PB6-02012WLAN PCMCIA Card

Wireless LAN PC Card User’s Manual Ver 1.3 1 Copyright © 2001 by manufacturer. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from the copyright owner. All the other trademarks and registered trademarks are the property of their respective owners. Statement of Conditions The content described in this manual may be improved or changed at any time and it is subject to be changed without notice. Manufacturer assumes no responsibility for errors contained herein or for direct, indirect, special, incidental or consequential damages with the furnishing, performance, or use of this manual or equipment supplied with it, even if manufacturer of its suppliers have been advised of the possibility of such damages. Electronic Emission Notices This device complies with Part 15 of the FCC Rules and Canada RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device will accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user need to correct the interference at his area. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: ü Plug the equipment into an outlet that is on a different circuit from the television or radio. ü Change the direction of the television or radio antenna until the interference disappears. ü Move the equipment to one side or the other of the television or radio. ü Move the equipment farther away from the television or radio. To assure continued compliance, any changes or modifications not expressly approved by manufacturer could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement This device and its antennas must not be co-located or operating in conjunction with any other antenna or transmitter. End users must be provided with specific operating instructions for satisfying RF exposure compliance. This product has been certified in Canada, France, Germany, Italy, Spain, Sweden, Taiwan, UK, and US. 2 LIMITED WARRANTY This product is warranted by manufacturer to be free from defects in material and workmanship for one (1) year from the date of purchase. During this period if this product is found to be defective in material or workmanship, manufacturer or one of its authorized service facilities will at its option either repair or replace this product without charge, subject to the following conditions, limitations and exclusions: 1. This warranty extends to the original consumer purchaser only and is not assignable or transferable. 2. This warranty shall not apply to any product which has been subjected to misuse, abuse, abnormal use, negligence, alteration or accident, or has had its serial number altered or removed. 3. This warranty does not apply to any defects or damage directly or indirectly caused by or resulting from the use of unauthorized replacement parts and/or service performed by unauthorized personnel. 4. This warranty does not apply to the software driver that accompanies this product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including but not limited to any implied warranty of merchantability of fitness for a particular purpose, and all other obligations on the part of Manufacturer provided, however, that if the disclaimer of implied warranties is ineffective under applicable law, the duration of any implied warranties arising by operation of law shall be limited to one (1) year from the date of purchase or such longer period as may be required by applicable law. Manufacturer hereby disclaims any and all liabilities for consequential and incidental damages arising out of or in connection with any breach of this warranty or any other claim with respect to this product, including but not limited to claims of negligence, strict liability in tort or breach of contract. 3 Table of Contents 1. INTRODUCTION................................................................................................................................4 1.1 Features.....................................................................................................................................4 1.2 Applications................................................................................................................................4 1.3 Wireless LAN System..................................................................................................................4 1.3.1 802.11 Ad-Hoc Configuration..........................................................................................4 1.3.2 Infrastructure Configuration............................................................................................5 2. INSTALLATION..................................................................................................................................8 2.1 Product Kit..................................................................................................................................8 2.2 PC’s Minimum Requirements......................................................................................…

Text truncated - open the document above for the full version.

C100 Block Diagram

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 August 29, 2002 RE: TeLLUS Group FCC ID: PB6-02012 I have a few comments on this Application. 1.) The FCC has adjusted some of it’s interpretations of PCMCIA cards when used in laptop computers. Current thinking requires a TCB to consider the final usage of the device and how it may be operated by typical end users. This device consists of a PCMCIA card with a measured Pout of 24mW connected to either an integral antenna on the nose of the PCMCIA card, or to an external antenna mounted on the nose and connected directly via a reverse threaded SMA connection. My concern is with the external antenna showing a reported gain of +2dBi. The FCC has set a threshold limit of 60mW/f(GHz) radiated or conducted power for all transmitters which are capable of body contact during normal operations. Any approval above this threshold can still be performed by a TCB; however it is required the Applicant supply SAR test data before any Grant of Equipment Authorization is issued. If you need help in locating an appropriate test facility please let us know. I am also attaching for your reference a copy of the new TCB Exclusion List which became effective July 17 of this year. Again, if you have questions on this document I will be happy to assist you. In addition, and until this issue has been resolved, no further processing of your Application will proceed. We must resolve these RF Exposure considerations. Regards, William H. Graff President and Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

External Photo of the TeLLUS C100 External Photo of the TeLLUS C100 External Photo of the TeLLUS C100

Label Location of the TeLLUS C100

Internal Photo of the TeLLUS C100 Internal Photo of the TeLLUS C100 Internal Photo of the TeLLUS C100 Internal Photo of the TeLLUS C100 Internal Photo of the TeLLUS C100 Internal Photo of the TeLLUS C100

Training Research Co., Ltd. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. TEL: 886-2-26935155 FAX: 886-2-26934440 TRCSince1985 ® Measurement of MPE 1. Foreword In adopt with the Human Exposure IEEE C95.1, and according to the FCC 1.1310. The Maximum Permissible Exposure (MPE) is obligated to measure in order to prove the safety of radiation harmfulness to the human body. The Gain of the antenna used is measured in an Anechoic chamber. The maximum total power to the antenna is to be recorded. By adopting the Friis Transmission Formula and the power gain of the antenna, we can find the distance right away from the product, where the limit of the MPE is. 2. Description of EUT EUT : Wireless LAN PC Card Classification : Portable Device (i) Under normal use condition, the antenna is at least 5cm away from the user; (ii) Warning statement for keeping 5cm separation distance and the prohibition of operating next to the person has been printed in the user’s manual Model No. : C100 / C100A Granted FCC ID : PB6-02012 Frequency Range : 2.412 GHz ~ 2.462GHz Antenna Kit : 1 internal printed integral antenna / 1 external dipole antenna (C100 with printed integral antenna; and C100A with external dipole antenna made by Antenniques) Supported Channel: 11 Channel Modulation Skill : DBPSK, DQPSK, CCK Power Type : Powered by the PCMCIA slot of the client device Applicant : TeLLUS Group Corp. 4/F, No.15, Industry E. Rd. IX, Science-based Industrial Park, Hsinchu 300, Taiwan, R.O.C. Training Research Co., Ltd. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. TEL: 886-2-26935155 FAX: 886-2-26934440 TRCSince1985 ® 3. Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Filed Strength (H) (A/m) Power Density (S) (mW/cm2) Averaging Time |E| 2 , |H| 2 or S (minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 100 6 3.0-30 1842/f 4.89/f 900/f 2 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- f/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 100 30 1.34-30 824/f 2.19/f 180/f 2 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- f/1500 30 1500-100,000 -- -- 1.0 30 [The EUT is tested in transmit and receive modes and in the first, middle and the last channel separately. The following shows only our observation have the greatest emissions.] According to OET BULLETIN 56 Fourth Edition/August 1999, equation for predicting RF fields, by the Friis Transmission Formula: Power density at the specific separation (portable): 22 22 /10806.6 )5(4 585.149.13 4 cmmW R PG S − ×= × == ππ Estimated safe separation: cm PG R304.1 4 585.149.13 4 = × == ππ Remarks: "The safe estimated separation that the user must maintain from the antenna is at least 1.304 cm." Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) The Numeric gain G of antenna with a gain specified in dB is determined by: G = Log -1 (dB antenna gain/10) G = Log -1 (2 / 10) = 1.585

Test Report -------------------------------------------------------------------------------- 1/50 Report No.: T6915617 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 MEASUREMENT REPORT of WIRELESS LAN PC CARD Applicant : TeLLUS GROUP CORPORATION Model No. : C100 / C100A EUT : TeLLUS WLAN PC Card FCC ID : PB6-02012 Report No. : T6915617 Tested by : Training Research Co., Ltd. TEL : 886-2-26935155 FAX : 886-2-26934440 255 Nanyang St., Shijr, Taipei Hsien 221, Taiwan, R.O.C. Test Report -------------------------------------------------------------------------------- 3/50 Report No.: T6915617 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Tables of Contents I. GENERAL ......................................................................................................................... 5 1.1 Introduction .................................................................................................................. 5 1.2 Description of EUT ....................................................................................................... 5 1.3 Description of Support Equipment ................................................................................. 6 1.4 Configuration of System Under Test .............................................................................. 8 1.5 Verify the Frequency and Channel ................................................................................. 9 1.6 Test Procedure ............................................................................................................ 10 1.7 Location of the Test Site ............................................................................................... 10 1.8 General Test Condition ................................................................................................. 10 II. Section 15.203 : Antenna Requirement............................................................................. 11 III. Section 15.207: Power Line Conducted Emissions for AC Powered Units .................... 12 3.1 Test Condition & Setup ................................................................................................ 12 3.2 List of Test Instruments ................................................................................................ 12 3.3 Test Configuration ........................................................................................................ 13 3.4 Test Result of Conducted Emissions ............................................................................. 14 IV. Section 15.247(a) : Technical Description of the EUT..................................................... 18 V. Section 15.247(a)(2): Bandwidth for Direct Sequence System ...................................... 19 5.1 Test Condition & Setup ................................................................................................ 19 5.2 Test Instruments Configuration ...................................................................................... 19 5.3 List of Test Instruments ................................................................................................ 19 5.4 Test Result of Bandwidth .............................................................................................. 20 VI. Section 15.247(b) : Power Output .................................................................................... 24 6.1 Test Condition & Setup ................................................................................................ 24 6.2 List of Test Instruments ................................................................................................ 25 6.3 Test Result ................................................................................................................... 25 VII. Section 15.247(c) : Spurious Emissions (Radiated) ........................................................ 26 7.1 Test Condition & Setup ................................................................................................ 26 7.2 List of Test Instruments ................................................................................................ 27 7.3 Test Instruments Configuration ...................................................................................... 28 7.4 Test Result of Spurious Radiated Emissions .................................................................. 29 7.5 Test Result of Bandedge................................................................................................. 42 VIII.Section 15.247(d) : Power Spectral Density ................................................................... 45 8.1 Test Condition & Setup ................................................................................................ 45 8.2 Test Instruments Configuration ...................................................................................... 45 8.3 List of Test Instruments.................................................................................................. 45 8.4 Test Result of Power Spectral Density .......................................................................... 46 Test Report -------------------------------------------------------------------------------- 4/50 Report No.: T6915617 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Appendix A: Set Up Procedure ............................................................................................... 50 Test Report -------------------------------------------------------------------------------- 5/50 Report No.: T6915617 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 GENERAL 1.1 Introduction The following measurement report is submitted on behalf of Applicant in support of a wireless LAN PC Card certification in accordance with Part 2 Subpart J and Part 15 Subpart A and C of the Commission's Rules and Regulations. 1.2 Description of EUT EUT : TeLLUS WLAN LAN PC Card Model…

Text truncated - open the document above for the full version.

Test Report -------------------------------------------------------------------------------- 24/50 Report No.: T6915617 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 VI. Section 15.247(b): Power Output 6.1 Test Condition & Setup 1. The output of the transmitter is connected to the BOONTON RF Power Meter. 2. The calibration is performed before every test. The values of the output power of the EUT will shown in the dBm directly are the transmitter output peak power. Recording as follows. EUT BOONTON 4532 RF Power Meter Test Report -------------------------------------------------------------------------------- 25/50 Report No.: T6915617 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 6.2 List of Test Instruments Instrument Name Model No. Brand Serial No. RF Power Meter 4532 BOONTON 117501 6.3 Test Result Formula: Signal generator + |Cable loss| = Output peak power Power Meter Reading Cable Loss Limit Output peak power Channel dBm dBm (DSS) dBm mW CH1 6.12 5.18 100mW 11.30 13.49 CH6 5.20 5.20 100mW 10.40 10.96 CH11 3.92 5.25 100mW 9.17 8.26 Note: The limit is vary according to the equipment class, listed below: 1. Digital Transmission System (DTS): 100mW 2. Spread Spectrum Transmitter (DSS): 1W

Training Research Co., Ltd. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. TEL: 886-2-26935155 FAX: 886-2-26934440 TRCSince1985 ® Test setup photos: TeLLUS Wireless LAN PC Card (Test report no.: T6915617) FCC ID: PB6-02012 Test Instruments Configuration of Conducted Emissions Training Research Co., Ltd. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. TEL: 886-2-26935155 FAX: 886-2-26934440 TRCSince1985 ® Test Instruments Configuration of Bandwidth Test Configuration of Bandwidth for Direct Sequence System P.S.: Notebook computer to control the EUT at maximal power output and channel Number and set antenna kit Test Condition & Setup of Power Output EUT Spectrum Analyzer (RBW:100kHz; VBW: 100kHz) EUT BOONTON 4532 RF Power Meter Training Research Co., Ltd. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. TEL: 886-2-26935155 FAX: 886-2-26934440 TRCSince1985 ® Test Instruments Configuration of the Spurious Radiated Emissions Front View of the Test Configuration Rear View of the Test Configuration The test configuration for frequency between 1GHz to 18GHz is same as above. Training Research Co., Ltd. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. TEL: 886-2-26935155 FAX: 886-2-26934440 TRCSince1985 ® Test Instruments Configuration of Power Spectral Density Test Configuration of Power Spectral Density P.S.: Notebook computer to control the EUT at maximal power output and channel number and set antenna kit EUT Spectrum Analyzer (RBW:3kHz; VBW: 10kHz)