PB2SPT1700WAV ChameleonRF SPT1700

TAKE OUT WHAT YOU NEED INSTALL THE PC CARD CLIENT ADAPTER INSTALL THE APPROPRIATE DRIVER AND UTILITIES 1 2 3 Quick Start Guide CISCO AIRONET 350 SERIES PC CARD C LIENT ADAPTERS Laptops with PC card client adapters Access Point 1 Take Out What You Need If any item is missing or damaged, contact your Cisco representative or reseller for support. Note: The integrated antenna on PC models of the Aironet PC Client Card Adapter is permanently attached; LM models are shipped with no antenna. Additional Requirements •A computing device (desktop personal computer, notebook, laptop computer, portable or hand-held device) equipped with an internal or external PC Card Type II or Type III slot. All drivers and supporting software (card and socket services) for the PC card slot must be loaded and configured. •The following information from your system administrator: —your wireless client name —the (case-sensitive) wireless service set identification (SSID) for your radio network —for Microsoft Windows networking, your computer name and workgroup name —the username and password for your network account —if you are not connected to a DHCP server, the IP address, default gateway address, and subnet mask of your computer —for Windows NT systems, an available IRQ number (interrupt address) in your system Cisco Aironet 350 Series PC Card Client Adapter (labeled Wireless LAN Adapter) Cisco Aironet 350 Series PC Card Client Adapter CDs for Windows 95 and Windows NT or Windows 98 and Windows 2000 with software and product documentation CISCO AIRONET 340 SERIES 11 Mbps WIRELESS LAN ADAPTER 2 Install the PC Card Client Adapter CautionThe following procedures and physical connections apply generally to normal and conventional PC card slots. In cases of custom or non-conventional equipment, be alert to possible differences in PC card slot configurations. 1 Before you begin, examine the PC card client adapter. One end is a dual-row, 68-pin PC card connector. The card is keyed so that it can be inserted only one way into the PC card slot. The slot in your computing device must be a PC card Type II slot (this includes slots that support both the Type II and Type III cards). Note: The PC card slot will be on the left or right side of the computer, depending on the model. 2 For Windows 95 and Windows 98 systems, remove any other PC card from the card slot. 3 For Windows 95 or Windows 98 systems, turn the computer on before inserting the PC card client adapter. For Windows NT systems, turn the computer off before inserting the client adapter. CautionNever force the PC card client adapter into the PC card slot. Forcing it will damage both the PC card and the slot. If the PC card does not easily insert, remove the card and re-insert it. 4 Hold the PC card client adapter with the logo facing up and insert the card into the slot, applying just enough pressure to make sure it is fully seated. Proceed to the appropriate driver installation for your operating system. 3 Note: The following procedures assume you are installing the driver from the CD provided. If your PC does not have a CD-ROM drive, download the driver from Cisco’s web site. Install the Appropriate Driver and Utilities Windows 98 Systems Note: The Windows 98 driver also works with the Windows 2000 operating system. In Windows 98 systems, after you have installed the PC card client adapter, the system automatically detects it, opens a New Hardware Found window, and starts collecting information for a driver database. 1 When the Add New Hardware Wizard dialog box opens, it is searching for new drivers. Click Next. 2 From the next dialog box, select Search for the best driver for your device (Recommended) and click Next. 3 Select CD-ROM drive, deselect all other options, insert the Cisco Aironet 350 Series Client Adapter CD for Windows 98, and click Next. 4 The hardware wizard will find the installation files on the CD and display the search results. When the PCMCIA adapter driver is displayed, click Next to copy the required files. 5 During driver installation, you may be prompted to enter a path to the required client adapter or Windows 98 files: (a) Windows 98 files installed on your PC are usually located in the folder C:\Windows\Options\Cabs. Click OK to install. (b) If the system prompts you for the Windows CD and the CD-ROM drive on your PC is drive D, the path should be D:\WIN98. Click OK to copy the required files. 6 The Add New Hardware Wizard window again opens indicating that the installation is complete. Click Finish. 7 Remove the CD and restart your laptop. 8 When the computer restarts, double-click My Computer, Control Panel, and Network. 9 Select the PCMCIA adapter and click Properties. 10 In the Properties window, click Advanced. 11 In the Advanced window, select Client Name and enter your computer’s unique name in the Value dialog box. 12 Select SSID. Enter your Access Point’s (case-sensitive) SSID in the Value dialog box. Click OK. 4 13 If you are not connected to a DHCP server, double-click My Computer, Control Panel, and Network. Click the Protocols tab and select TCP/IP and Properties. Select Specify an IP address and enter the IP Address, Subnet Mask, and Default Gateway address of your computer. Click OK. 14 In the Network window, click OK. 15 When prompted, click Ye s to reboot the laptop. Windows 95 Systems In Windows 95 systems, after you have installed the PC card client adapter, the system automatically detects it, opens a New Hardware Found window, and starts collecting information for a driver database. 1 The Update Device Driver Wizard dialog box opens and indicates that Windows will complete the installation of the PCMCIA adapter. 2 Insert the Client Adapter CD for Windows 95 and NT, and click Next. 3 When the Update Device Driver Wizard indicates that it is unable to locate a driver, click Other Locations. 4 In the Select other Location window, click Browse. 5 Select the CD-ROM drive and click OK. 6 In the Select other Location win…

Text truncated - open the document above for the full version.

SPT 1700 Series SPT 1700 Series © 1999 - 2001 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliabilit y , function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products. Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Symbol Technologies, Inc. One Symbol Plaza Holtsville, N.Y. 11742-1300 http://www.symbol.com Patents This product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No. 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420; 5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,047,892; 6,050,491; 6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,068,190; 6,082,621; 6,084,528; 6,088,482; 6,092,725; 6,101,483; 6,102,293; 6,104,620; 6,114,712; 6,115,678; 6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379; D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581; D414,171; D414,172, D418,500; D419,548; D423,468; D424,035 D431,158; D430,159; D431,562. Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan). European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713. rev. 09/00 1 Quick Reference Introduction Congratulations on your purchase of Symbol Technologies’ SPT 1700 Series Terminal! The unique combination of pocket size, Personal Information Management software, RF communication via Symbol’s Spectrum24 ® wireless network (SPT 174X) or wide area network (SPT 173X), printing support and 1- and 2- dimensional scanning capability make this product superior for use in a wide range of applications. About This Guide This guide covers the procedures for the basic set up and use of the terminal. Specific topics covered include: •Parts of the SPT 1700 on page 2 •Getting Started with the SPT 1700 on page 4 •Charging the Battery on page 4 •Installing the Battery on page 4 •Starting the SPT 1700 on page 6 •Using the SPT 1700 on page 8 •Using the Contrast Control on page 8 •Writing with the Stylus on page 8 •Icon Descriptions on page 10 •Scanning 1-D Bar Codes with the SPT 1700 on page 12 •Scanning PDF417 (2-D) Bar Codes on page 13 •Initiate A Network Connection on page 14 •Resetting Your SPT 1700 Terminal on page 10 •Maintaining the SPT 1700 on page 14 •Troubleshooting on page 15 •Service Information on page backcover. The SPT 1700 Product Reference Guide (p/n 70-37544-xx), available from Symbol or your Reseller, details the applications available on the SPT 1700. 2 SPT 1700 Series Parts of the SPT 1700 The following illustration indicates each part of the SPT 1700 Te r m i na l . Scroll Button (Up and Down) Laser Decode LED Center Scan Button Scroll Button (Up and Down) Right Scan Trigger LCD (Screen) Calculator Icon Find Icon Applications Icon Menu Icon Contrast Button Power Button Application Buttons Left Scan Tr i g g e r Front View Left View Graffiti Input Area WAN Antenna (SPT 1733/34 only) 3 Quick Reference Parts of the SPT 1700 (continued) Infrared Port Handstrap Connector Lithium-Ion Battery Battery Latch Handstrap Connector Stylus Stylus Silo Battery Latch Battery Compartment Battery Cover Serial PortScanner Exit Window Speaker Bottom View To p V i e w Back View Reset Button 4 SPT 1700 Series Getting Started with the SPT 1700 Before you can use your SPT 1700, perform the basic set up procedures covered on the following pages. Specifically: •Charge and Install the Battery •Start the SPT 1700 •Initiate the network connection (SPT 174X/173X only). Installing the Battery To install the battery in your SPT 1700: 1. Open the latches on the battery cover and lift it away from the SPT 1700. 2. Insert the lithium-ion bat- tery in the battery compart- ment, making sure it snaps into place. 3. Replace the battery cover and re-secure the latches. Note:Be careful to posi- tion the battery latches completely open while se…

Text truncated - open the document above for the full version.

Cisco Systems, Inc. 4125 Highlander Parkway Richfield, Ohio 44286 Phone: 330 523-2094 Fax: 330-523-2002 http://www.cisco.com Phone: (330) 523-2094 Fax: (330) 523-2002 E-Mail: [email protected] October 15, 2003 Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Re: FCC ID: PB2SPT1700 To Whom It May Concern: The following information is to be held confidential pursuant to 47 CFR Part 0 §0.457 and Section 552(b)(4) of the Freedom of Information Act, because the information provided is proprietary and contains trade secrets. If made public, the information might be used to the disadvantage of the Cisco Systems, Inc. in the market place. In addition, this information is to be withheld from the applicant, Wav Inc., as well. Block Diagram Schematic Diagrams Technical Description Best Regards, Jim Nicholson EMC Compliance Engineer

Federal Communications Commission Equipment Approval Services P.O. Box 358315 Pittsburgh, PA 15251-5315 RE: FCC Part 15 Certification of WAV ChameleonRF SPT1700 hand held data terminal FCCID: PB2SPT1700 Date: September 11, 2003 To The Commission: This certification request is for the WAV ChameleonRF Model SPT1700 portable terminal with integrated Cisco Aironet AIR-LMC352 PCMCIA WLAN Module. The SPT1700 is a hand held device and not body worn. No SAR testing has been performed, as this device is hand held and not body worn. The Cisco Aironet AIR-LMC352 wireless LAN PCMCIA adapter has previously been FCC certified under FCCID LDK102040. Form 159 has been electronically paid via credit card. If there are any questions about this request, please contact me at the number below. Thank you for your attention. Respectfully submitted, Charles D. Bolvin Vice President of Technology WAV Inc. [email protected] 630-818-1006 Voice 630-818-4450 FAX

FCC ID: PB2SPT1700 External Photos FCC ID: PB2SPT1700

FCC ID: PB2SPT1700 Internal Photos FCC ID: PB2SPT1700

FCC ID: PB2SPT1700 Antenna Photos FCC ID: PB2SPT1700 FCC ID: PB2SPT1700

FCC ID: LDK102040 Internal Photos

Federal Communications Commission Equipment Approval Services P.O. Box 358315 Pittsburgh, PA 15251-5315 RE: FCC Part 15 Certification of WAV ChameleonRF SPT1700 hand held data terminal FCCID: PB2SPT1700 Date: October 21, 2003 To The Commission: For the Operational Description of the AIR-LMC352 (FCCID: LDK102040) Spread Spectrum Transmitter, please refer to the original Cisco filing on 06/05/2000. If there are any questions about this request, please contact me at the number below. Thank you for your attention. Respectfully submitted, Charles D. Bolvin Vice President of Technology WAV Inc. [email protected] 630-818-1006 Voice 630-818-4450 FAX

October 21, 2003 WAV, Inc. Attn: Mr. Chuck D. Bolvin 245 West Roosevelt Road Building 7, Suite 48 West Chicago, IL 60185 UL Reference: File MC1343, Project 03NK32115 Subject: EMC Test and Measurement Report for Model SPT1700 Dear Mr. Bolvin: We have provided with this letter your EMC Test Report for the above referenced model. The product was determined to comply with the requirements noted in the report. Please review the attached report and direct any questions or comments to me. Samples were returned following testing. We appreciate your interest in UL’s EMC Services, and encourage you to contact us in the future should you need EMC test services. This closes Project 03NK32115. Best regards, Reviewed by: Lou Madjarov (Ext 43957) Jack Steiner EMC Sr. Project Engineer Engineering Group Leader International EMC Services International EMC Services UL International EMC Services 333 Pfingsten Road Northbrook, Illinois 60062-2096 (800) 873-8536 Fax No. (847) 272-8864 http://www.ul.com/emc/ FCC ID: PB2SPT1700 File MC1343 Project 03NK32115 Page 1 of 10 UL International EMC Services www.ul.com/emc (800) USE UL EMC EMC – TEST REPORT Issue Date: October 21, 2003 √ EMISSIONS IMMUNITY Test Report File No. : MC1343 Project No. : 03NK32115 Model / Type : Model SPT1700 Kind of Product : Hand held data terminal with integrated Cisco Aironet AIR-LMC352 PCMCIA WLAN Module Applicant : WAV, Inc. Address : 245 West Roosevelt Road : Building 7, Suite 48 : West Chicago, IL 60185 Manufacturer : Same as Applicant Test Result : COMPLIANT This report without appendices consists of 10 pages. Appendix A contains test photos, Appendix B contains original test data, Appendix C contains sample calculations and Appendix D contains an Block Diagram of the Measurement System. The data contained in this report reflects only the items tested in the configurations and mode of operations described. An attempt has been made to arrange the EUT, with the equipment provided, into a test configuration which maximizes the observed emissions of the EUT while simulating, as close as practical, a typical end-use installation. The photos and data provided in this report document that configuration. Underwriters Laboratories Inc. authorizes the above company to reproduce this report provided it is reproduced in its entirety. Underwriters Laboratories Inc. 333 Pfingsten Rd. Northbrook, IL 60062 Fax: (847) 272-8864 FCC ID: PB2SPT1700 File MC1343 Project 03NK32115 Page 2 of 10 UL International EMC Services www.ul.com/emc (800) USE UL EMC REPORT DIRECTORY SECTION TITLE GENERAL 1.0 General Product Description 1.1 Model Differences 1.2 Environmental Conditions in Test Lab 1.3 Calibration Details of Equipment Used for Measurement 1.4 EUT (Equipment Under Test) Configuration 1.5 Antenna Configuration 1.6 EUT Operating Mode 1.7 Device Modifications EMISSIONS 2.0 Emissions Test Regulations Radiated Electric Field Emissions IMMUNITY 3.0 Immunity Test Regulations CONCLUSION 4.0 General Remarks 4.1 Summary APPENDICIES A Test Setups (Photos, Diagrams and Drawings) B Test Data C Sample Calculations D Antenna Calibration Schedule FCC ID: PB2SPT1700 File MC1343 Project 03NK32115 Page 3 of 10 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.0 GENERAL PRODUCT DESCRIPTION The EUT is a hand held data terminal with integrated Cisco Aironet AIR-LMC352 PCMCIA WLAN Module, FCC ID: LDK102040. 1.0.1 Equipment Mobility: Hand held 1.0.2 Test Voltage and Frequency: Voltage (V) Frequency (Hz) 3.6V DC 1.1 MODEL DIFFERENCES Any other model(s) represented by the models tested in this investigation will be documented by the manufacturer. 1.2 ENVIRONMENTAL CONDITIONS IN TEST LAB Temperature: 20-25 °C Relative Humidity: 30-60% RH Atmospheric Pressure: 860-1060 mbar 1.3 CALIBRATION OF EQUIPMENT USED FOR MEASUREMENT All test equipment and test accessories are calibrated on a regular basis. The maximum time between calibrations is one year or what is recommended by the manufacturer, whichever is less. All test equipment calibrations are traceable to the National Institute of Standards and Technology (NIST), therefore, all test data recorded in this report is traceable to NIST. FCC ID: PB2SPT1700 File MC1343 Project 03NK32115 Page 4 of 10 UL International EMC Services www.ul.com/emc (800) USE UL EMC 1.4 EUT CONFIGURATION(s) See Appendix A for individual set-up configuration(s). In addition to the EUT, the following peripheral devices and/or cables were connected during the measurement: Device Manufacturer Model Serial # FCC ID EUT Symbol Technologies SPT1700 S40a03K117 PB2SPT1700 Modular Transmitter CISCO AIR-LMC352 AMB072918FP LDK102040 1.5 ANTENNA CONFIGURATIONS COVERED Antenna EUT Output Power Antenna Gain Total EIRP Exposure Category OMNI 20dBm (100mW) 0 dBi 20dBm (100mW) Hand Held 1.6 EUT OPERATING MODE(s) The equipment under test was operated during the measurements under the following conditions: Continuous operation. 1.7 DEVICE MODIFICATIONS The following modifications were necessary for compliance: None. FCC ID: PB2SPT1700 File MC1343 Project 03NK32115 Page 5 of 10 UL International EMC Services www.ul.com/emc (800) USE UL EMC 2.0 EMISSIONS TEST REGULATIONS 47 CFR Part 15 Subpart B: 2002 + ANSI C63.4 – 1992 The device was evaluated to 15.247 of CFR 47, Part 15 Since the EUT is identical to a previously certified device except as noted in Section 1.0, only a limited test program was required. Testing was covered / required as noted below: Test / Requirement CFR 47, Part 15 Reference Test Required Notes Conducted emission 15.207 Not Applicable EUT is battery-operated device with no provision for direct connection to AC mains. 6dB Bandwidth 15.247(a)(2) No Considered covered by tests performed on previously certified device. (Cisco) RF Conducted Peak Output Power 15.247(b) No Considered covered by tests performed on previously certified device. (Cisco) Reduced output if directional gain exceeds 6dBi 15.247(b)(3) No Considered covered by tests performed on …

Text truncated - open the document above for the full version.

FCC ID: LDK102040 MFA p0040008, d0050047 Date: May 31, 2000 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Cisco Systems Inc Equipment: AIR-LMC350 FCC ID: LDK102040 FCC Rules: 15.247 and Confidentiality Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. Filing fees are attached. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cvr FCC ID: LDK102040 MFA p0040008, d0050047 LIST OF EXHIBITS (FCCCERTIFICATION(TRANSMITTERS) - REVISED 9/28/98) APPLICANT: Cisco Systems Inc FCC ID: LDK102040 BY APPLICANT: 1. LETTER OF AUTHORIZATION 2. IDENTIFICATION DRAWINGS ID LABEL LOCATION INFO ATTESTATION STATEMENT(S) LOCATION OF COMPLIANCE STATEMENT 3. DOCUMENTATION: 2.1033(b) (3) USER MANUAL(S) (4) OPERATIONAL DESCRIPTION (5) BLOCK DIAGRAM (5) SCHEMATIC DIAGRAM (7) EXTERNAL PHOTOGRAPHS INTERNAL PHOTOGRAPHS PARTS LIST ACTIVE DEVICES 4. DRAFT SPECIFICATION INFORMATION 5. PARTS LIST/TUNE UP INFO BY M.F.A. INC. A. TESTIMONIAL & STATEMENT OF CERTIFICATION B. STATEMENT OF QUALIFICATIONS FCC ID: LDK102040 MFA p0040008, d0050047 Sub-part 2.1033(c): EQUIPMENT IDENTIFICATION FCC ID: LDK102040 NAMEPLATE DRAWING ATTACHED, EXHIBIT 1. LOCATION AS PER LABEL DRAWING(S) DATE OF REPORT May 31, 2000 SUPERVISED BY: Morton Flom, P. Eng. FCC ID: LDK102040 MFA p0040008, d0050047 THE APPLICANT HAS BEEN CAUTIONED AS TO THE FOLLOWING: 15.21 INFORMATION TO USER. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) SPECIAL ACCESSORIES. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. FCC ID: LDK102040 MFA p0040008, d0050047 TABLE OF CONTENTS RULE DESCRIPTION PAGE . Test Report 1 2.1033(c) General Information Required 2 . Standard Test Conditions and Engineering Practices 6 15.247(b). Maximum Peak Output Power 7 15.247(c). Out of Band Emissions 19 15.205. Restricted Bands Of Operation 26 15.247(a)(2). Allowed Occupied Bandwidth 39 15.247(d). Transmitter Power Density 49 15.247(e). Processing Gain (Summary) 49 FCC ID: LDK102040 MFA p0040008, d0050047 PAGE NO.1of53. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) TEST REPORT b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d0050047 d) Client: Cisco Systems Inc. 3875 Embassy Parkway Akron, OH 44333 e) Identification: AIR-LMC350 FCC ID: LDK102040 Description: Unlicensed PCMCIA Direct Sequence Spread Spectrum Transceiver f) EUT Condition: Not required unless specified in individual tests. g) Report Date: May 31, 2000 EUT Received: April 14, 2000 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. FCC ID: LDK102040 MFA p0040008, d0050047 PAGE NO.2of53. LIST OF GENERAL INFORMATION REQUIRED FOR CERTIFICATION IN ACCORDANCE WITH FCC RULES AND REGULATIONS, VOLUME II, PART 2 AND TO 15.247 and Confidentiality Sub-part 2.1033 (c)(1): NAME AND ADDRESS OF APPLICANT: Cisco Systems Inc 170 West Tasman Drive San Jose, CA 95134-1706 MANUFACTURER: Applicant (c)(2): FCC ID: LDK102040 MODEL NO: AIR-LMC350 (c)(3): INSTRUCTION MANUAL(S): PLEASE SEE ATTACHED EXHIBITS (c)(4): TYPE OF EMISSION: (c)(5): FREQUENCY RANGE, MHz : 2412 to 2462 (c)(6): POWER RATING, Watts: 0.1 (conducted all channels, all bit rates) 0.355 (EIRP with Yagi) 0.132 (EIRP with Dipole) 0.117 (EIRP with Snap) Switchable Variable x N/A (c)(7): MAXIMUM POWER RATING, Watts: 1 Watt Conducted 15.203: ANTENNA REQUIREMENT : The antenna is permanently attached to the EUT The antenna uses a unique coupling x The EUT must be professionally installed The antenna requirement does not apply FCC ID: LDK102040 MFA p0040008, d0050047 PAGE NO.3of53. Subpart 2.1033(continued) (c)(8): VOLTAGES & CURRENTS IN ALL ELEMENTS IN FINAL R. F. STAGE, INCLUDING FINAL TRANSISTOR OR SOLID STATE DEVICE: COLLECTOR CURRENT, A = per manual COLLECTOR VOLTAGE, Vdc = per manual SUPPLY VOLTAGE, Vdc = 5 (…

Text truncated - open the document above for the full version.

FCC ID: LDK102040 MFA p0080005, d0080082 PAGE NO.7 of 53. Addendum September 13, 2000 NAME OF TEST: RF Conducted Power SPECIFICATION: 47 CFR 15.247(b) MEASUREMENT DATA MHz Watts Conducted 2412 0.774 2442 0.093 2462 0.081 SUPERVISED BY: Morton Flom, P. Eng.

FCC ID: LDK102040 MFA p0080005, d0080082 PAGE NO.7 of 53. AMENDED August 22, 2000 NAME OF TEST: Maximum Peak Output Power SPECIFICATION: 47 CFR 15.247(b) SPEC. LIMIT:≤1 Watt peak (0.25 if <50 Hopping Channels) TEST EQUIPMENT: Attached MEASUREMENT DATA ANTENNA GAIN, dBi = 0 Snap On PEAK OUTPUT POWER, Watts = 0.0955 EIRP WORST CASE FOR ALL CHANNELS NAME OF TEST: Radiated Emissions g0080488: 2000-Aug-17 Thu 14:16:00 Snap On Antenna FREQUENCY TUNED, MHz FREQUENCY EMISSION, MHz METER, dBuV CF, dB uV/m @ 3m EIRP, dBm EIRP, mw 2412.000000 2413.200000 59.06 55.77 551442.2 19.6 91.2 2442.000000 2443.300000 59.06 55.96 563637.66 19.8 95.5 2462.000000 2463.300000 57.94 56.1 503500.61 18.8 75.9 SUPERVISED BY: Morton Flom, P. Eng. FCC ID: LDK102040 MFA p0080005, d0080082 PAGE NO.9.1 of 53. AMENDED August 22, 2000 NAME OF TEST: Out of Band Emissions g0080487: 2000-Aug-17 Thu 11:10:00 Snap On Antenna FREQUENCY TUNED, MHz FREQUENCY EMISSION, MHz METER, dBuV CF, dB uV/m @ 3m EIRP, dBm MARGIN, dB 2442.000000 30.213000 11.93 14.87 21.88 -68.4 -13.2 2442.000000 34.000000 10.13 14.33 16.71 -70.8 -15.5 2442.000000 38.000000 17.61 13.83 37.33 -63.8 -8.6 2442.000000 42.000000 15.85 13.23 28.44 -66.1 -10.9 2442.000000 46.000000 -0.6 12.54 3.95 -83.3 -28.1 2442.000000 50.120000 11.04 11.88 14 -72.3 -17.1 2442.000000 54.000000 3.73 11.23 5.6 -80.3 -25 2442.000000 58.000000 -2.16 10.6 2.64 -86.8 -31.6 2442.000000 66.000000 -0.5 9.68 2.88 -86 -30.8 2442.000000 69.940000 2.99 9.31 4.12 -82.9 -27.7 2442.000000 74.000000 5.13 9.05 5.12 -81 -25.8 2442.000000 83.000000 10.1 9.04 9.06 -76.1 -20.9 2442.000000 86.000000 18.49 9.38 24.75 -67.4 -12.1 2442.000000 110.000000 10.59 12.97 15.07 -71.7 -19.4 2442.000000 114.550000 15.21 13.37 26.85 -66.6 -14.4 2442.000000 118.000000 10.86 13.67 16.85 -70.7 -18.5 2442.000000 122.000000 7.24 13.9 11.4 -74.1 -21.9 2442.000000 126.000000 14.16 14.04 25.7 -67 -14.8 2442.000000 130.000000 13.58 14.19 24.46 -67.5 -15.2 2442.000000 134.000000 11.51 14.5 19.98 -69.2 -17 2442.000000 138.000000 9.02 14.8 15.52 -71.4 -19.2 2442.000000 142.000000 8.73 14.98 15.33 -71.5 -19.3 2442.000000 144.025000 17.39 15.01 41.69 -62.8 -10.6 2442.000000 146.025000 4.69 15.04 9.69 -75.5 -23.3 2442.000000 150.325000 12 15.09 22.62 -68.1 -15.9 2442.000000 161.950000 7.43 14.89 13.06 -72.9 -20.7 2442.000000 166.000000 6.6 14.82 11.78 -73.8 -21.6 2442.000000 170.000000 6.65 14.74 11.74 -73.8 -21.6 2442.000000 174.000000 7.53 14.79 13.06 -72.9 -20.7 2442.000000 178.000000 7.59 14.85 13.24 -72.8 -20.6 2442.000000 190.000000 23.06 15.95 89.23 -56.2 -4 2442.000000 202.000000 5.78 17.18 14.06 -72.3 -20 2442.000000 212.638000 14.57 18.16 43.3 -62.5 -10.3 2442.000000 216.013000 15.82 18.46 51.76 -60.9 -11.7 2442.000000 218.000000 6.06 18.63 17.16 -70.5 -21.3 2442.000000 222.000000 4.66 18.95 15.15 -71.6 -22.4 2442.000000 226.000000 8.27 19.23 23.71 -67.7 -18.5 2442.000000 230.000000 7.34 19.51 22 -68.4 -19.2 2442.000000 234.000000 7.97 19.63 23.99 -67.6 -18.4 2442.000000 238.000000 12.3…

Text truncated - open the document above for the full version.