ORF-VISTARF ID Tag Reader

3/Vista Series Blending and Non-blending Suction Pumps and Remote Dispensers READ THIS MANUAL BEFORE YOU BEGIN Dispensers have both electricity and a hazardous, flammable and potentially explosive liquid. Failure to follow the below precautions and the Warning and Caution instructions in this manual may result in seri- ous injury. Follow all rules, codes and laws that apply to your area and installation. SAFETY PRECAUTIONS - INSTALLATION AND MAINTENANCE Always make sure ALL power to the dispenser is turned OFF before you open the dispenser cabinet for maintenance. Physically lock, restrict access to, or tag the circuit breakers you turn off when servicing the dispenser. Be sure to trip (close) the emergency valve(s) under the dispenser BEFORE beginning maintenance. Make sure that you know how to turn OFF power to the dispenser and submersible pumps in an emer- gency. Have all leaks or defects repaired immediately. EQUIPMENT PRECAUTIONS Be sure to bleed all air from product lines of remote dispensers and prime suction pumps before dispensing product, otherwise, damage to the equipment may occur. Always use the approved method for lifting the dispenser. Never lift by the nozzle boot, sheet metal, valance, etc., otherwise equipment damage or per- sonal injury may occur. HOW TO CONTACT WAYNE Trouble with the installation and operation of the dispenser should be referred to your authorized Wayne service personnel or Wayne Technical Support (1-800-926-3737). INDICATORS AND NOTATIONS Danger indicates a hazard or unsafe practice which, if not avoided, will result in severe injury or possibly death. Warning indicates a hazard or unsafe practice which, if not avoided, may result in severe injury or possibly death. Caution indicates a hazard or unsafe practice which, if not avoided, may result in minor injury. NOTE: Important information to consider, otherwise, improper installation and/or damage to compo- nents may occur. DANGER DANGER WARNING CAUTION March 2003Part No. 920365 Rev B 3/Vista Series Blending and Non-Blending Suction Pumps and Remote Dispensers Installation & Operation Part No. 920365 Rev BMarch 2003 Table of Contents TitlePage iii June 2003Part No. 920365 Rev B 1INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1Dispensers Covered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2Local, State, and Federal Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.3Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1Inspect the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2Island Construction, Dispenser Anchoring, and Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3Vapor Return Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.4Check Valves (Suction Pumps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.5Connecting More Than One Pump to a Tank (Suction Pumps) . . . . . . . . . . . . . . . . . . . . 7 2.6Lifting and Installing the Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.7Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.2 Full Service (Stand-Alone) Dispenser Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.3 Submersible Pump Control Relays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.4 Multiple Dispenser Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.5 Dispenser to Wayne Control System Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.7.6 Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.7.7 Non-Dispenser Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.8Sale Display Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.9Hose Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.10Bleeding Product Lines (Remote Dispensers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.11Priming Suction Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.12Above Ground Storage Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.13Meter Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.14Balance Vapor Recovery System Installation Requirements . . . . . . . . . . . . . . . . . . . . . 16 2.14.1 Dynamic Back Pressure Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.14.2 Back Pressure System Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.15Wayne Vac Vapor Recovery System Installation Requirements . . . . . . . . . . . . . . . . . . 17 2.15.1 Dispenser Vacuum Decay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.15.2 Wayne Pressure/Vacuum Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3START-…

Text truncated - open the document above for the full version.

47 March 2003Part No. 920365 Rev B 5OPERATOR MAINTENANCE 5.1 Preventive Maintenance The safety precautions described in Section 1.3 apply to the following preventive maintenance procedures. A correctly installed dispenser, given proper preventive maintenance attention, will seldom require emergency service. Perform the following checks on a regular basis: •Check the dispenser for internal and external leaks regularly. Check nozzles, swivels, hoses, filters, and joints for leaks and wear. Have all defects repaired immediately. •Do not abuse the hose by trying to stretch it to reach an automobile. This will cause early failure at the cou- plings. •Keep the dispenser clean at all times. Use only mild soap and water with a soft cloth. Do not use gasoline or other petroleum-based products to clean the dispenser. Do not use abrasive cleaners on any part of the dis- penser. All stainless steel surfaces require polishing with a non-abrasive silicone wax a minimum of three times per year to maintain a bright finish and prevent corrosion. If it is necessary to just wipe off the dis- penser, use a damp cloth. See Section 5.3 for additional information on cleaning and corrosion prevention. NOTE:Do not spray the dispenser with water. •Before removing the bezel, wipe off any water lying along the top edge of the dispenser so it will not run inside when the bezel is removed. •If the bezels must be removed during rainy weather, take care to prevent rain from getting inside the dispenser. •Test the tank for water regularly. Water in petroleum is not only a source of engine trouble but will also cause damage to the dispenser. •Check the nozzle boot switch operation. If this does not operate easily, too much force may be applied on the switch mechanisms, causing premature failure. •Periodically check and lubricate all key lock cylinders and locking mechanisms. 5.2 Strainer/Filter A dirty strainer screen and/or fuel filter will slow down the delivery of product. See Figure 2-3 for location. If the underground installation is new, it may be necessary to replace the filter and clean the strainer screen two or three times during the first few days of operation to remove installation debris and pipe sealant. After this, filter replacement and strainer cleaning should be performed periodically. WARNING Before removing the filter and strainer turn the power to the dispenser and submersible pump(s) off and close the emergency shut-off valves on the dispenser being serviced. Failure to do so may result in a haz- ardous condition that can result in serious injury. Loosen strainer cap or spin-on filter slightly and allow gasoline to drain into a plastic container until pressure is relieved. Return product to the appropriate under- ground tank. 48 Part No. 920365 Rev BMarch 2003 5.1 Preventive Maintenance, continued •The fuel filter is removed by unscrewing it (the same way an oil filter is removed from a car engine). Place a container under the filter to catch the product and sediment. To install the new filter, first apply a film of oil to the gasket and hand turn until gasket contacts base, then tighten one half turn. Open the emergency shut-off valve(s), turn the electrical power ON and check for leaks. •Remove the strainer for cleaning by unscrewing the filter (or cap) and then pulling out the strainer. Place a container under the filter or cap to catch the petroleum and sediment. Wash the screen in gasoline and dislodge lint and other foreign particles with compressed air. Install the clean strainer and a new filter. Open the emergency shut-off valve(s), turn the electrical power ON and check for leaks. NOTE:Replacement fuel filters must be UL recognized. 5.3 Cleaning And Corrosion Prevention Instructions To properly care for your dispenser: Step 1Wash the dispenser frequently with a non-abrasive cloth and warm water mixed with a mild household cleaner (such as dishwashing liquid). The dispenser should then be wiped down with a clean damp cloth. Do not use a hose to rinse off the dispenser. NOTE:Do not direct pressurized water (even from a garden hose) at the dispenser. Under no circumstances should power washers be used to clean the dispensers. This can force water into the electronic head and cause damage to the electronic components in the dispenser rendering it inoperative. Do not use all-purpose cleaners on the surfaces of the dispenser. They may scratch the clear plastic, as well as break down the corrosion resistance of painted and stainless steel surfaces. NOTE:Do not use gasoline or other petroleum-based products to clean the dispenser. Step 2 Exposure to contaminants can cause a discoloration of the stainless steel panels (doors, column covers, etc.). If the discoloration persists after washing (as instructed above), the use of an abrasive powder cleaner is very effective in restoring the original shine. Step 3Two cleaners in particular are very effective and practical to use: Zud Heavy Duty Cleaner and Bar Keepers Friend. They can both be found in most hardware/grocery stores. Follow the manufacturers’ instructions for use and always rub in the direction of the brush finish to prevent scratching the stainless steel. Periodic waxing of the dispenser surfaces is essential to maintain the original finish and inhibit corro- sion. Stainless steel surfaces should be polished with a non-abrasive silicone wax. Painted surfaces should be waxed with an automotive wax or polish. We recommend that these surfaces be waxed or polished at least three times a year. 49 March 2003Part No. 920365 Rev B 5.4 Vapor Recovery All hoses, nozzles, breakaways, etc., must be CARB certified for use on Wayne vapor recovery dis- pensers. 5.4.1 Wayne Vac See Section 2.15 and the Compliance Testing and Preventative Maintenance manual, p/n 917947. 5.4.2 Balance Tears and slits and the balance nozzle vapor bellows will cause the vapor system to be in non-compliance. Replace or repair the nozzles as necessary. The bellows face-plate (wh…

Text truncated - open the document above for the full version.

06206-10 Vista Information to User per FCC 15.21 (To be added under the existing FCC information.) Warning! Any change or modification to the electronics of this product not expressly approved by Dresser Wayne could void the user's authority to operate the device. ***

06206-10 Vista External Photograph EUT is behind the card slot in the lower center of the photo. EUT antenna is located to the left of the card slot. ***

Label Location Photograph (FCC/IC label is located at bottom of the cabinetry, the third label from the left.)

06206-10 Vista, Label Artwork

1601 FM 1460, Suite B Round Rock, TX 78664 e-mail: [email protected] (512)244-3371 Fax: (512)244-1846 May 30, 2006 Phil Katselnik Dresser Wayne 3814 Jarrett Way Austin, TX 78728 Dear Mr. Katselnik: Enclosed is the Electromagnetic Compatibility Test Report for Dresser Wayne, Vista. This report can be utilized to demonstrate compliance with FCC Part 15, Class B. If you have any questions, please contact me. Sincerely, Michael A. Royer EMC Department Manager Enclosure Project 06206-10 Dresser Wayne Vista Electromagnetic Compatibility Test Report Prepared for: Dresser Wayne 3814 Jarrett Way Austin, TX 78728 By Professional Testing (EMI), Inc. 1601 FM 1460, Suite B Round Rock, Texas 78664 MAY 30, 2006 Reviewed by Written by Michael Royer EMC Department Manager Eric Lifsey EMC Engineer 06206-10 May 30, 2006 Page 2 of 28 TABLE OF CONTENTS Title Page ...................................................................................................................................................... 1 Table of Contents.......................................................................................................................................... 2 Certificate of Compliance............................................................................................................................. 5 1.0 EUT Description ..................................................................................................................5 1.1 Applicable Rule Parts ......................................................................................................5 1.2 EUT Operation.................................................................................................................5 1.3 Test Facility......................................................................................................................5 2.0 Powerline Conducted Emissions..........................................................................................6 2.1 Test Procedure .................................................................................................................6 2.2 Test Criteria .....................................................................................................................6 2.3 Test Results ......................................................................................................................6 2.4 Test Equipment ................................................................................................................7 3.0 Carrier Field Strength...........................................................................................................7 3.1 Test Procedure .................................................................................................................7 3.2 Test Criteria .....................................................................................................................7 3.3 Test Results ......................................................................................................................7 3.4 Test Equipment ................................................................................................................8 4.0 Spurious and Harmonic Radiated Emissions .......................................................................8 4.1 Test Procedure .................................................................................................................8 4.2 Test Criteria .....................................................................................................................8 4.3 Test Results ......................................................................................................................8 4.4 Test Equipment ................................................................................................................9 5.0 Frequency Tolerance ............................................................................................................9 5.1 Test Procedure .................................................................................................................9 5.2 Test Criteria .....................................................................................................................9 5.3 Test Results ......................................................................................................................9 5.4 Test Equipment ................................................................................................................9 6.0 Emissions Mask ...................................................................................................................9 6.1 Test Procedure .................................................................................................................9 6.2 Test Criteria ...................................................................................................................10 6.3 Test Results ....................................................................................................................10 7.0 Occupied Bandwidth..........................................................................................................10 7.1 Test Procedure ...............................................................................................................10 7.2 Test Criteria ...................................................................................................................10 7.3 Test Results ....................................................................................................................10 7.4 Test Equipment ..............................................................................................................10 8.0 Modifications .....................................................................................................................11 06206-10 May 30, 2006 Page 3 of 28 TABLE OF FIGURES FIGURE 1 Conducted Emissions Test Setup ...............................…

Text truncated - open the document above for the full version.

06206-10 Vista Setup Photographs Conducted Spurious Fundamental Frequency Stability