PANBT400B0Bluetooth V4.0 Dual-mode dongle

Bluetooth USB Micro Adapter BT – 400 Windows Vista / 7 User’s Manual This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement Th is equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation d istance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 2 Content INSTALLING THE BLUETOOTH STACK .......................................................................3 PAIRING YOUR BLUETOOTH DEVICES.......................................................................7 SENDING DATA FROM YOUR PHONE.......................................................................13 SENDING FILES FROM YOUR PC...............................................................................16 MAKING YOUR PC DISCOVERABLE...........................................................................17 PRINTING TO A BLUETOOTH PRINTER......................................................................19 CONNECTING TO A BLUETOOTH AUDIO ..................................................................19 BLUETOOTH SHARE..................................................................................................20 BLUETOOTH PIM INTERFACE ...................................................................................21 BLUETOOTH DIAL UP ...............................................................................................22 BLUETOOTH OPTIONS..............................................................................................23 BLUETOOTH HARDWARE .........................................................................................24 3 Installing the Bluetooth Stack Note: Before you install, please remove any Bluetooth software and hardware. The installation & driver CD will automatically activate the autorun installation program after you insert the disk into your CD drive. Setup Wizard Screen – AutoPlay Click Yes to continue install. Click Run setup.exe to continue installation. Screen – Preparing installation 4 Choose Agree and Install Bluetooth Software. Screen – Plug Bluetooth device 5 Screen – Welcome to install Bluetooth stack Screen – Installation Completed 6 Using the Bluetooth Stack When you plug in your Bluetooth adaptor for the first time Windows will detect it and install the Bluetooth stack. At this point it will ask you to give your PC a name. This is the name that other devices will see if you make your PC visible to them. Use a name that is memorable. Once the USB adaptor is installed you will see a Bluetooth icon on the task bar at the bottom right of the screen. If you click on it (both right and left click work the same way), you will get a list of options. If you do not have a Bluetooth icon, open up Control Panel -> Hardware & Sound -> Setup a Bluetooth enabled device. Go to the Options Tab and check the final box on the page – Show the Bluetooth icon in the notification area 7 Pairing your Bluetooth devices Pairing is a feature of Bluetooth that allows devices to make secure connections. Although you do not always need to pair devices to exchange data, if you are likely to send information between them on a regular basis it is a good idea to do so. To pair a device using the Bluetooth stack you need to click on the Bluetooth Icon in the task bar and then select Add a Bluetooth Device. Click Add. Read the instructions, and once you’ve done these, check the box My device is set up and ready to be found and press Next. 8 Your PC will then start looking for Bluetooth devices that are discoverable and within range. This may take up to a minute. You will then be given a list of the devices that have been found. If your phone or PDA does not appear on the list then it is probably because it has been set up as hidden or non-discoverable. Dig out the manual (that thing you didn’t get around to reading) and find out how to make it visible. Then try again by pressing Search Again. Once your device has appeared on the list…

Text truncated - open the document above for the full version.

ETC Report No.: 09-06-MAS-236-a Page 1 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. Test Report Of BT-330S-V2 Antenna Company: CC&C Technologies, Inc. Address: 8F, No. 150, Jian Yi Road, Chung Ho City, Taipei County, Taiwan 235, R.O.C. Brand Name: CC&C Device Name: Bluetooth USB Micro Adapter Model No.: BT-330S-V2 Antenna Type: Printed Antenna Operation Frequency: 2402~2480 MHz Test Report No.:09-06-MAS-236-a Date of Testing: 2009/07/02 Test Items: 3D/2D Pattern Measurement Test Laboratory: Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. Test Accessories: Nomenclature Mfg. / Model No ID. No. Double Ridged Guide Horn Antenna EMCO 3115 13057307-001 Network Analyzer H.P. 8753D 43051201-001 Confirm By: Joe Hsieh Section Manager / EMC Dep. I ETC Report No.: 09-06-MAS-236-a Page 2 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. Antenna Structure and Exterior: Antenna Position of BT-330S-V2 test sample: ETC Report No.: 09-06-MAS-236-a Page 3 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. Test Result 3D Pattern 2402MHz 2441MHz ETC Report No.: 09-06-MAS-236-a Page 4 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. 2480MHz ETC Report No.: 09-06-MAS-236-a Page 5 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. 2D Pattern H 2402MHz 2441MHz ETC Report No.: 09-06-MAS-236-a Page 6 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. 2480MHz ETC Report No.: 09-06-MAS-236-a Page 7 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. E1 2402MHz 2441MHz ETC Report No.: 09-06-MAS-236-a Page 8 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. 2480MHz ETC Report No.: 09-06-MAS-236-a Page 9 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. E2 2402MHz 2441MHz ETC Report No.: 09-06-MAS-236-a Page 10 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. 2480MHz ETC Report No.: 09-06-MAS-236-a Page 11 of 11 Electronics Testing Center, Taiwan No.8, Lane 29, Wenming RD., LeShan Tsuen, GuiShan Shiang, Taoyuan County 33383, Taiwan, R.O.C. Antenna Gain Table: Test Frequency (MHz) 2402 2441 2480 Max. Antenna Gain (dBi) -4.10 -4.88 -8.06 Test Setup Photo End of the Report

Registration num ber: W6M21408-14385-C-1 FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Page 18 of 58 3.2 Equivalent isotropic radiated power FCC Rule: 15.247(b)(3) Bluetooth 2.0+EDR EIRP = max. conducted output power + antenna gain EIRP = 8.20 dBm + (-4.10) dBi = 4.10 dBm Limit: EIRP = +36 dBm for Antenna gain <6dBi Bluetooth 4.0 EIRP = max. conducted output power + antenna gain EIRP = 5.26 dBm + (-4.10) dBi = 1.16 dBm Limit: EIRP = +36 dBm for Antenna gain <6dBi Test equipment used: ETSTW-RE 055 3.3 RF Exposure Compliance Requirements RESULT: Test standard : FCC KDB Publication 447498 10 D01v05 According to KDB447498 10 D01v05: SAR evaluation, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. The enclosure of the device provides ≥ 0.5 cm separation from the antenna elements to significant metal parts of the enclosure to minimize potential perturbations. Fr equency Band:2400-2483.5 MHz Maximum Power fed to Antenna (BT2.0): 2.5704 mW Maximum Power fed to Antenna (BT4.0): 1.3062 mW Separation distances: Antenna feed center to metal parts of enclosure: > 5 mm Distance prescribed in user manual: > 5 mm MHz 5 10 15 20 25 mm 2450 10 19 29 38 48 SAR Test Exclusion Threshold (mW) MHz 30 35 40 45 50 mm 2450 57 67 77 86 96 SAR Test Exclusion Threshold (mW) MHz5060708090100110120130140150160170180190mm 24509619629639649659669679689699610961196129613961496 mW

DECLARATION OF CONFORMITY (DoC) Equipment: Bluetooth V4.0 Dual-mode dongle Trademark(s) and Model(s):CC&C / BT-400B0 Manufacturer:Kunshan CC&C Technologies,Co.,LTD. FCC ID in case other parts of this equipment are subject to certification: PANBT400B0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration: Test report number: W6M21408-14385-P-15B Issue date: August 20, 2014 The following manufacturer/importer/entity is responsible for this declaration: Company name: CC&C Technologies, Inc. Name/Title (legal representative): Craig Chen / VICE President R&D Division Address: 8F, No. 150, Jian Yi Road, Zhonghe District, New Taipei City 235 Taiwan Phone: +886-2-8226-5088 Fax: +886-2-8226-5077 E-mail: [email protected] Date: 2014-08-26 Signature:

Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 2 of 15 External Photos Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 3 of 15 Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 4 of 15 Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 5 of 15 Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 6 of 15 Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 7 of 15

Label Label Location 4mm 8mm 透明特多龍印銀字 Bluetooth V4.0 Dual-mode dongle FCC ID: PANBT400B0

Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 8 of 15 Internal Photos Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 9 of 15 Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 10 of 15 Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 11 of 15

of Applicant: CC&C Technologies, Inc. Address: 8F, No. 150, Jian Yi Road, Zhonghe District, New Taipei City 235 Taiwan Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679A-1, IC 5107A A2LA Accredited No.: 2732.01 Report No.: W6M21408-14385-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for Bluetooth V4.0 Dual-mode dongle Model No.: BT-400B0 FCC ID: PANBT400B0 Registration number: W6M21408-14385-C-1 FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 58 TABLE OF CONTENTS 1 GENERAL INFORMATION ..........................................................................................................2 1.1 NOTES..........................................................................................................................................2 1.2 TESTING LABORATORY................................................................................................................3 1.2.1 Location ..............................................................................................................................3 1.2.2 Details of accreditation status ............................................................................................3 1.3 D ETAILS OF APPROVAL HOLDER...................................................................................................3 1.4 A PPLICATION DETAILS.................................................................................................................4 1.5 G ENERAL INFORMATION OF TEST ITEM........................................................................................4 1.6 T EST STANDARDS.........................................................................................................................5 2 TECHNICAL TEST .........................................................................................................................6 2.1 S UMMARY OF TEST RESULTS........................................................................................................6 2.2 TEST ENVIRONMENT....................................................................................................................6 2.3 TEST EQUIPMENT LIST.................................................................................................................7 2.4 G ENERAL TEST PROCEDURE........................................................................................................9 3 TEST RESULTS (ENCLOSURE) ................................................................................................11 3.1 PEAK OUTPUT POWER (TRANSMITTER) ......................................................................................12 3.2 E QUIVALENT ISOTROPIC RADIATED POWER................................................................................18 3.3 RF EXPOSURE COMPLIANCE REQUIREMENTS............................................................................18 3.4 TRANSMITTER RADIATED EMISSIONS IN RESTRICTED BANDS....................................................19 3.5 S PURIOUS EMISSIONS (TX) .........................................................................................................20 3.6 C ARRIER FREQUENCY SEPARATION...........................................................................................26 3.7 N UMBER OF HOPPING FREQUENCIES..........................................................................................29 3.7.1 Pseudorandom Frequency Hopping Sequence .................................................................31 3.7.2 Coordination of hopping sequences to other transmitters................................................31 3.7.3 System Receiver Hopping Capability ...............................................................................31 3.8 T IME OF OCCUPANCY (DWELL TIME) ........................................................................................32 3.9 20DB BANDWIDTH.....................................................................................................................38 3.9.1 System Receiver Input Bandwidth.....................................................................................41 3.10 M INIMUM 6 DB BANDWIDTH.....................................................................................................42 3.11 R ADIATED EMISSION ON THE BAND EDGE..................................................................................45 3.12 P EAK POWER SPECTRAL DENSITY.............................................................................................51 3.13 RADIATED EMISSION FROM DIGITAL PART................................................................................54 3.14 POWER LINE CONDUCTED EMISSION.........................................................................................55 A PPENDIX..............................................................................................................................................58 Registration number: W6M21408-14385-C-1 FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Page 2 of 58 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally confo…

Text truncated - open the document above for the full version.

Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 12 of 15 Set Up Photo of Radiated Emission EMI Below 1GHz Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 13 of 15 Above 1GHz Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 14 of 15 RF Registration number: W6M21408-14385-FCC FCC ID: PANBT400B0 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 15 of 15 Set Up Photo of Conducted Emission