PHX-MMDS-BASE1Broadband Wireless Access Base Station

Configuring, Installing, and Operating Base Stations MMDS Broadband Wireless Access System Date: April 4, 2001 Part Number:104-0100-0001-A Expedience is a trademark of NextNet Wireless. ©2000-2001 NextNet Wireless, Inc. All rights reserved. NOTICE: This equipment has been tested with a 20 dB gain antenna and found to comply with the Radio Frequency Radiation Exposure Limits detailed below. A minimum of 1-meter separation between the installation/operator technician and the transmitting antenna should be maintained. Radio Frequency Radiation Exposure Limits. f = frequency in MHz * = Plane-wave equivalent power density NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy, and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRENTY OF ANY KIND. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCT. TABLE 1. Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field- strength (V/m) Magnetic field- strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.06141.63*(100)6 3.0-301842/f4.89/f *(900/f 2 ) 6 30-30061.40.1631.06 300-1500——f/3006 1500-100,000——56 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.346141.63*(100)30 1.34-30824/f2.19/f *(180/f 2 ) 30 30-30027.50.073.230 300-1500——f/150030 1500-100,000——1.030 NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED "AS IS" WITH ALL FAULTS. NEXTNET WIRELESS DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FOM A COUSRE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL NEXTNET WIRELESS OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OF DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF NEXTNET WIRELESS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. i CHAPTER 0CONTENTS PrefaceAbout this guide Preface Overview ............................................................................... ix About this guide ................................................................................ ix Chapters in this guide ........................................................................................... x Additional documentation ................................................................. xi How to obtain additional documentation ........................................................ xi Typographical conventions this guide uses ..................................... xii Where to go for more help ............................................................... xiii Technical support............................................................................................... xiii Documentation additions and corrections ..................................................... xiii Chapter 1Introduction to base station installations Chapter overview .............................................................................. 1-1 System overview ................................................................................ 1-1 Base station overview ....................................................................................... 1-2 Installation overview .........................................................................1-3 Planning the installation ...................................................................1-4 Choosing an installation location .................................................................... 1-4 Assessing service provider equipment needs ................................................ 1-6 Planning for the antennas and antenna installation tips .............................. 1-6 Chapter 2Configuring base stations Chapter overview ............................................................................. 2-7 Before you begin .............................................................................. 2-7 Using Term or Telnet to help configure base stations ................... 2-8 Connecting through Telnet ............................................................................. 2-8 Connecting through terminal emulation ....................................................... 2-9 iiConfiguring, Installing, and Using Base Stations Terminal emulation conne…

Text truncated - open the document above for the full version.

Configuring, Installing, and Operating Base Stations MMDS Broadband Wireless Access System Date: April 18, 2001 Part Number:104-0100-0001-A Expedience is a trademark of NextNet Wireless. ©2000-2001 NextNet Wireless, Inc. All rights reserved. WARNING: This equipment has been tested with a 20 dB gain antenna and found to comply with the FCC guidelines for Radio Frequency Radiation Exposure Limits as detailed below. A minimum of 1-meter separation between the antenna and the installation/operator technician and the general public must be maintained. Radio Frequency Radiation Exposure Limits. f = frequency in MHz * = Plane-wave equivalent power density NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy, and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRENTY OF ANY KIND. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCT. TABLE 1. Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field- strength (V/m) Magnetic field- strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.06141.63*(100)6 3.0-301842/f4.89/f *(900/f 2 ) 6 30-30061.40.1631.06 300-1500——f/3006 1500-100,000——56 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.346141.63*(100)30 1.34-30824/f2.19/f *(180/f 2 ) 30 30-30027.50.073.230 300-1500——f/150030 1500-100,000——1.030 NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED "AS IS" WITH ALL FAULTS. NEXTNET WIRELESS DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FOM A COUSRE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL NEXTNET WIRELESS OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OF DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF NEXTNET WIRELESS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NextNet Wireless, Inc. recommends the following antennas for base station installations: ManufacturerAntenna typeModel/part number Thales60 degree vertical polarization 2600-VP-65-19 Andrew Antenna60 degree vertical polarization Datamaster DMP20W060-V i CHAPTER 0CONTENTS PrefaceAbout this guide Preface Overview ............................................................................... ix About this guide ................................................................................ ix Chapters in this guide ........................................................................................... x Additional documentation ................................................................. xi How to obtain additional documentation ........................................................ xi Typographical conventions this guide uses ..................................... xii Where to go for more help ............................................................... xiii Technical support............................................................................................... xiii Documentation additions and corrections ..................................................... xiii Chapter 1Introduction to base station installations Chapter overview .............................................................................. 1-1 System overview ................................................................................ 1-1 Base station overview ....................................................................................... 1-2 Installation overview .........................................................................1-3 Planning the installation ...................................................................1-4 Choosing an installation location .................................................................... 1-4 Assessing service provider equipment needs ................................................ 1-6 Planning for the antennas and antenna installation tips .............................. 1-6 Chapter 2Configuring base stations Chapter overview ............................................................................. 2-7 Before you begin .............................................................................. 2-7 Using Terminal Emulation or Telnet to help configure base stations .......…

Text truncated - open the document above for the full version.

NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 1 of 5 Bloomington, MN 55431 Exhibit 13 Request for Confidentiality 4/9/2001 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: PHX-MMDS-BASE1 Please be advised that the following information is to be held confidential and behalf of NextNet Wireless, Inc.: • Exhibit 4 - Block Diagrams • Exhibit 5 - Schematics • Exhibit 12 - Technical Description The application contains technical information which NextNet Wireless, Inc. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 2 of 5 Bloomington, MN 55431 Exhibit 13 Modification Letter 4/9/2001 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: PHX-MMDS-BASE1 Please be advised that the following information is a list of modifications that will be included in the production process for the above-referenced equipment. No modifications were performed during the measurement of this product for FCC compliance. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 3 of 5 Bloomington, MN 55431 Exhibit 13 Warning Statements and Locations The following warning statement is located on page two of the “Configuring, Installing, and Operating Base Stations” manual. NOTICE: This equipment has been tested with a 20 dB gain antenna and found to comply with the Radio Frequency Radiation Exposure Limits detailed below. A minimum of 1-meter separation between the installation/operator technician and the transmitting antenna should be maintained. NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 4 of 5 Bloomington, MN 55431 Exhibit 13 Manufacturer’s Letter 4/9/2001 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: PHX-MMDS-BASE1 To Whom It May Concern: Please be advised that the manufacturer will ensure that the above-referenced model will be manufactured in accordance with the FCC Rules and Regulations. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 5 of 5 Bloomington, MN 55431 Exhibit 13 Letter Of Agency 4/9/2001 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: NextNet Wireless, Inc. will act on its own behalf for applications submitted to American Telecommunications Certification Body, Inc. (ATCB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc.

NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 1 of 3 Bloomington, MN 55431 Response to American Telecommunications Certification Body Inc. questions dated April 17, 2001 1. Internal photographs: Solder side photograph of RF board included in Exhibit 9a. 2. Parts List: Updated Request for Confidentiality included in Exhibit 13a. 3. TX Radiated Spurious RBW included in test procedure in Exhibit 6a. 4. Emission Designator justification added to Exhibit 12a. New Form 731 submitted. Measured bandwidth in shown in Exhibit 6 and Exhibit 6a under the Occupied Bandwidth measurements. 5. Manual updated to include base site antennas. New manual included in Exhibit 8a. 6. RF Exposure Warning statement in manual has been updated. New manual is included in Exhibit 8a. The Warning statement is also detailed in Warning Statements and Locations section of Exhibit 13a. 7. Grant note. Acknowledged. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 2 of 3 Bloomington, MN 55431 Exhibit 13a Request for Confidentiality 4/9/2001 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: PHX-MMDS-BASE1 Please be advised that the following information is to be held confidential and behalf of NextNet Wireless, Inc.: • Exhibit 4 - Block Diagrams • Exhibit 5 – Schematics • Exhibit 10 – Parts List • Exhibit 12 - Technical Description • Exhibit 12a- Technical Description The application contains technical information which NextNet Wireless, Inc. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-BASE1 9555 James Ave. South Suite 270 Page 3 of 3 Bloomington, MN 55431 Exhibit 13a Warning Statements and Locations The following warning statement is located on page two of the “Configuring, Installing, and Operating Base Stations” manual. WARNING: This equipment has been tested with a 20 dB gain antenna and found to comply with the FCC guidelines for Radio Frequency Radiation Exposure Limits as detailed below. A minimum of 1-meter separation between the antenna and the installation / operator technician and the general public must be maintained.

FCC ID: PHX-MMDS-BASE1 Page 1 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Attestation Statement The measurements performed on the test sample for this FCC product Certification were performed by me or by personnel under my direction. Tim Blom Principal Engineer FCC ID: PHX-MMDS-BASE1 Page 2 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Cover Letters Gentlemen: This report is being submitted to the Federal Communications Commission for the Certification of equipment pursuant to 2000 Title 47 CFR parts 1, 2, 21, and 74 dated 10- 1-00 Edition. FCC Rule Part Description Response 0.457dii Records not routinely available for public inspection See exhibit 13 0.459 Requests that materials or information submitted to the Commission be withheld from public inspection. See exhibit 13 2.1033(c)1 The full name and mailing address of the manufacturer of the device and the applicant for certification. NextNet Wireless, Inc. 9555 James Avenue South, Suite 270 Bloomington, MN 55431 2.1033(c)2 FCC identifier. PHX-MMDS-BASE1 2.1033(c)3 A copy of the installation and operating instructions. See information located within exhibit 8 2.1033(c)4 Type or types of emission. 21.905(b): OFDM / 6M0D1D 74.936(a): OFDM / 6M0D1D 2.1033(c)5 Frequency range. 2500 – 2686 MHz 2.1033(c)6 Range of operating power values or specific operating power levels, and description of any means provided for variation of operating power. 0.001 Watts – 2 Watts Power is adjustable by system operator via computer interface. 2.1033(c)7 Maximum power rating as defined in the applicable part(s) of the rules. 21.904(b): 39 dBW EIRP 74.935(b): 39 dBW EIRP 2.1033(c)8 The dc voltages applied to and dc currents into the several elements of the final radio frequency amplifying device for normal operation over the power range. See block diagram in exhibit 4 2.1033(c)9 Tune-up procedure over the power range, or at specific operating power levels. See tune-up information in exhibit 12 2.1033(c)10 A schematic diagram and a description of all circuitry and devices provided for determining and stabilizing frequency, for suppression of spurious radiation, for limiting modulation, and for limiting power. See schematics in exhibit 5. See circuit descriptions in exhibit 12. 2.1033(c)11 A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. See exhibit 1 FCC ID: PHX-MMDS-BASE1 Page 3 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 2.1033(c)12 Photographs (8”x10”) of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. Insofar as these requirements are met by photographs or drawings contained in instruction manuals supplied with the certification request, additional photographs are necessary only to complete the required showing. See photographs in Exhibit 9 2.1033(c)13 For equipment employing digital modulation techniques, a detailed description of the modulation system to be used, including the response characteristics (frequency, phase and amplitude) of any filters provided, and a description of the modulating wavetrain, shall be submitted for the maximum rated conditions under which the equipment will be operated. See Exhibit 12 2.1033(c)14 The data required by §§ 2.1046 through 2.1057, inclusive, measured in accordance with the procedures set out in § 2.1041 See Test Report measurements in Exhibit 6 2.1033(c)15 The application for certification of an external radio frequency power amplifier under part 97 of this chapter need not be accompanied by the data required by paragraph (b)(14) of this section. In lieu thereof, measurements shall be submitted to show compliance with the technical specifications in subpart C of part 97 of this chapter and such information as required by § 2.1060 of this part. Not applicable 2.1033(c)16 An application for certification of an AM broadcast stereophonic exciter-generator intended for interfacing with existing certified, or formerly type accepted or notified transmitters must include measurements made on a complete stereophonic transmitter. The instruction book must include complete specifications and circuit requirements for interconnecting with existing transmitters. The instruction book must also provide a full description of the equipment and Not applicable FCC ID: PHX-MMDS-BASE1 Page 4 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 measurement procedures to monitor modulation and to verify that the combination of stereo exciter-generator and transmitter meet the emission limitations of § 73.44. 2.1033(c)17 A single application may be filed for a composite system that incorporates devices subject to certification under multiple rule parts, however, the appropriate fee must be included for each device. Not applicable FCC ID: PHX-MMDS-BASE1 Page 5 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Cover Letters Test Report Summary CFR Rule Part Requirement Test Result 2.1046 RF Output Power Pass 2.1047 Modulation Characteristics Pass 2.1049 Occupied Bandwidth Pass 2.1051 Spurious Emissions at Antenna Terminals Pass 2.1053 Field Strength of Spurious Radiation Pass 2.1055 Frequency Stability Pass 1.1310 Radio Frequency Radiation Exposure Limits Pass Exhibit Summary Exhibit Section Contents 1 FCC ID Label / Location Information 2 Attestation Statement and Cover Letters 3 External Photographs 4 Block Diagrams 5 Schematics 6 Test Report 7 Test Setup Photographs 8 Installation and Operating Manual 9 Internal Photographs 10 Parts List 11 RF Exposure Information 12 Operational Description 13 Correspondence

FCC ID: PHX-MMDS-BASE1 Page 1 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2a Attestation Statement The measurements performed on the test sample for this FCC product Certification were performed by me or by personnel under my direction. Tim Blom Principal Engineer FCC ID: PHX-MMDS-BASE1 Page 2 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2a Cover Letters Gentlemen: This report is being submitted to the Federal Communications Commission for the Certification of equipment pursuant to 2000 Title 47 CFR parts 1, 2, 21, and 74 dated 10- 1-00 Edition. FCC Rule Part Description Response 0.457dii Records not routinely available for public inspection See exhibit 13 0.459 Requests that materials or information submitted to the Commission be withheld from public inspection. See exhibit 13 2.1033(c)1 The full name and mailing address of the manufacturer of the device and the applicant for certification. NextNet Wireless, Inc. 9555 James Avenue South, Suite 270 Bloomington, MN 55431 2.1033(c)2 FCC identifier. PHX-MMDS-BASE1 2.1033(c)3 A copy of the installation and operating instructions. See information located within exhibit 8 2.1033(c)4 Type or types of emission. 21.905(b): OFDM / 5M8XXD 74.936(a): OFDM / 5M8XXD 2.1033(c)5 Frequency range. 2500 – 2686 MHz 2.1033(c)6 Range of operating power values or specific operating power levels, and description of any means provided for variation of operating power. 0.001 Watts – 2 Watts Power is adjustable by system operator via computer interface. 2.1033(c)7 Maximum power rating as defined in the applicable part(s) of the rules. 21.904(b): 39 dBW EIRP 74.935(b): 39 dBW EIRP 2.1033(c)8 The dc voltages applied to and dc currents into the several elements of the final radio frequency amplifying device for normal operation over the power range. See block diagram in exhibit 4 2.1033(c)9 Tune-up procedure over the power range, or at specific operating power levels. See tune-up information in exhibit 12 2.1033(c)10 A schematic diagram and a description of all circuitry and devices provided for determining and stabilizing frequency, for suppression of spurious radiation, for limiting modulation, and for limiting power. See schematics in exhibit 5. See circuit descriptions in exhibit 12. 2.1033(c)11 A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. See exhibit 1 FCC ID: PHX-MMDS-BASE1 Page 3 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 2.1033(c)12 Photographs (8”x10”) of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. Insofar as these requirements are met by photographs or drawings contained in instruction manuals supplied with the certification request, additional photographs are necessary only to complete the required showing. See photographs in Exhibit 9 2.1033(c)13 For equipment employing digital modulation techniques, a detailed description of the modulation system to be used, including the response characteristics (frequency, phase and amplitude) of any filters provided, and a description of the modulating wavetrain, shall be submitted for the maximum rated conditions under which the equipment will be operated. See Exhibit 12 2.1033(c)14 The data required by §§ 2.1046 through 2.1057, inclusive, measured in accordance with the procedures set out in § 2.1041 See Test Report measurements in Exhibit 6 2.1033(c)15 The application for certification of an external radio frequency power amplifier under part 97 of this chapter need not be accompanied by the data required by paragraph (b)(14) of this section. In lieu thereof, measurements shall be submitted to show compliance with the technical specifications in subpart C of part 97 of this chapter and such information as required by § 2.1060 of this part. Not applicable 2.1033(c)16 An application for certification of an AM broadcast stereophonic exciter-generator intended for interfacing with existing certified, or formerly type accepted or notified transmitters must include measurements made on a complete stereophonic transmitter. The instruction book must include complete specifications and circuit requirements for interconnecting with existing transmitters. The instruction book must also provide a full description of the equipment and Not applicable FCC ID: PHX-MMDS-BASE1 Page 4 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 measurement procedures to monitor modulation and to verify that the combination of stereo exciter-generator and transmitter meet the emission limitations of § 73.44. 2.1033(c)17 A single application may be filed for a composite system that incorporates devices subject to certification under multiple rule parts, however, the appropriate fee must be included for each device. Not applicable FCC ID: PHX-MMDS-BASE1 Page 5 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2a Cover Letters Test Report Summary CFR Rule Part Requirement Test Result 2.1046 RF Output Power Pass 2.1047 Modulation Characteristics Pass 2.1049 Occupied Bandwidth Pass 2.1051 Spurious Emissions at Antenna Terminals Pass 2.1053 Field Strength of Spurious Radiation Pass 2.1055 Frequency Stability Pass 1.1310 Radio Frequency Radiation Exposure Limits Pass Exhibit Summary Exhibit Section Contents 1 FCC ID Label / Location Information 2 Attestation Statement and Cover Letters 3 External Photographs 4 Block Diagrams 5 Schematics 6 Test Report 7 Test Setup Photographs 8 Installation and Operating Manual 9 Internal Photographs 10 Parts List 11 RF Exposure Information 12 Operational Description 13 Correspondence Exhibit Section Contents 2a Attestation Statement and Cover Letters update …

Text truncated - open the document above for the full version.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 April 17, 2001 RE: FCC ID: PHX-MMDS-BASE1 Attention: Tim Blom I have a couple of comments about this Application which need to be addressed. 1.) Internal Photographs: There is no …

Text truncated - open the document above for the full version.