STARTED Connecting the Smart Device Cable Connecting the USB Charging Port Connecting to your Device 7 Controlling Rovio Pivot™ To turn attached smart device to the left, press the “Left Turn Button” on the Touch-Sensitive Control Panel on the unit base or on the Remote Controller. To turn attached smart device to the right, press the “Right Turn Button” on the Touch-Sensitive Control Panel on the unit base or on the Remote Controller. To return to the Home position, press on the “Home Position Button” on the Touch-Sensitive Control Panel on the unit base or on the Remote Controller. Adjusting Rovio Pivot™ The viewing angle and position on Rovio Pivot™ can be adjusted manually for optimal viewing. Adjusting Tilt – While firmly holding…

Text truncated - open the document above for the full version.

Authority to Act as Agent Date: Sept 25, 2014 To Whom It May Concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Vicky Yuan in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: Sept 25, 2015 By: Dennis Tsoi (Signature) (Print name) Title: Quality Assurance Manager On behalf of: WowWee Group Limited (Company Name) Telephone: 852-2739-5288

Request for Confidentiality Date: Sept 25, 2014 Subject: Confidentiality Request for: FCC ID: OKP0850 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ WowWee Group Limited has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: Dennis Tsoi (Signature/Title 3 ) (Print name)

Statement Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: OKP0850 To Whom It May Concern: I, the undersigned, hereby attest to the fact that I will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1. Devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. 3. Pt 2.1077 contains the list of information that must be included in the Declaration of Conformity, which must be supplied with each product sold. The DoC compliance Info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(c)(2), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, By: Dennis Tsoi (Signature) (Print name) Title: Quality Assurance Manager On behalf of: WowWee Group Limited (Company Name)

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Member of the SGS Group (SGS SA) SGS IECC Limited Units 303-305, 3/F., 31 Lok Yip Road, On Lok Tsuen, Fanling, N.T., Hong Kong Telephone: +852 23052570 Fax: +852 27564480 FEDERAL COMMUNICATIONS COMMISSION CAB Registration number: 446297 No. VFHKEM1410001427RF Verification of Conformity for FCC DoC Procedure It is herewith confirmed and found the following designated product Product Name: Rovio Pivot Model: 0850 ( Product Identification ) to comply with the technical requirements set up by ANSI C63.4 & CFR 47 FCC PART 15 regulations for the evaluation of electromagnetic compatibility with. Test Report Number(s): HKEM141000142701 issued on: October 14, 2014 ( Identification of regulations / standards ) Applicant : WowWee Group Limited Address : 3/F, Energy Plaza, Suite 301 A-C, 92 Granville Road, T.S.T. East, Hong Kong. ( Applicant Identification ) TEST LABORATORY This is the test result, that was carried out based on the submitted sample(s) of the product in conformity with the specificatio n of the respective standards. CHEN Jian-feng, Jeffrey October 14, 2014 This verification is related to the submitted sample(s) and in conjunction with the test data detailed in the above test report.

1 Photographs - EUT Constructional Details

= Emboss [On Mold] = Black 7 C 10 October 2014 #0850 Rovio Pivot - Product Legal Lines + Printing • CANADIAN VERSION - IC Marking • Embossed items [MAGENTA in file] • Print items [as per KEY below] • Output Vectors to be extracted from THIS PDF file • Scale 1:1 NOTES: • Page 1 of 1 KEY: Stand BOTTOM VIEW FOR OUTPUT [PRINT] FCC ID: OKP0850 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WOWWEE GROUP LTD. Model No.: 0850 MADE IN CHINA ©2013 WOWWEE GROUP LTD 22.5mm 6mm

1 Photographs - EUT Constructional Details

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140900493902 Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page RF Exposure Evaluation Report Application No: SZEM1409004939RF Applicant: WowWee Group Limited Manufacturer: Wah Shing Toys Co., Ltd. Factory: Everwin Toys (Dongguan) Co. Ltd. Product Name: Rovio Pivot Model No.(EUT): 0850 Trade Mark: WowWee FCC ID: OKP0850 Standards: 47 CFR Part 1.1307(2013) 47 CFR Part 1.1310(2013) Date of Receipt: 2014-09-09 Date of Test: 2014-09-23 to 2014-10-09 Date of Issue: 2014-10-14 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140900493902 Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-10-14 Original Authorized for issue by: Tested By 2014-10-09 (Back Huang) /Project Engineer Date Prepared By 2014-10-14 (Sade Luo) /Clerk Date Checked By 2014-10-16 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140900493902 Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ....................................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140900493901 Page: 1 of 50 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1409004939RF Applicant: WowWee Group Limited Manufacturer: Wah Shing Toys Co., Ltd. Factory: Everwin Toys (Dongguan) Co. Ltd. Product Name: Rovio Pivot Model No.(EUT): 0850 Trade Mark: WowWee FCC ID: OKP0850 Standards: 47 CFR Part 15, Subpart C (2013) Date of Receipt: 2014-09-09 Date of Test: 2014-09-23 to 2014-10-09 Date of Issue: 2014-10-14 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140900493901 Page: 2 of 50 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-10-14 Original Authorized for issue by: Tested By 2014-10-09 (Back Huang) /Project Engineer Date Prepared By 2014-10-14 (Sade Luo) /Clerk Date Checked By 2014-10-16 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140900493901 Page: 3 of 50 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS AC Power Line Conducted Emission 47 CFR P…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: 0850 1.1 Conducted Emission 1.2 Radiated Emission