PHX-MMDS-CPE1Non-Line of Site Wireless Data Link

i Installing and using your CPE device Directions for connecting your CPE to a computer or LAN and obtaining high- speed Internet and voice services. ii Expedience is a trademark of NextNet Wireless. ©2000-2001 NextNet Wireless, Inc. All rights reserved. NOTICE: This equipment has been tested and found to comply with the Radio Frequency Radiation Exposure Limits detailed below. A minimum of 20 centimeters (8 inches) separation between the CPE and the operator and all other persons should be maintained. Radio Frequency Radiation Exposure Limits f = frequency in MHz * = Plane-wave equivalent power density NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy, and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRENTY OF ANY KIND. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCT. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED “AS IS” WITH ALL FAULTS. NEXTNET WIRELESS DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR TABLE 1. Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.06141.63*(100)6 3.0-301842/f4.89/f *(900/f 2 ) 6 30-30061.40.1631.06 300-1500——f/3006 1500-100,000——56 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.346141.63*(100)30 1.34-30824/f2.19/f *(180/f 2 ) 30 30-30027.50.073.230 300-1500——f/150030 1500-100,000——1.030 iii ARISING FOM A COUSRE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL NEXTNET WIRELESS OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OF DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF NEXTNET WIRELESS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. iv Contents Welcome! ....................................................................................... 1 Before You Begin ....................................................................... 1 Connecting your CPE to a computer or LAN ......................................... 4 Installation Overview .................................................................. 4 Setting up the computer to dynamically receive an IP address ......... 4 Windows 95, Windows 98, Windows NT: Setting up the network connection ................................................................................ 5 Windows 2000: Setting up the network connection ......................... 5 Connecting the CPE to a Computer or Network ............................... 6 Connecting the CPE to a computer ............................................... 6 Connecting the CPE to a network ................................................. 7 Supplying Power to the CPE ........................................................ 8 Finding the Strongest Service Provider Signal ................................ 8 Using the Software-Assisted Method to Find the Strongest Signal ..... 9 Using the LEDs to find the Strongest Service Provider Signal ..........12 Troubleshooting.............................................................................. 18 LEDs that don’t blink, but rather chase ........................................18 The LEDs on the CPE blink more slowly than normal ......................19 You receive a dialog box indicating that you cannot connect to your service provider ........................................................................19 I can successfully contact my service provider at home, but not at work or at a friend’s house .........................................................20 If You have Problems Getting Connected ......................................20 Congratulations! ............................................................................. 21 vi 1 Welcome! This document describes how to install and use your customer premise equipment (CPE), which provides you with high speed internet services.You can connect your CPE to your computer, or you can connect it to a small office/home office (SOHO) local area network (LAN) through a hub, switch, gateway, or router. BEFORE YOU BEGIN •Make sure your computer is equipped with an Ether- net network interface card (NIC). •…

Text truncated - open the document above for the full version.

NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 1 of 5 Bloomington, MN 55431 Exhibit 13 Request for Confidentiality 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: Certification Application FCC ID: PHX-MMDS-CPE1 Please be advised that the following information is to be held confidential and behalf of NextNet Wireless, Inc.: • Exhibit 4 - Block Diagrams • Exhibit 5 – Schematics • Exhibit 10 – Parts list • Exhibit 12 - Technical Description The application contains technical information which NextNet Wireless, Inc. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 2 of 5 Bloomington, MN 55431 Exhibit 13 Modification Letter 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: Certification Application FCC ID: PHX-MMDS-CPE1 Please be advised that the following information is a list of modifications that will be included in the production process for the above-referenced equipment. No modifications were performed during the measurement of this product for FCC compliance. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 3 of 5 Bloomington, MN 55431 Exhibit 13 Warning Statements and Locations The following warning statement is located on page two of the “Installing and using your CPE device” manual. NOTICE: This equipment has been tested and found to comply with the Radio Frequency Radiation Exposure Limits detailed below. A minimum of 20 centimeter (8 inches) separation between the CPE and the operator and all other persons should be maintained. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 4 of 5 Bloomington, MN 55431 Exhibit 13 Manufacturer’s Letter 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: Certification Application FCC ID: PHX-MMDS-CPE1 To Whom It May Concern: Please be advised that the manufacturer will ensure that the above-referenced model will be manufactured in accordance with the FCC Rules and Regulations. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 5 of 5 Bloomington, MN 55431 Exhibit 13 Letter Of Agency 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 To Whom It May Concern: Please be advised that NextNet Wireless, Inc. authorizes American Telecommunications Certification Body, Inc. to act on our behalf for this certification application being submitted to the Federal Communications Commission (FCC). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc.

FCC ID: PHX-MMDS-CPE1 Page 1 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Attestation Statement The measurements performed on the test sample for this FCC product Certification were performed by me or by personnel under my direction. Tim Blom Principal Engineer FCC ID: PHX-MMDS-CPE1 Page 2 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Cover Letters Gentlemen: This report is being submitted to the Federal Communications Commission for the Certification of equipment pursuant to 2000 Title 47 CFR parts 1, 2, 21, and 74 dated 10- 1-00 Edition. FCC Rule Part Description Response 0.457dii Records not routinely available for public inspection See exhibit 13 0.459 Requests that materials or information submitted to the Commission be withheld from public inspection. See exhibit 13 2.1033(c)1 The full name and mailing address of the manufacturer of the device and the applicant for certification. NextNet Wireless, Inc. 9555 James Avenue South, Suite 270 Bloomington, MN 55431 2.1033(c)2 FCC identifier. PHX-MMDS-CPE1 2.1033(c)3 A copy of the installation and operating instructions. See information located within exhibit 8 2.1033(c)4 Type or types of emission. 21.905(b): OFDM / 5M8XXD 74.936(a): OFDM / 5M8XXD 2.1033(c)5 Frequency range. 2500 – 2686 MHz 2.1033(c)6 Range of operating power values or specific operating power levels, and description of any means provided for variation of operating power. 0.001 Watts – 2 Watts Power is adjusted by system based on signal level received at the base station site. 2.1033(c)7 Maximum power rating as defined in the applicable part(s) of the rules. 21.904(b): 39 dBW EIRP 74.935(b): 39 dBW EIRP 2.1033(c)8 The dc voltages applied to and dc currents into the several elements of the final radio frequency amplifying device for normal operation over the power range. See block diagram in exhibit 4 2.1033(c)9 Tune-up procedure over the power range, or at specific operating power levels. See tune-up information in exhibit 12 2.1033(c)10 A schematic diagram and a description of all circuitry and devices provided for determining and stabilizing frequency, for suppression of spurious radiation, for limiting modulation, and for limiting power. See schematics in exhibit 5. See circuit descriptions in exhibit 12. 2.1033(c)11 A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. See exhibit 1 FCC ID: PHX-MMDS-CPE1 Page 3 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 2.1033(c)12 Photographs (8”x10”) of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. Insofar as these requirements are met by photographs or drawings contained in instruction manuals supplied with the certification request, additional photographs are necessary only to complete the required showing. See photographs in Exhibit 9 2.1033(c)13 For equipment employing digital modulation techniques, a detailed description of the modulation system to be used, including the response characteristics (frequency, phase and amplitude) of any filters provided, and a description of the modulating wavetrain, shall be submitted for the maximum rated conditions under which the equipment will be operated. See Exhibit 12 2.1033(c)14 The data required by §§ 2.1046 through 2.1057, inclusive, measured in accordance with the procedures set out in § 2.1041 See Test Report measurements in Exhibit 6 2.1033(c)15 The application for certification of an external radio frequency power amplifier under part 97 of this chapter need not be accompanied by the data required by paragraph (b)(14) of this section. In lieu thereof, measurements shall be submitted to show compliance with the technical specifications in subpart C of part 97 of this chapter and such information as required by § 2.1060 of this part. Not applicable 2.1033(c)16 An application for certification of an AM broadcast stereophonic exciter-generator intended for interfacing with existing certified, or formerly type accepted or notified transmitters must include measurements made on a complete stereophonic transmitter. The instruction book must include complete specifications and circuit requirements for interconnecting with existing transmitters. The instruction book must also provide a full description of the equipment and Not applicable FCC ID: PHX-MMDS-CPE1 Page 4 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 measurement procedures to monitor modulation and to verify that the combination of stereo exciter-generator and transmitter meet the emission limitations of § 73.44. 2.1033(c)17 A single application may be filed for a composite system that incorporates devices subject to certification under multiple rule parts, however, the appropriate fee must be included for each device. Not applicable FCC ID: PHX-MMDS-CPE1 Page 5 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Cover Letters Test Report Summary CFR Rule Part Requirement Test Result 2.1046 RF Output Power Pass 2.1047 Modulation Characteristics Pass 2.1049 Occupied Bandwidth Pass 2.1051 Spurious Emissions at Antenna Terminals Pass 2.1053 Field Strength of Spurious Radiation Pass 2.1055 Frequency Stability Pass 1.1310 Radio Frequency Radiation Exposure Limits Pass 2.1091 Radio Frequency radiation exposure evaluation: mobile devices. Pass Exhibit Summary Exhibit Section Contents 1 FCC ID Label / Location Information 2 Attestation Statement and Cover Letters 3 External Photographs 4 Block Diagrams 5 Schematics 6 Test Report 7 Test Setup Photographs 8 Installation and Operating Manual 9 Internal Photographs 10 Parts List 11 RF Exposure Information 12 Operational Description 13 Co…

Text truncated - open the document above for the full version.

NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 1 of 5 Bloomington, MN 55431 Exhibit 13 Request for Confidentiality 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: Certification Application FCC ID: PHX-MMDS-CPE1 Please be advised that the following information is to be held confidential and behalf of NextNet Wireless, Inc.: • Exhibit 4 - Block Diagrams • Exhibit 5 – Schematics • Exhibit 10 – Parts list • Exhibit 12 - Technical Description The application contains technical information which NextNet Wireless, Inc. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 2 of 5 Bloomington, MN 55431 Exhibit 13 Modification Letter 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: Certification Application FCC ID: PHX-MMDS-CPE1 Please be advised that the following information is a list of modifications that will be included in the production process for the above-referenced equipment. No modifications were performed during the measurement of this product for FCC compliance. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 3 of 5 Bloomington, MN 55431 Exhibit 13 Warning Statements and Locations The following warning statement is located on page two of the “Installing and using your CPE device” manual. NOTICE: This equipment has been tested and found to comply with the Radio Frequency Radiation Exposure Limits detailed below. A minimum of 20 centimeter (8 inches) separation between the CPE and the operator and all other persons should be maintained. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 4 of 5 Bloomington, MN 55431 Exhibit 13 Manufacturer’s Letter 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: Certification Application FCC ID: PHX-MMDS-CPE1 To Whom It May Concern: Please be advised that the manufacturer will ensure that the above-referenced model will be manufactured in accordance with the FCC Rules and Regulations. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc. NextNet Wireless, Inc FCC ID: PHX-MMDS-CPE1 9555 James Ave. South Suite 270 Page 5 of 5 Bloomington, MN 55431 Exhibit 13 Letter Of Agency 4/19/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 To Whom It May Concern: Please be advised that NextNet Wireless, Inc. authorizes American Telecommunications Certification Body, Inc. to act on our behalf for this certification application being submitted to the Federal Communications Commission (FCC). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Tim Blom NextNet Wireless, Inc.

FCC ID: PHX-MMDS-CPE1 Page 1 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Attestation Statement The measurements performed on the test sample for this FCC product Certification were performed by me or by personnel under my direction. Tim Blom Principal Engineer FCC ID: PHX-MMDS-CPE1 Page 2 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Cover Letters Gentlemen: This report is being submitted to the Federal Communications Commission for the Certification of equipment pursuant to 2000 Title 47 CFR parts 1, 2, 21, and 74 dated 10- 1-00 Edition. FCC Rule Part Description Response 0.457dii Records not routinely available for public inspection See exhibit 13 0.459 Requests that materials or information submitted to the Commission be withheld from public inspection. See exhibit 13 2.1033(c)1 The full name and mailing address of the manufacturer of the device and the applicant for certification. NextNet Wireless, Inc. 9555 James Avenue South, Suite 270 Bloomington, MN 55431 2.1033(c)2 FCC identifier. PHX-MMDS-CPE1 2.1033(c)3 A copy of the installation and operating instructions. See information located within exhibit 8 2.1033(c)4 Type or types of emission. 21.905(b): OFDM / 5M8XXD 74.936(a): OFDM / 5M8XXD 2.1033(c)5 Frequency range. 2500 – 2686 MHz 2.1033(c)6 Range of operating power values or specific operating power levels, and description of any means provided for variation of operating power. 0.001 Watts – 2 Watts Power is adjusted by system based on signal level received at the base station site. 2.1033(c)7 Maximum power rating as defined in the applicable part(s) of the rules. 21.904(b): 39 dBW EIRP 74.935(b): 39 dBW EIRP 2.1033(c)8 The dc voltages applied to and dc currents into the several elements of the final radio frequency amplifying device for normal operation over the power range. See block diagram in exhibit 4 2.1033(c)9 Tune-up procedure over the power range, or at specific operating power levels. See tune-up information in exhibit 12 2.1033(c)10 A schematic diagram and a description of all circuitry and devices provided for determining and stabilizing frequency, for suppression of spurious radiation, for limiting modulation, and for limiting power. See schematics in exhibit 5. See circuit descriptions in exhibit 12. 2.1033(c)11 A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. See exhibit 1 FCC ID: PHX-MMDS-CPE1 Page 3 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 2.1033(c)12 Photographs (8”x10”) of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. Insofar as these requirements are met by photographs or drawings contained in instruction manuals supplied with the certification request, additional photographs are necessary only to complete the required showing. See photographs in Exhibit 9 2.1033(c)13 For equipment employing digital modulation techniques, a detailed description of the modulation system to be used, including the response characteristics (frequency, phase and amplitude) of any filters provided, and a description of the modulating wavetrain, shall be submitted for the maximum rated conditions under which the equipment will be operated. See Exhibit 12 2.1033(c)14 The data required by §§ 2.1046 through 2.1057, inclusive, measured in accordance with the procedures set out in § 2.1041 See Test Report measurements in Exhibit 6 2.1033(c)15 The application for certification of an external radio frequency power amplifier under part 97 of this chapter need not be accompanied by the data required by paragraph (b)(14) of this section. In lieu thereof, measurements shall be submitted to show compliance with the technical specifications in subpart C of part 97 of this chapter and such information as required by § 2.1060 of this part. Not applicable 2.1033(c)16 An application for certification of an AM broadcast stereophonic exciter-generator intended for interfacing with existing certified, or formerly type accepted or notified transmitters must include measurements made on a complete stereophonic transmitter. The instruction book must include complete specifications and circuit requirements for interconnecting with existing transmitters. The instruction book must also provide a full description of the equipment and Not applicable FCC ID: PHX-MMDS-CPE1 Page 4 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 measurement procedures to monitor modulation and to verify that the combination of stereo exciter-generator and transmitter meet the emission limitations of § 73.44. 2.1033(c)17 A single application may be filed for a composite system that incorporates devices subject to certification under multiple rule parts, however, the appropriate fee must be included for each device. Not applicable FCC ID: PHX-MMDS-CPE1 Page 5 of 5 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 2 Cover Letters Test Report Summary CFR Rule Part Requirement Test Result 2.1046 RF Output Power Pass 2.1047 Modulation Characteristics Pass 2.1049 Occupied Bandwidth Pass 2.1051 Spurious Emissions at Antenna Terminals Pass 2.1053 Field Strength of Spurious Radiation Pass 2.1055 Frequency Stability Pass 1.1310 Radio Frequency Radiation Exposure Limits Pass 2.1091 Radio Frequency radiation exposure evaluation: mobile devices. Pass Exhibit Summary Exhibit Section Contents 1 FCC ID Label / Location Information 2 Attestation Statement and Cover Letters 3 External Photographs 4 Block Diagrams 5 Schematics 6 Test Report 7 Test Setup Photographs 8 Installation and Operating Manual 9 Internal Photographs 10 Parts List 11 RF Exposure Information 12 Operational Description 13 Co…

Text truncated - open the document above for the full version.

FCC ID: PHX-MMDS-CPE1 Page 1 of 1 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 3 External Photographs

FCC ID: PHX-MMDS-CPE1 Page 1 of 2 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 1 FCC Labeling Requirements and Information 4/16/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: FCC Labeling Requirements FCC ID: PHX-MMDS-CPE1 The following label information is required by the FCC Rules and Regulations for certified devices. Thank you for your attention to these matters. Sincerely, Tim Blom NextNet Wireless, Inc. FCC ID: PHX-MMDS-CPE1 Page 2 of 2 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 1 ID Label / Location Information The FCC ID label will be attached to the CPE unit with a permanent adhesive. Label sample Photo showing label location on CPE unit FCC ID:FCC ID: PHX-MMDS-CPE1 This device complies with Part 15 of the FCC Rules. Part Number:Part Number: 900-0010-1000 <Part number Barcode > SN:SN: 1234X123XAAX87654321 <Serial Number Barcode > NextNet Wireless Inc. Minneapolis, MN 55431

FCC ID: PHX-MMDS-CPE1 Page 1 of 2 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 1 FCC Labeling Requirements and Information 4/16/2001 NextNet Wireless, Inc. 9555 James Avenue South Suite 270 Bloomington, MN 55431 RE: FCC Labeling Requirements FCC ID: PHX-MMDS-CPE1 The following label information is required by the FCC Rules and Regulations for certified devices. Thank you for your attention to these matters. Sincerely, Tim Blom NextNet Wireless, Inc. FCC ID: PHX-MMDS-CPE1 Page 2 of 2 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 1 ID Label / Location Information The FCC ID label will be attached to the CPE unit with a permanent adhesive. Label sample Photo showing label location on CPE unit FCC ID:FCC ID: PHX-MMDS-CPE1 This device complies with Part 15 of the FCC Rules. Part Number:Part Number: 900-0010-1000 <Part number Barcode > SN:SN: 1234X123XAAX87654321 <Serial Number Barcode > NextNet Wireless Inc. Minneapolis, MN 55431

FCC ID: PHX-MMDS-CPE1 Page 1 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs FCC ID: PHX-MMDS-CPE1 Page 2 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs RF Board component side (no shields) FCC ID: PHX-MMDS-CPE1 Page 3 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs RF Board component side (with shields) FCC ID: PHX-MMDS-CPE1 Page 4 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs RF Board solder side FCC ID: PHX-MMDS-CPE1 Page 5 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs Logic Board component side FCC ID: PHX-MMDS-CPE1 Page 6 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs Logic Board solder side FCC ID: PHX-MMDS-CPE1 Page 7 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs Antenna FCC ID: PHX-MMDS-CPE1 Page 8 of 8 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 9 Internal Photographs Antenna (copper side)

FCC ID: PHX-MMDS-CPE1 Page 1 of 7 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 11 RF Exposure Information FCC ID: PHX-MMDS-CPE1 Page 2 of 7 NextNet Wireless, Inc 9555 James Ave. South Suite 270 Bloomington, MN 55431 Exhibit 11 Radio Frequency Exposure Name of Test: Radio Frequency Radiation Exposure Evaluation Rule Part Number: 1.1307, 1.1310, 2.1091 1.1307 Actions that may have a significant environmental effect, for which Environmental Assessments (EAs) must be prepared. TABLE 1—TRANSMITTERS, FACILITIES AND OPERATIONS SUBJECT TO ROUTINE ENVIRONMENTAL EVALUATION Multipoint Distribution Service (subpart K of part 21). Non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and power > 1640 W EIRP Building-mounted antennas: power > 1640 W EIRP MDS licensees are required to attach a label to subscriber transceiver or transverter antennas that: (1) provides adequate notice regarding potential radio frequency safety hazards, e.g., information regarding the safe minimum separation distance required between users and transceiver antennas; and (2) references the applicable FCC-adopted limits for radio frequency exposure specified in § 1.1310. Experimental, auxiliary, and special broadcast and other program distributional services (part 74). Subpart I: non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and power > 1640 W EIRP Building-mounted antennas: power > 1640 W EIRP ITFS licensees are required to attach a label to subscriber transceiver or transverter antennas that: (1) provides adequate notice regarding potential radio frequency safety hazards, e.g., information regarding the safe minimum separation distance required between users and transceiver antennas; and (2) references the appl…

Text truncated - open the document above for the full version.