OKUSBB081FGBluetooth Speaker

Please read this instruction manual carefully and keep it for future reference. SOURCE TUN-TUN+AUX VOL-VOL+ Instruction Manual BLUETOOTH SPEAKER Model: SBB-081FG • CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. • WARNING: moisture. • CAUTION: may result in hazardous radiation exposure. • WARNING: for compliance could void the user’s authority to operate the equipment. WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging • WARNING: it may be the cause. • CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • WARNING: Shock hazard - Do Not Open. Mains plug is used as disconnect device and it should remain readily operable during intended use. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries. the surface. Use a protective barrier between the unit and surface to protect the surface. the remote. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the wall outlet completely. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION CAUTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may electric shock to persons. 1 • SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. This apparatus shall not be exposed to dripping or splashing, and no objects filled with liq uids, such as vases, shall be placed on the apparatus. 6. Clean on ly with a dry cloth. 7. Do not block any ventila tion openings. Install in accordance with the ma nufacturer’s instructions. The apparatus should not be situated on a bed, sofa, rug or similar surface that may block the ventilation openings. The apparatus must not be placed in a built-in installation, such as a closed bookcase or cabinet that may impede the flow of air through the ventilation openings. Ventilation should not be impeded by covering the openings with items such as newspapers, tablecloths , curtains, etc. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplif iers) that produce heat. Extended exposure to temperatures higher that 170 degrees Fahrenheit, for example inside a closed vehicle during the summer, may result in damage to your product. 9. No open flame sources, such as lighted candles, should be placed on the apparatus. 10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet. 11. Protect the pow er cord from being walked on or pinched – particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 12. Do not install in an area which impedes the access to the power plug. Disconnecting the power plug is the only way to completely remove power to the product and must be readily accessible at all times. 13. Power source – Use only power supplies of the type specif ied in the operating instructions or as marked on the appliance. If a separate power supply is included with this apparatus, do not substitute with any other power supply – use only manufacturer-provided power supplies. 14. Unplug this apparatus during lightning storms or when unused for long periods of time. 15. If the unit will be unused for long periods of time, the batteries should be removed. 16. Do not place this product on an unstable surface. The product may fall , causin g injury to a child or adult and damage to the product. Use only with a stand, bracket, or table recommended by use a mount ing accessory recommended by the manufacturer. 17. Move the appliance with care to avoid damage or injury. 18. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damages in any way: the power-supply cord or plug is damages, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 19. For products which incorporate batteries, please refer to local regulations for proper battery disposal. 2 Shock, do not expose t his product to rain or moisture. The product must not be exposed to dripping water and water placed on the product can be dangerous. Changes or modifications not app roved by the manufacturer could void the user’s authority to operate this device. Usage of controls or adjustments or herein may result in hazardous exposure. Refer all servici ng to quali fied service personnel. To reduce the risk of fire or electrical. No fire sources such as candles shou ld be placed near the unit and no object filled with liquids should be placed on the product. the manufacturer, or sold with the product. Any mounting of the product should follo w the manufacturer’s instructions, and should CALIFORNIA PROP 65 WARNING “WARNING”This prod uct contains chemicals known to the State of Calif ornia to cause birth defects or other reproductive harm. For more information on these regulations and a list of chemicals, log on the following website: http:// www.oehha.ca.gov/prop65.html Warning: Caution: CALIFORNIA PROP 65 WARNING 3 P…

Text truncated - open the document above for the full version.

Differences Declaration To whom concern, We Shenzhen Junlan Electronic Ltd hereby declares: The product model(s) SBB-081F, ITSB-201-37, ITSB-201-32, S BB-0116, SBB-0218, SBB-0718, SBB-02166, SBB-101F, SBB -101FA, SBB-101FB, SBB-101FC, SBB-181F4, SBB-0618, SBB-050A, SBB-031P, SBB-031PG, SBB-0319, SBB-040A, SBB-082FG, SBB-083FG, SBB-084FG, SBB-085FG, SBB-086FG, SBB-087FG, SBB-088FG, SBB-089FG, SBB-03004 are identical in the same PCB layout, interior structure and electrical circuits with the model SBB-081FG which tested in Global United Technology Services Co., Ltd., the only differences are the model name for commercial purpose. Authorized signature: Date: 2013-05-17

Shenzhen Junlan Electronic Ltd Date (dd/mm/yyyy) 05/17/2013 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, We, Shenzhen Junlan Electronic Ltd (address: District 2 type A plant in the second layer 1-4, NO.2 Industrial Fuyuan Tangwei Fuyong Baoan Shenzhen China), hereby authorize Hans.hu (Company name: Global United Technology Services Co., Ltd. Address: 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District Shenzhen Guangdong ) to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on 05/17/2014 Yours sincerely, Company Officer: safety engineer / Peng Xiao Telephone Number: 0755-27309169 Email: [email protected]

Shenzhen Junlan Electronic Ltd Date (dd/mm/yyyy) 05/17/2013 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Confidentiality Request FCC ID: OKUSBB081FG Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, Shenzhen Junlan Electronic Ltd hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Company Officer: safety engineer / Peng Xiao Telephone Number: 0755-27309169 Email: [email protected]

130500001 130500030 TO 流水号贴纸 尺寸：30*5mm 白底黑字 用量:1PC 贴机器后板 SERIAL NO LABEL SIZE:30*5MM PRINTED IN BLACK ON WHITE BACKGROUND QTY=1PC RATING LABEL SIZE:80*50MM PRINTED IN WHITE ON BLACK BACKGROUND QTY=1PC 铭牌贴纸 尺寸：80*50MM 黑底白字 用量:1PC 贴机器后板 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device might not cause harmful interference, and (2) this device must accept any interference received, including interference that might cause undesired operation. FCC LABEL SIZE:105*16MM PRINTED IN WHITE ON BLACK BACKGROUND QTY=1PC FCC 尺寸： *MM 黑底白字 用量:1PC 贴机器后板 贴纸 105 16 STEREO SOUNDBAR MODEL:SBB-081FG POWER SUPPLY: DC15V, 2A POWER CONSUMPTION: 25W FM FREQUENCY RANGE:87.5-108MHZ FCC ID: OKUSBB081FG MADE IN CHINA 2013 Innovative Technology 1 Channel Drive Port Washington, NY 11050 www.ithomeproducts.com c MODEL: SERIAL NO: SBB-081FG WARNING TO PREVENT ELECTRIC SHOCK DO NOT REMOVE BACK COVER NO USER SERVICEABLE PARTS INSIDE CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR AVERTISSEMENT

Label location

Global United Technology Services Co., Ltd. Global United Technology Services Co., Ltd.Project No.: GTSE130400563RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 1 FCC ID:OKUSBB081FG The device has a standalone transmission. According to KDB 447498 section 4.3.1, the 1-g SAR test exclusion thresholds at test separation distances≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHz)] ≤ 3.0 The maximum tune-up limit power is 0.13005mW@ 2.480GHz For the head and body SAR, use 5mm as the conservative minimum test separation distance, [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHz)] =0.041≤ 3.0 So standalone SAR measurements are not required for both head and body.

Global United Technology Services Co., Ltd. Report No.: GTSE13040056301 Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of GTS International Electrical Approvals or testing done by GTS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by GTS International Electrical Approvals in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” FCC REPORT Applicant: Shenzhen Junlan Electronic Ltd Address of Applicant: District 2 type A plant in the second layer 1-4, NO.2 Industrial Fuyuan Tangwei Fuyong Baoan Shenzhen China Equipment Under Test (EUT) Product Name: BLUETOOTH SPEAKER Model No.: SBB-081FG, SBB-081F, ITSB-201-37, ITSB-201-32, SBB-0116, SBB-0218, SBB-0718, SBB-02166, SBB-101F, SBB-101FA, SBB-101FB, SBB-101FC, SBB-181F4, SBB-0618, SBB-050A, SBB-031P, SBB-031PG, SBB-0319, SBB-040A, SBB-082FG, SBB-083FG, SBB-084FG, SBB-085FG, SBB-086FG, SBB-087FG, SBB-088FG, SBB-089FG, SBB-03004 Trade Mark: SCOTT FCC ID: OKUSBB081FG Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2012 Date of sample receipt: April 26, 2013 Date of Test: April 26-May 07, 2013 Date of report issued: May 07, 2013 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSE13040056301 Global United Technology Services Co., Ltd. Project No.: GTSE130400563RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 31 2 Version Version No. Date Description 00 May 07, 2013 Original Prepared By: Date: May 07, 2013 Project Engineer Check By: Date: May 07, 2013 Reviewer Report No.: GTSE13040056301 Global United Technology Services Co., Ltd. Project No.: GTSE130400563RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 31 3 Contents Page 1 COVER PAGE............................................................................................................................................ 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 CLIENT INFORMATION......................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.3 TEST MODE........................................................................................................................................ 7 5.4 DESCRIPTION OF SUPPORT UNITS....................................................................................................... 7 5.5 TEST FACILITY.................................................................................................................................... 7 5.6 TEST LOCATION................................................................................................................................. 7 5.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER......................................................................... 7 6 TEST INSTRUMENTS LIST ..................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA...................................................................................... 9 7.1 ANTENNA REQUIREMENT:.................................................................................................................... 9 7.2 CONDUCTED EMISSIONS................................................................................................................... 10 7.3 RADIATED EMISSION METHOD........................................................................................................... 13 7.3.1 Field Strength of The Fundamental Signal ................................................................................ 15 7.3.2 Spurious emissions.................................................................................................................... 16 7.3.3 Bandedge emissions.................................................................................................................. 20 7.4 20DB OCCUPY BANDWIDTH...............................................................................…

Text truncated - open the document above for the full version.

Radiated Emission Conducted Emission