OPPOBR3650HPVistaMAX OBR3650/HP+3.5 GHz Base Station Transceiver

Installation and Operation Guide VistaMAX OBR3650HP Outdoor Base Station Transceiver Proprietary to Vecima Networks Inc. (C) Vecima Networks Inc., 2009 Permission to Reproduce Except as otherwise specifically noted, the information in this publication may be reproduced, in part or in whole and by any means, without charge or further permission from Vecima Networks Inc., provided that due diligence is exercised in ensuring the accuracy of the information reproduced; that Vecima Networks Inc. is identified as the source; and that the reproduction is not represented as an official version of the information reproduced. This publication is also available electronically on the World Wide Web at the following address: www.vecima.com Vecima Networks Inc. reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Vecima Networks Inc. to provide notification of such revision or change. Vecima Networks Inc. provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Vecima Networks Inc. may make improvements or changes in the product(s) described in this manual at any time. Specifications subject to change without notice. Document: Approved: OBR3650HP_ml_r01_sd C.W. obr3650hp_ml_r01_sd Contents Contents........................................................................................................................................................................................................................................ 1-1 Preface.......................................................................................................................................................................................................................................... I-i Warnings and Advisories.......................................................................................................................................................................................... I-i Regulatory Notices........................................................................................................................................................................................................ I-ii Getting Support................................................................................................................................................................................................................ I-iii Finding Related Documentation................................................................................................................................................................... I-iii Technical Support................................................................................................................................................................................................ I-v Warranty and Service Policies.............................................................................................................................................................................. I-vi 1.0 Introduction......................................................................................................................................................................................................................... 1-1 1.1 OBR3650HP Overview.......................................................................................................................................................................................... 1-1 1.2 Specifications........................................................................................................................................................................................................... 1-2 2.0 Installation........................................................................................................................................................................................................................... 2-1 2.1 Unpacking the Unit................................................................................................................................................................................................ 2-1 2.2 Mounting the OBR3650HP.................................................................................................................................................................................. 2-1 2.2.1 Water Proof the Connection................................................................................................................................................................. 2-6 2.3 Installing the Grounding Apparatus............................................................................................................................................................. 2-7 2.3.1 Lightning Protection................................................................................................................................................................................. 2-7 2.3.2 Power Surge Protection......................................................................................................................................................................... 2-9 2.3.3 Grounding the Base Station................................................................................................................................................................. 2-10 3.0 Getting Started with OBR3650HP............................................................................................................................................................................ 3-1 3.1 Before You Begin.................................................................................................................................................................................................... 3-1 3.2 Overview of Configuration..…

Text truncated - open the document above for the full version.

3 CHAPTER obr3650hp_ml_r01_sdApproved: D.W. 3-1 3.0 Getting Started with OBR3650HP 3.1 Before You Begin The OBR3650HP provides the base station component of the Vecima VistaMAX system. To set up and configure the base station, you require the following: •One VistaMAX OBR3650HP base station with a stand-alone Power over Ethernet (PoE) or WES800 Ethernet Switch •One VistaMAX outdoor subscriber station or indoor subscriber station such as the OSR3500C or ISR3510. •One of the following components to provide the DHCP and TFTP server: – Vecima’s Network Management 8000 – A third-party DHCP and TFTP server as per the WiMAX standard. This setup is not covered in this manual. Setting up the system using NMS8000 Using the NMS8000 as the provisioning tool for all OSR subscriber stations and hosts on the VistaMAX system is the most common scenario. The platinum, gold, silver, or bronze VistaMAX starter kits available from Vecima Networks includes an NMS8000. NOTE If you wish to connect Internet-accessible hosts to the VistaMAX system, you will need to provide a router with a public IP address and a valid DNS server. When you are connecting to Internet-accessible host and using the NMS8000, Vecima recommends connecting one of the NMS8000 Ethernet interfaces on a public routeable IP address. Figure 3-1 Using NMS8000 to Provision VistaMAX System obr3650hp_ml_r01_sdApproved: D.W. 3-2 3.2 Overview of Configuration The following steps outline the process for configuring a VistaMAX system. This process assumes that you are using an NMS8000. Step 1Use CAT5 straight-through Ethernet cables to connect the physical components as shown in Using NMS8000 to Provision VistaMAX System. Step 2Use the Web-based interface to configure the IP addresses for the base station and subscriber station(s). If necessary, configure the IP addresses for the NMS8000. Step 3Use the Web-based interface to configure the radio parameters for the base station and subscriber station(s). Step 4If necessary, use the Web-based interface for the NMS8000 to add the subscriber stations on the NMS8000. Step 5Establish the link between the base stations and subscriber stations and verify that the subscriber stations are online. The steps that pertain to the base station are described in more detail below. For more information, refer to the NMS8000 & NMS8000/SSP Network Management Server Installation and Operation Guide or related information listed underFinding Related Documentation on page iii. obr3650hp_ml_r01_sdApproved: D.W. 3-3 3.3 Using the Web Based Interface The Web interface of the OBR3650HP system may be viewed with a standard web browser such as Mozilla™ or Internet Explorer™, no additional add-ins are required. NOTE If your Web certificate is invalid or expired, you will be prompted to continue without the certificate or add an exemption to the certificate. The following are the default log on settings for the Base station Web-based interface: •Web-based interface access — https://192.168.101.2 •subnetwork mask — 255.255.255.0 •username — root •password — vistamax To log on to the Web-based interface: Step 1Open a Web browser and open the Web-based interface by typing https://192.168.101.2 in the address bar. The Network Password page opens: NOTE 192.168.101.2 is the default IP address that comes preconfigured from Vecima, but your IP address might be different. If you are not using the default address, contact your system administrator for the IP address. Step 2Type the username root and the password vistamax to access the web GUI. The log on screen displays: obr3650hp_ml_r01_sdApproved: D.W. 3-4 3.4 Configuring the Network You will need to configure your network to establish communication between the network elements. Figure 3-2 shows an example of a properly configured network. The example shows a network configuration using default values. If you purchased a WiMAX starter kit, these value will already be set. The VistaMAX Base Station is shipped with a default IP address. However, depending upon your network configuration, you may want to change the IP address of your Base Station. Figure 3-2 Network Diagram As per the WiMAX standard, the subscriber station requires an IP address and TFTP offered to it during network entry. To fulfill this requirement, both a DHCP and TFTP server must be present. It is possible to use a third-party customer- supplied DHCP and TFTP server, but Vecima recommends using the Network Management Server 8000 (NMS8000). Most Vecima starter kits come with an NMS as part of the solution. NOTE Customers who purchased the basic starter kit or who do not have an NMS must use the WiMAX-out-of-the-box (WOOTB) procedure. For more information about WOOTB, contact the Application Engineering Support at Vecima Networks. To configure a network using NMS8000: Step 1Open the base station graphical user interface (GUI) and click Configuration > Network Configuration. The Current Interfaces screen opens displaying the name, IP address, and netmask of the base station’s primary interface. The default value is 192.168.101.2. To modify this value, click br0 to open the BR0 configuration screen and type the new value in the appropriate field. See “To change the base station IP address“ below for a detailed description of this Step. Step 2Using the NMS GUI, set up and enable DHCP on the NMS, then configure the subscriber stations and host computers as required. NOTE For more information see the NMS8000 & NMS8000/SSP Network Management Server Installation and Operation Guide. obr3650hp_ml_r01_sdApproved: D.W. 3-5 To change the base station IP address: Step 1Log on to the Web-based interface and click Configuration > Network Configuration. The Current Interfaces table displays showing the primary (br0) IP address and virtual addresses (br0:1 br0:2, etc) for your base station. From this page, you can set the following parameters: Step 2Click the br0 link under Name field in the Current Interfaces table. The window will change …

Text truncated - open the document above for the full version.

To: Carlos Bonilla Subject: reply to correspondence reference number 37438 Form 731 confirmation number: EA595202 Date: 2009-05-28 The professional installation document describes how to set the power for the two types of channel bandwidths thereby complying with FCC rules on maximum power. Please refer to the attached installation document provided by applicant. If there are any questions or concerns in this matter, please feel free to contact us at [email protected] Thank you and have a good day. Best Regards, Vicky Lo Document Writer

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 90 SUBPART Z TEST AND MEASUREMENT REPORT For Vecima Networks Inc. 150 Cardinal Place,Saskatoon, SK, Canada S7L 6H7 FCC ID: OPPOBR3650HP Model: VistaMax OBR3650/HP+ Report Type: Original Report Product Type: 3.65 GHz WiMax Base Station Transceiver Test Engineer: Jack Liu Report Number: R0902203-90 Report Date: 2009-03-24 Reviewed By: Daniel Deng Senior RF Engineer Prepared By: (18) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Ave Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732 9164 Vercima Networks Inc. FCC ID: OPPOBR3650HP Report No.: R0902203-90 Page 2 of 57 FCC Part 90 Test Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 MECHANICAL DESCRIPTION.........................................................................................................................................4 OBJECTIVE...................................................................................................................................................................5 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................5 TEST METHODOLOGY..................................................................................................................................................5 MEASUREMENT UNCERTAINTY....................................................................................................................................5 TEST FACILITY.............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................7 JUSTIFICATION.............................................................................................................................................................7 EQUIPMENT MODIFICATIONS.......................................................................................................................................7 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS........................................................................................................7 POWER SUPPLY INFORMATION.....................................................................................................................................7 INTERFACE PORTS AND CABLING.................................................................................................................................7 TEST SETUP BLOCK DIAGRAM.....................................................................................................................................8 SUMMARY OF TEST RESULTS.............................................................................................................................10 §1.1310, §2.1091 & §90.1335 – RF EXPOSURE .......................................................................................................11 APPLICABLE STANDARDS...........................................................................................................................................11 MPE PREDICTION......................................................................................................................................................11 CONCLUSION..............................................................................................................................................................12 §2.1046 & §90.1321– POWER AND ANTENNA LIMITS ......................................................................................13 APPLICABLE STANDARD............................................................................................................................................13 TEST PROCEDURE......................................................................................................................................................13 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................13 ENVIRONMENTAL CONDITIONS..................................................................................................................................13 TEST RESULTS...........................................................................................................................................................14 §90.1321–PEAK EIRP POWER DENSITY ..............................................................................................................15 APPLICABLE STANDARD............................................................................................................................................15 TEST PROCEDURE......................................................................................................................................................15 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................15 ENVIRONMENTAL CONDITIONS...................................................................................…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 90 SUBPART Z TEST AND MEASUREMENT REPORT For Vecima Networks Inc. 150 Cardinal Place,Saskatoon, SK, Canada S7L 6H7 FCC ID: OPPOBR3650HP Model: VistaMax OBR3650/HP+ Report Type: Original Report Product Type: 3.65 GHz WiMax Base Station Transceiver Test Engineer: Jack Liu Report Number: R0902203-90 Report Date: 2009-03-24 Reviewed By: Daniel Deng Senior RF Engineer Prepared By: (18) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Ave Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732 9164 Vercima Networks Inc. FCC ID: OPPOBR3650HP Report No.: R0902203-90 Page 2 of 57 FCC Part 90 Test Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 MECHANICAL DESCRIPTION.........................................................................................................................................4 OBJECTIVE...................................................................................................................................................................5 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................5 TEST METHODOLOGY..................................................................................................................................................5 MEASUREMENT UNCERTAINTY....................................................................................................................................5 TEST FACILITY.............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................7 JUSTIFICATION.............................................................................................................................................................7 EQUIPMENT MODIFICATIONS.......................................................................................................................................7 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS........................................................................................................7 POWER SUPPLY INFORMATION.....................................................................................................................................7 INTERFACE PORTS AND CABLING.................................................................................................................................7 TEST SETUP BLOCK DIAGRAM.....................................................................................................................................8 SUMMARY OF TEST RESULTS .............................................................................................................................10 §1.1310, §2.1091 & §90.1335 – RF EXPOSURE .......................................................................................................11 APPLICABLE STANDARDS...........................................................................................................................................11 MPE PREDICTION......................................................................................................................................................11 CONCLUSION..............................................................................................................................................................12 §2.1046 & §90.1321– POWER AND ANTENNA LIMITS ......................................................................................13 APPLICABLE STANDARD............................................................................................................................................13 TEST PROCEDURE......................................................................................................................................................13 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................13 ENVIRONMENTAL CONDITIONS..................................................................................................................................13 TEST RESULTS...........................................................................................................................................................14 §90.1321–PEAK EIRP POWER DENSITY ..............................................................................................................15 APPLICABLE STANDARD............................................................................................................................................15 TEST PROCEDURE......................................................................................................................................................15 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................15 ENVIRONMENTAL CONDITIONS..................................................................................…

Text truncated - open the document above for the full version.