OTM-8741520-24GTXR/C T-Rex

Fig. 3 Transmitter Fig. 4 Dinoz Light, Sound & Smoking Effect Forward / Turning 2.4 GHz Signal Light Transmitter - Battery Installation Fig. 2 For Dinoz (Fig. 1 and Fig. 2) 1. Switch the power button to OFF position 2. Unscrew the battery cover 3. Open the battery cover 4. Install 4 new 1.5V”AA” batteries with correct polarities (+/-) 5. Close the battery cover 6. Tighten the screw on the battery cover For Transmitter (Fig. 3 and Fig. 4) 1. Unscrew the battery cover 2. Open the battery cover 3. Install 2 new 1.5V “AA” batteries with correct polarities (+/-) as shown inside the battery compartment 4. Close the battery cover 5. Tighten the screw on the battery cover Fig. 5Fig. 6 Fig. 7Fig. 8 Fig. 1 2. Open the water tank cap on the Dinoz. (Fig.6)1. Please prepare a cup of clear tap water. Keep squeezing and releasing the provided water pump to fill up with the water. (Fig.5) 3. Squeeze the provided water pump to fill the water tank into the Dinoz. (Fig.7) 4. Close the water tank cap firmly. (Fig.8) 87411 Contents RC Dinoz x 1 Transmitter x 1 Water Pump x 1 Instruction Manual x 1 Battery Precaution 1. Alkaline batteries are recommend 2. Only batteries of the same or equivalent type as recommended are to be used 3. Do not mix alkaline, standard, or rechargeable batteries 4. Do not mix old and new batteries or different types of batteries 5. Non-rechargeable batteries are not to be charged 6. If rechargeable batteries are to be used, they are only to be charged under adult supervision 7. Rechargeable batteries are to be removed from the product before they are charged 8. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions 9. Remove all batteries from the Dinoz and Transmitter when not in use 10. Exhausted batteries are to be removed from the product 11. The supply terminals are not to be short-circuited 12. Dispose of batteries properly / do not dispose the batteries in fire - it may cause them to explode or leak causing injury or damage 13. Battery installation and removal must only be done by an adult Battery Requirement 1. RC Dinoz: 4 x 1.5V AA batteries 2. Transmitter: 2 x 1.5V AA batteries Battery Installation How to fill RC Dinoz with water for smoking effect 4 x AA For Dinoz (Included for try-me) 2 x AA For Transmitter (Not Included) Dinoz PRO. SYSTEM age 3 TRY ME OFF/ON 1.5V AA + _ _ _ + + + 1. Switch OFF the Dinoz and Switch ON to re-start. 2. Re-install batteries to the transmitter. 3. The transmitter signal light will flash for 7-8 seconds. 4. After the LED light of the transmitter stops flashing, the pairing process is complete for playing. 5. If pairing cannot be completed within 8 seconds, please turn off the Dinoz and re-start the pairing process. 6. When the pairing process is done, whenever switching the Dinoz on and off, it searches for the code that is memorized and will only lock on to the transmitter signal contained that code. 7. If the pairing signal disconnected, please turn off the Dinoz and re-install the batteries in the transmitter. The pairing process will be completed after turning on the Dinoz again. 3. Press the right button of the transmitter for light, sound and smoking effect 4. Play on a smooth surface for the optimal performance 5. Remember to switch OFF the power of the Dinoz after playing 6. The optimal control range is up to 15M (49 ft) indoors 2. Press the left button of the transmitter to control the Dinoz forward or turning movement 1. Turn on the Dinoz Dinoz Light, Sound & Smoking Effect Forward + Randomly Turning Forward Turning Light, Sound & Smoking Effect TRY ME OFF/ON 87411 How to play KT-RM-06/09/19 Conforms to the safety requirements of ASTM F963 Trouble shooting for 2.4GHz pairing in case of no signal The packaging and instruction manual contain important information. Please keep them for future reference. We reserve the right to improve/amend specifications and colors without notice. FCC Label Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RSS-210 Compliance Statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device . Declaration of Conformity The product is in conformity with the requirement of EU Di…

Text truncated - open the document above for the full version.

87415 PRO. SYSTEM age 3 Battery installation How to fill with water for smoking effect Contents RC T-Rex x 1 Water Pump x 1 Range RC Transmitter x 1 15M / 49FT Fig. 3 Transmitter Fig. 4 3 x AA For T-Rex (Included for try-me) 2 x AA For Transmitter (Not Included) T-Rex Light, Sound & Smoking Effect Forward Movement 2.4 GHz Signal Light Transmitter - Battery Installation Fig. 2 2.4G RADIO CONTROL T-REX NO.: 84087 Instruction Manual - RC T-Rex x 1 - RC Transmitter x 1 - Water Pump x 1 - Instruction Manual x 1 1. Alkaline batteries are recommend 2. Only batteries of the same or equivalent type as recommended are to be used 3. Do not mix alkaline, standard, or rechargeable batteries 4. Do not mix old and new batteries or different types of batteries 5. Non-rechargeable batteries are not to be charged 6. If rechargeable batteries are to be used, they are only to be charged under adult supervision 7. Rechargeable batteries are to be removed from the product before they are charged 8. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions 9. Remove all batteries from the T-Rex and Transmitter when not in use 10. Exhausted batteries are to be removed from the product 11. The supply terminals are not to be short-circuited 12. Dispose of batteries properly / do not dispose the batteries in fire - it may cause them to explode or leak causing injury or damage 13. Battery installation and removal must only be done by an adult For T-Rex (Fig. 1 and Fig. 2) 1. Switch the power button to OFF position 2. Unscrew the battery cover 3. Open the battery cover 4. Install 3 new 1.5V “AA” batteries with correct polarities (+/-) 5. Close the battery cover 6. Tighten the screw on the battery cover For Transmitter (Fig. 3 and Fig. 4) 1. Unscrew the battery cover 2. Open the battery cover 3. Install 2 new 1.5V “AA” batteries with correct polarities (+/-) as shown inside the battery compartment 4. Close the battery cover 5. Tighten the screw on the battery cover Fig. 1 Fig. 5Fig. 6 Fig. 7Fig. 8 T-Rex 2. Open the water tank cap on the T-Rex. (Fig.6)1. Please prepare a cup of clear tap water. Keep squeezing and releasing the provided water pump to fill with the water. (Fig.5) 3. Squeeze the provided water pump to fill the water tank into the T-Rex. (Fig.7) 4. Close the water tank cap firmly. (Fig.8) 87415 The packaging and instruction manual contain important information. Please keep them for future reference. We reserve the right to improve/amend specifications and colors without notice. 3. Press the right button of the transmitter for light, sound and smoking effect 4. Play on a smooth surface for optimal performance 5. Remember to switch OFF the power of the T-Rex after playing 6. The optimal control range is up to 15M / 49FT 1. Plug the T-Rex tail in the body. Switch ON the T-Rex 2. Press the left button of the transmitter to control the T-Rex moving forward FCC Label Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RSS-210 Compliance Statement: This device complies with Industry Canada Licence-exempt RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada,. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Declaration of Conformity The product is in conformity with the requirement of EU Directive 2014/53/EU. Environmental Notes: The whole product also does not belong to household waste at the end of the product life. You can return it at collection points for the recycling of electronic and electronical instruments The symbol on the item, instruction manual, hangtag or packing is showing this clearly. Materials should be recycled according to their respective markings. Recycling of old devices or other re-use of materials contained therein represents an important contribution to environmental protection. Please ask at your local community for the correct collection point. Disposal of Batteries Batteries should not be disposed of in the household waste. As the consumer you are le…

Text truncated - open the document above for the full version.

2.4GT POWER SUPPLY 12MHz

Letter of Agency "I, an officer of Kidztech Toys Manufacturing Ltd. do hereby authorize Intertek Testing Services (Mr. Terry Chan / Koo Wai Ip / Kenneth Wong) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and Part 18 of the FCC Rules until further notice." I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.,862. Dated this day of 20 By Signature Printed Name Title Remark: The person who signs this authorization letter must be the grantee contact of record in the Grantee Code data base. Dec 2013 Eric Ho Senior Manager 20May 20

INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (External) INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (External)

INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (Internal) INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (Internal) INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (Internal) INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (Internal) INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Equipment Photographs (Internal)

Technical Description The Equipment Under Test (EUT), is a portable 2.4GHz Transmitter (Controller Unit) for a RC Dinosaur. The sample supplied operated on 68 channels, normally at 2408 - 2475MHz. The channels are separated with 1MHz spacing. The EUT is powered by 2 x 1.5V AA batteries. After switching on the EUT, the dinosaur will be moved forward or backward and turned left and right based on the switches pressed in the controller. Antenna Type: Internal, Integral antenna Antenna Gain: 0dBi Nominal rated field strength is 100.8dBμV/m at 3m (Peak), 77.5dBμV/m at 3m (Average) Maximum allowed production tolerance: +/- 3dB The brief circuit description is listed as follows: 1. U1 acts as MCU 2. Y1 acts as 12MHz Oscillator 3. C4, C5, C9 and L1 act as antenna matching circuit

Analysis Report The Equipment Under Test (EUT), is a portable 2.4GHz Transmitter (Controller Unit) for a RC Dinosaur. The sample supplied operated on 68 channels, normally at 2408 - 2475MHz. The channels are separated with 1MHz spacing. The EUT is powered by 2 x 1.5V AA batteries. After switching on the EUT, the dinosaur will be moved forward or backward and turned left and right based on the switches pressed in the controller. Antenna Type: Internal, Integral antenna Antenna Gain: 0dBi Nominal rated field strength is 100.8dBμV/m at 3m (Peak), 77.5dBμV/m at 3m (Average) Maximum allowed production tolerance: +/- 3dB According to the KDB 447498: Based on the maximum average field strength of production tolerance was 80.5dBμV/m at 3m in frequency 2.475GHz. Thus, it below calculated field strength according to minimum SAR exclusion threshold level as follows: The worst case of SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.483.5) mW = 9.52 mW According to the KDB 412172 D01: EIRP = [(FS*D) ^2*1000 / 30] Calculated Field Strength for 9.52mW is 105dBuV/m @3m Since maximum average field strength plus production tolerance < = 105dBuV/m @3m and antenna gain is > = 0.0dBi, it is concluded that maximum Conducted Power and Field Strength are well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing.

1234 A B C D 4321 D C B A Title NumberRevisionSize A4 Date:12-Jul-2019Sheet of File:E:\托马斯产品\奇士达恐龙\恐龙TXPCB.DDBDrawn By: 3V FB喷烟 VDD F B B F R2 10R 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 U1 * ANT C61UF L1 3.9NH Y1 12M C4 * C5 0.5P C1103 C3103 C2103 R1 10R VDD C8* C7* C9 0.5P IC:6800 频率范围：2408-2475高中低分别为：2408、2440、2475 13脚接地进入测试模式：带调制信号：F切换高中低 2408、2440、2475 11脚接地入测试模式：不带调制信号：F切换高中低 2408、2440、2475 10秒无信号进入睡眠，睡眠电流小于10UA，按任意键唤醒 发射为纯发射无接收功能 LED2 * R3 2.2K LED LED F1后退F2前进 F1 F2 F1 F2 沃尔玛版本 奇士达版本

2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 19 TEST REPORT Report No.: 20060512HKG-001 Kidztech Toys Manufacturing Ltd. Application For Certification (Original Grant) FCC ID: OTM-8741520-24GTX Transmitter Prepared and Checked by: Approved by: Signed On File Lee For Yiu, Florey Assistant Engineer Wong Kwok Yeung, Kenneth Senior Lead Engineer Date: July 13, 2020 TEST REPORT Kidztech Toys Manufacturing Ltd. Intertek Report No: 20060512HKG-001 Page 2 of 19 GENERAL INFORMATION Grantee: Kidztech Toys Manufacturing Ltd. Grantee Address: Room 1201, 12/F., Inter-Continental Plaza, 94 Granville Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Contact Person: Eric Ho Tel: (852) 2721 8868 Fax: (852) 2721 8838 e-mail: N/A Manufacturer: Kidztech Intelligent Technology Co., Ltd. Manufacturer Address: Chengyang Guang Road, Ancheng Road, Liangxia Town, Chenghai District, Shantou City, 515800, Guangdong, China. Brand Name: Kidztech Toys Model: 87415 Additional Model: 87412, 87411 Type of EUT: Transmitter Description of EUT: R/C T-Rex (87415), R/C Dinoz, R/C T-Rex (87412, 87411) Serial Number: N/A FCC ID: OTM-8741520-24GTX Date of Sample Submitted: June 09, 2020 Date of Test: June 09, 2020 to June 22, 2020 Report No.: 20060512HKG-001 Report Date: July 13, 2020 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Conclusion: Test was conducted by client submitted sample. The submitted sample as received complied with the 47 CFR Part 15 Certification. TEST REPORT Kidztech Toys Manufacturing Ltd. Intertek Report No: 20060512HKG-001 Page 3 of 19 SUMMARY OF TEST RESULT Test Specification Reference Results Radiated Emission Radiated Emission on the Bandedge 15.249, 15.209 Pass Radiated Emission in Restricted Bands 15.205 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2019 Edition Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. TEST REPORT Kidztech Toys Manufacturing Ltd. Intertek Report No: 20060512HKG-001 Page 4 of 19 TABLE OF CONTENTS 1.0 GENERAL DESCRIPTION ................................................................................................ 5 1.1 Product Description ................................................................................................... 5 1.2 Related Submittal(s) Grants ....................................................................................... 5 1.3 Test Methodology ...................................................................................................... 5 1.4 Test Facility ................................................................................................................ 5 2.0 SYSTEM TEST CONFIGURATION ..................................................................................... 6 2.1 Justification ................................................................................................................ 6 2.2 EUT Exercising Software ............................................................................................. 6 2.3 Special Accessories .................................................................................................... 6 2.4 Measurement Uncertainty ......................................................................................... 6 2.5 Support Equipment List and Description .................................................................... 6 3.0 EMISSION RESULTS ....................................................................................................... 7 3.1 Field Strength Calculation .......................................................................................... 7 3.2 Radiated Emission Configuration Photograph ............................................................ 8 3.3 Radiated Emission Data ............................................................................................. 8 4.0 EQUIPMENT PHOTOGRAPHS ...................................................................................... 12 5.0 PRODUCT LABELLING .................................................................................................. 12 6.0 TECHNICAL SPECIFICATIONS ....................................................................................... 12 7.0 INSTRUCT…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Configuration Photographs Worst-Case Radiated Emissions (Front View) INTERTEK TESTING SERVICE FCC ID: OTM-8741520-24GTX Configuration Photographs Worst-Case Radiated Emissions (Back View)