PB4-TDKA12Wireless Speaker

63952741-C CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. ATTENTION: Users of this product are cautioned not to make modifications or changes that are not approved by Imation Corp. Doing so may void the compliance of this product and may result in the loss of the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. • The rating information is located at the bottom of the apparatus. 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all Instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. The AC mains plug is used as the power disconnect device and it should remain readily accessible and operable during intended use. In order to completely disconnect the apparatus from power, the mains plug should be completely removed from the AC outlet socket. 16. CAUTION: To reduce the risk of fire or explosion, do not expose batteries to excessive heat such as sunshine, fire or other heat sources. This Class B digital apparatus complies with Canadian ICES-003. SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power surges ARE NOT covered under warranty for this product. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT. This Class B digital apparatus complies with European Union CE – EMC Directive (2004/108/EC) and European Union CE – Low Voltage Directive (2006/95/EC). This Bluetooth module is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). This product is marked with the CE logo and uses radio frequency bands that are harmonized throughout the European Community. IMPORTANT SAFETY INSTRUCTIONS UPOZORNĚNÍ: VZHLEDEM K RIZIKU ÚRAZU ELEKTRICKÝM PROUDEM NEDEMONTUJTE KRYT (NEBO ZADNÍ ČÁST). UVNITŘ NEJSOU ŽÁDNÉ ČÁSTI OPRAVITELNÉ UŽIVATELEM. VEŠKERÉ SERVISNÍ PRÁCE PŘENECHEJTE KVALIFIKOVANÉMU PRACOVNÍKOVI SERVISU. NEBEZPEČNÉ NAPĚTÍ: Symbol blesku se šipkou v rovnostranném trojúhelníku znamená pro uživatele varování před přítomností neizolovaného nebezpečného napětí pod krytem přístroje. Toto napětí může být dostatečně vysoké, aby pro osoby představovalo nebezpečí úrazu elektrickým proudem. POZOR: Symbol vykřičníku v rovnostranném trojúhelníku v tištěných materiálech dodávaných k přístroji upozorňuje uživatele na důležité pokyny týkajících se provozu nebo údržby. POZOR: Toto zařízení může vytvářet nebo používat vysokofrekvenční energii. Změ…

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: Dec 23, 2013 SUBJECT: FCC Application for (FCC ID: PB4-TDKA12) To Whom It May Concern: I, the undersigned, hereby attest to the fact that I will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1. Devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. 3. Pt 2.1077 contains the list of information that must be included in the Declaration of Conformity, which must be supplied with each product sold. The DoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(c)(2), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Signature: Cheryl D.White\Regulatory Engineer .................................................................................... [typed name and title] Imation Corp. 1 Imation Way, Oakdale, MN 55128 USA

Imation Corp. FCC ID: PB4- TDKA12 POWER OF ATTORNEY Dec. 12 , 2013 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Dec. 11 ,2014 This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Imation Corp. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Imation Corp. ....................................................................................

Model No.:A12 EUT – External View Model No.:A12 EUT – External View Model No.:A12 EUT – External View Model No.:A12 EUT – External View

FCC Label Location This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmfulinterference,and (2) this device must accept any interference received,including interference that may cause undesired operation. The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Lo cation on EUT Back View/ proposed FCC Label Location

FCC Label Sample for model: A12 FCC ID: PB4-TDKA12 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. TDK Life on Record

Model No:A12 EUT – Internal View ANT 2.1 EUT – RF Module View

FCC TEST REPORT Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 73 Reference No. .................... : WTS13S1109360E FCC ID ................................ : PB4-TDKA12 Applicant ............................ : Imation Corp. Address .............................. : 1 Imation Way, Oakdale, MN 55128 USA Manufacturer .................... : Imation Corp. Address .............................. : 1 Imation Way, Oakdale, MN 55128 USA Product Name .................... : Wireless Speaker Model No. ........................... : A12 Trademark...................... : TDK Life on Record Standards........................... : FCC CFR47 Part 15 Subpart C: 2012 Date of Receipt sample .... : 2013-11-26 Date of Test ....................... : 2013-11-26 to 2013-12-04 Date of Issue ...................... : 2013-12-23 Test Report Form No. ....... : WEO-FCC15A-05A Test Result ......................... : Pass * *Remarks: The sample described above has been tested to be in compliance with the requirements of ANSI C63.4:2003. The test results have been reviewed and comply with the rules listed above and found to meet their essential requirements. The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Testing location: The same as above Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Tiger Ye / Project Engineer Philo Zhong / Manager Reference No.: WTS13S1109360E Page 2 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 2 Test Summary Test Items Test Requirement Result Spurious Radiated Emissions 15.205(a) 15.209 15.247(d) PASS Band edge Emissions 15.247(d) PASS Spurious RF Conducted Emissions from out of band 15.247(d) PASS Duty Cycle 15.35 PASS Conducted Emissions 15.207 PASS 20dB Bandwidth 15.215c 15.247(a)(1) PASS Maximum Peak Output Power 15.247(b)(1) PASS Frequency Separation 15.247(a)(1) PASS Number of Hopping Frequency 15.247(a)(1)(iii) PASS Dwell time 15.247(a)(1)(iii) PASS Maximum Permissible Exposure (Exposure of Humans to RF Fields) 1.1307(b)(1) PASS Reference No.: WTS13S1109360E Page 3 of 73 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 TEST SUMMARY .................................................................................................................................................. 2 3 CONTENTS ............................................................................................................................................................ 3 4 GENERAL INFORMATION .................................................................................................................................. 5 4.1 GENERAL DESCRIPTION OF E.U.T. ................................................................................................................ 5 4.2 DETAILS OF E.U.T. ......................................................................................................................................... 5 4.3 CHANNEL LIST ................................................................................................................................................. 5 4.4 TEST FACILITY ................................................................................................................................................. 6 4.5 TEST LOCATION ............................................................................................................................................... 6 5 EQUIPMENT USED DURING TEST .................................................................................................................. 7 5.1 EQUIPMENTS LIST ........................................................................................................................................... 7 5.2 MEASUREMENT UNCERTAINTY ....................................................................................................................... 7 5.3 TEST EQUIPMENT CALIBRATION ..................................................................................................................... 7 6 CONDUCTED EMISSION .................................................................................................................................... 8 6.1 E.U.T. OPERATION ......................................................................................................................................... 8 6.2 EUT SETUP ..................................................................................................................................................... 8 6.3 CONDUCTED EMISSION TEST RESULT ........................................................................................................... 9 7 SPURIOUS RADIATED EMISSIONS ............................................................................................................... 11 7.1 EUT OPERATION : ......................................................................................................................................... 11 7.2 TEST SETUP .................................................................................................................................................. 12 7.3 SPECTRUM ANALYZER SETUP ...................................................................................................................... 13 7.4 TEST PROCEDURE ..........................................................................................................................…

Text truncated - open the document above for the full version.

2 Photographs – Test Setup 2.1 Conducted Emissions 2.2 Radiated Emissions Below 30MHz From 30-1000MHz Above 1GHz