PJUGH94922.4G ANALOG CORDLESS PHONE WITH CID AND DAM

2.4 GHz Cordless Telephone with Digital Answering Machine & Caller ID on Call Waiting 40 CHANNEL AUTOSCAN WITH 4 SEPARATE MAILBOXES Model GH9492 OWNER’S MANUAL INSTALLATION AND OPERATING INSTRUCTIONS PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. KEEP FOR YOUR REFERENCE. For installation information, please see “Getting Started” instructions on page 6 or your separate Quick Start Guide. Visit Us on the Web: www.uselectronics.info © 2004 Bellsouth Corporation 88 BELLSOUTH Congratulations on your selection of a qualityBellSouthproduct. With proper care, and by following the set-up and user instructions in this Owner’s Manual, this unit will provide you with years of trouble-free service. BellSouthis committed to providing quality products that fit your needs. We would like to have any comments or suggestions you might have on this product. You may mail your comments to: U.S. Electronics 105 Madison Avenue New York, NY 10016 When examining your newBellSouthcordless telephone, you will find an array of special features including: CORDLESS TELEPHONE FEATURES Filtered Sound TM System- Gets considerably less noise than conventional cordless telephones because of a special circuit which delivers the clearest possible reception. 40 Channel Auto Scan- Press thebutton on theHANDSETto find and lock on to the clearest channel for any call. Desk Mount -Use this equipment as a desk phone. TONE or PULSE Dialing- Use this phone for either TONE (push-button) or PULSE (rotary) dialing. Automated Functions- Redial the last number called and automatic STANDBY mode. Security- Ensures greater privacy because a built-in security code with 65,536 combinations prevents use of your telephone line by another nearby cordless phone. Dependable Battery- Recharge your BATTERY PACK many times with the built-in charger. The battery low warning tone tells you when the BATTERY PACK needs recharging. (See page 38.) Special Services- Use thebutton to access special services such as Call Waiting supplied by your telephone company or company switchboard. STANDBY Mode- When in STANDBY mode (ON-HOOK), the phone is capable of receiving a call. When theHANDSETis on theBASE UNIT, it is automatically in the STANDBY mode (ON-HOOK). When theHANDSETis taken off theBASE UNIT, it remains in the STANDBY mode until you activate thebutton. Battery Power Saver- Once fully charged, in STANDBY mode, theHANDSETcan receive/send calls for a maximum of five days without the need for recharging. Length of charge depends on frequency of use. Luminous LCD Screen- The LCD Screen emits light for 5 seconds every time you press any of the buttons on theHANDSET. HANDSET Ringer Level- Select the ringer volume level (HI, LOW, OFF). HANDSET VOLUME CONTROL Switch- Select the receiver volume level (HI, MID, LOW). HEADSET JACK- Your telephone can utilize a headset for hands-free communication. BELT CLIP- Use the BELT CLIP to hang yourHANDSETon your belt. flash flash scan delete Special Features CALLER ID SYSTEM Multi-Function Large LCD Screen- Shows the number you are dialing, and with Caller ID service (available through subscription from your local telephone company), displays information about the caller before you answer the call. Name and Number PHONEBOOK- Stores up to 40 names and numbers so that you can call them with a single key stroke. Caller List- Available with Caller ID service. Stores up to 80 calls to keep track of everyone who called. The name, phone number, time, and date of the call are recorded. Allows you to return their calls with a single key stroke. Preferred Calls- You can mark the name and number of a welcome caller in the PHONEBOOK. When that number calls in, the caller’s name will appear on the LCD Screen and a special ring sound will be heard. Blocked Calls- You can mark the name and number of an unwelcome caller in the PHONEBOOK. When that number calls in, the caller’s name will appear on the LCD Screen and the ringer will be disabled. Repeat Call Indicator- Shows if a new incoming call has called more than once. Out of Area Call Indicator- Advises you that the incoming call is not in a Caller ID service area, or does not support the Caller ID system. Private Call Indicator- Advises you that the caller’s name and/or telephone number of the incoming call is blocked by the system. Call Waiting Service- Displays the name and number of the second caller, if you have subscribed to call waiting service from your local telephone company (See page 15). Voice Mail- Indicates message waiting signal if you subscribed to Voice Mail message service and requested Visual Message Indication from your local telephone company (see page 15). This telephone also detects a Stutter Dial Tone signal every time there is a Voice Mail message for your Voice Mail message provider if you have subscribed to Voice Mail message service. ANSWERING SYSTEM FEATURES Fully Digital Answering System- Provides a full range of answering functions without using cassette tapes. Digital Memory- Allows recording of memos and messages. Two Digit LED Message Display- Indicates the number of messages, indicates the status of the system. Ring-Detection Selectable- Choose the number of times the telephone rings before the system answers. Voice Day/Time Stamp- Systems tells the day and time of each received message or recorded memo. Message Alert- The ability to generate a sound signal when new messages are recorded. Call Screening- The ability to intercept a call when the unit is recording an incoming message (ICM). Mailboxes- Allows four separate individuals to receive their own incoming messages. Auto Disconnection- Will automatically stop answering whenHANDSETof any phone on the same line is lifted. Fast Message Skip Function- Skips to the next message. Remote Control Capable- Can be accessed through an outside line (Tone telephone) via 3- digit access code. BASE UNIT SPEAKERPHONE FEATURE Special Features HANDSET Controls 1.HANDSET ANTENNA 2.NEW CALL/MSG (MESSAGE) WAITING LED In…

Text truncated - open the document above for the full version.

GH9492bsbd.sch-1 - Sun May 16 17:16:45 2004 GH9492hsbd.sch-1 - Sun May 16 17:20:06 2004

ShenZhen JingNeng Telecom Technology Co., Ltd BaiMenQian Industrial Zone, Shawan, BuJi Town, LongGang District, ShenZhen City, P.R China Tel:86-755-28711237 Fax:86-755-28711240 Email: [email protected] Request for Confidentiality Federal Communications Commission Authorization and Evaluation Division Sub.: Confidentiality Request regarding application for certification of FCC ID: PJUGH9492 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: l Schematics l Part List l Block diagram l Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Jason Wu / QA Manager ShenZhen JingNeng Telecom Technology Co., Ltd

External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 1/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 2/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 3/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 4/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 5/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 6/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 External Photos of 2.4GHz Analog Cordless Phone with CID and DAM －－ 7/7 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

FORBASE R&D MODEL NO.:GH9492SCALE 1/1 ENGRAVING ARTWORK:GH9492-E1-1 DATE: 12-Feb.-04 DESIGNED BY: WUYINYAN CHECKED BY: DL APPROVED BY: ALAN CHENG 9VDC 500mA TEL LINE R 2002627 CONFORMS TO ANSI/UL STD, 60950 US HAC THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. TELEPHONE EQUIPMENT Licensed under U.S. Patent No. 5,263,084 REMOTE ACCESS CODES PRIMARY MAILBOX: 999 MAILBOX 1:555 MAILBOX 2:666 MAILBOX 3:777 MAILBOX 4:888 MODEL NO. GH9492 0400700001 S/NO.: MADE IN CHINA COMPLIES WITH PART 68 FCC RULES, FCC REG. NO.: US: 6RUW900BGH9492 USOC: RJ11C REN: 0.0B PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE CM QC 1A ACC R4.00mm 40mm 8.00mm 9.50mm 21.00mm 42.00mm 29.50mm 28.00mm 13.00mm

Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 1/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 2/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 3/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 4/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 5/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 6/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 7/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 8/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 9/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 10/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Internal Photos of 2.4GHz Cordless Phone with CID and DAM (Base) －－－ 11/11 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

ShenZhen JingNeng Telecom Technology Co., Ltd BaiMenQian Industrial Zone, Shawan, BuJi Town, LongGang District, ShenZhen City, P.R China Tel:86-755-28711237 Fax:86-755-28711240 Email: [email protected] Model:GH9492 OPERATION DESCRIPTION n HANDSET 1. RF/Audio Section The radio link Handset and Base is full duplex at 2400/2483.5 MHz with the 40 channels. FM modulation is used for the link. The 1 st IF frequency is 10.7MHz and the 2 nd IF frequency is 450KHz. The operating frequency for the cordless phone is selected from one of the following channels and controlled by the synthesizer U2 that is programmed by the MCU. This section is common to both handset and base as the same ICs are used LMX1602(U2), KA3361(U1) is made up of dual serial input PLL frequency synthesizer with 1000MHz prescaler. KA3361 is a narrow-band IF detector IC. 1.1 Receiver The receiver section is made of double conversion with 10.7MHz as the first and second IF. Rx signal from the duplexer circuit is amplified by a Low Noise RF transistor and passed to 450KHz IF in the internet mixer of U1. Voice/data signal is demodulated and output from pin9 of U1. The demodulated signal is then divided into two paths, a path is fed into the data amplifier Q7, Q13. The other path will go through a de-emphasized amplifier and an expander in IC1. Recovered signal scan be muted by the pin 13 of IC 1, the volume level of the signal can be controlled by the push switch SW1. 1.2 Transmitter Audio signal (from Microphone for headset/Tip & Ring for base) is first fed into the amplifier and compressor inside IC1 (U5 for Base). The signal will pass through a limiter. The AGC and the limiter have the property to limit the maximum signal that feed into the transmitter so that the RF deviation is limited. The transmitter section mainly divided into two parts. They are the voice/data modulator and the Tx power amplifier. The voltage-controlled oscillator VCO operated at the Tx frequency controlled by the synthesizer is modulated by the audio and data signals. Modulated signal is amplified by the RF amplified and sending the signal to the duplexer for radiation by the antenna. 1.3 Band-Pass Filter (BFF) The function of the two Band-Pass Filter(BPF) is to individual fed the transmitting and receiving signals to a common antenna while providing isolation and rejection of interference and other spurious signals. ShenZhen JingNeng Telecom Technology Co., Ltd BaiMenQian Industrial Zone, Shawan, BuJi Town, LongGang District, ShenZhen City, P.R China Tel:86-755-28711237 Fax:86-755-28711240 Email: [email protected] 1.4 Alerter The alerting signals include the following: Ringing, Paging, key beep and Low battery warning tone. These tones are generated by the MCU to the alerter through the driving circuit formed Q6 and the associated components. 1.5 Headset microphone The condenser microphone is in the handset and it biased by the resistor R6 The signal is applied to the amplifier inside IC1. 2. MCU 2.1 Battery Detect The voltage detector is composed of U1 that is used to detect battery low condition. The detecting accuracy of the voltage detector is +/- 0.2V. The detect pin BAT-LOW is connected to the pin 50 of MCU. 2.2 Carrier Detection This 40 channels cordless has the features of auto-scanning. This is done by the detection of the RSSI at pin 70 of MCU of handset. During PHONE on or CHANNEL changing, the MCU will select the clearest channel for the RF communication. n BASE 3. RF/Audio sections The operation of the RF/Audio section is similar to that of the handset. 4. Telephone Network 4.1 Telephone interface Fuse FUSEx is for over-voltage protection. Transistor Q31, Q32 controls the on/off hook state and pulse dialing. ShenZhen JingNeng Telecom Technology Co., Ltd BaiMenQian Industrial Zone, Shawan, BuJi Town, LongGang District, ShenZhen City, P.R China Tel:86-755-28711237 Fax:86-755-28711240 Email: [email protected] 4.2 Ring Detect When ring signal is present on the Tip Ring, and envelope waveform of the ring pattern will transfer to pin 3 of MCU by the LM324 pin 1 The MCU will read this waveform and determine whether it will send ringer command, 4.3 Sidetone Cancellation Network The sidetone cancellation is a hybrid circuit of the Tx and Rx paths of the telephone circuit formed by the Q28. 5. MCU 5.1 Charging Network Base charging circuit provides a DC current for handset battery. Resistor R31 controls the current flow. 5.2 Carrier Detection This is similar to the handset counterpart. 6. Digital Answer System Digital Answer System is consist of a DSP chip (MX93132,U7) and flash memory chip (MX29F400T, U4) 6.1 MX93132 provides speech processing/management modules, including speech compression/ decompression silence management, telephone line signal processing RAM Management line echo cancellation and acoustical echo cancellation, etc. 6.2 MX29F400T: Memory Chip – resources of DAS.

2.4gRFBs10.sch-1 - Mon May 17 08:44:24 2004 9492HS10.sch-1 - Sun May 16 17:10:14 2004 2.4gRFHs10.sch-1 - Mon May 17 08:42:09 2004

Test Report ------------------------------------------------------------------------------- 1/32 Report No.: K1015572, 2.4GHz Analog Cordless Phone with CID and DAM, FCC Part 15.249 Training Research Co., Ltd. TEL:886-2-26935155, Fax:886-2-26934440 MEASUREMENT REPORT of CORDLESS TELEPHONE Applicant : ShenZhen JingNeng Telecom Technology Co., Ltd. EUT : 2.4GHz Analog Cordless Phone with CID and DAM Model No. : GH9492; XG2404 FCC ID : PJUGH9492 Report No. : K1015572 Test by : Training Research Co., Ltd. TEL : 886-2-26935155 FAX : 886-2-26934440 No. 255, Nan-yang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. Test Report ------------------------------------------------------------------------------- 2/32 Report No.: K1015572, 2.4GHz Analog Cordless Phone with CID and DAM, FCC Part 15.249 Training Research Co., Ltd. TEL:886-2-26935155, Fax:886-2-26934440 CERTIFICATION We here by verify that: The test data, data evaluation, test procedures and equipment configurations shown in this report were made mainly in accordance with the procedures given in ANSI C63.4 (1992) as a reference. All tests were conducted by Training Research Co., Ltd., No. 255, Nan-yang Street, Shijr, Taipei Hsien 221, Taiwan. Also, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report is in compliance with the technical requirements set forth in the FCC Rules Part 15 Subpart C Section 15.249. Applicant : ShenZhen JingNeng Telecom Technology Co., Ltd. Applicant address : BaiMenQian Industrial Zone, ShaWan, BuJi Town, LongGang District, ShenZhen City, P.R China Model Name : GH9492; XG2404 FCC ID : PJUGH9492 Test Date : May 24, 2004 Prepared by: Approved by: JACK TSAI FRANK TSAI Test by : Training Research Co., Ltd. TEL : 886-2-26935155 FAX : 886-2-26934440 No. 255, Nan-yang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. Test Report ------------------------------------------------------------------------------- 3/32 Report No.: K1015572, 2.4GHz Analog Cordless Phone with CID and DAM, FCC Part 15.249 Training Research Co., Ltd. TEL:886-2-26935155, Fax:886-2-26934440 Tables of Contents I. GENERAL 1.1 Introduction .................................................................................................................. 5 1.2 Description of EUT ...................................................................................................... 5 1.3 Description of Support Equipment ............................................................................... 6 1.4 Configuration of System Under Test ........................................................................... 6 1.5 Test Procedure .............................................................................................................. 7 1.6 Location of the Test Site .............................................................................................. 7 1.7 General Test Condition ................................................................................................ 7 II. Conducted Emissions Measurements 2.1 Test Condition & Setup ............................................................................................... 8 2.2 List of Test Instruments ............................................................................................... 8 2.3 Test Result of Conducted Emissions ........................................................................... 9 III. Radiated Emissions Measurements 3.1 Test Condition & Setup .............................................................................................. 12 3.2 List of Test Instruments .............................................................................................. 13 3.3 Test Result of Radiated Emissions ............................................................................. 14 3.4 Test Result of Spurious Radiated Emissions .............................................................. 15 IV. Verify Frequencies and Channels ............................................................................... 23 Appendix A .......................................................................................................................... 24 Appendix B ........................................................................................................................... 27 Test Report ------------------------------------------------------------------------------- 4/32 Report No.: K1015572, 2.4GHz Analog Cordless Phone with CID and DAM, FCC Part 15.249 Training Research Co., Ltd. TEL:886-2-26935155, Fax:886-2-26934440 TABLES Table 1 Power Line Conducted Emissions [Channel 01]................................................. 9 Table 2 Power Line Conducted Emissions [Channel 40]................................................ 10 Table 3 Power Line Conducted Emissions [Charging by base] ...................................... 11 Table 4 Fundamental Emissions .................................................................................... 14 Table 5 Radiated Emissions [Base CH 01, Horizontal, 30MHz to1GHz] ...................... 15 Table 9 Radiated Emissions [Base CH 01, Vertical, 30MHz to 1GHz] ...................... 15 Table 7 Radiated Emissions [Base CH 01, Horizontal, 1GHz to 25GHz] .................... 16 Table 8 Radiated Emissions [Base CH 01, Vertical, 1GHz to 25GHz] ........................ 16 Table 9 Radiated Emissions [Base CH 40, Horizontal, 30MHz to 1GHz] ................... 17 Table 10 Radiated Emissions [Base CH 40, Vertical, 30MHz to 1GHz] ......................... 17 Table 11 Radiated Emissions [Base CH 40, Horizontal, 1GHz to 25GHz] .................... 18 Table 12 Radiated Emissions [Base CH 40, Vertical, 1GHz to 25GHz] ........................ 18 Table 13 Radiated Emissions [Handset CH 01, Horizontal, 30MHz to 1GHz]................ 19 Table 14 Radiated Emissions [Handset CH 01, Vertical, 30MHz to 1GHz] .................... 19 Table 15 Radiated Emission…

Text truncated - open the document above for the full version.

Test Setup Photos ------------------------------------------------------------------------- 1/6 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Conducted Test Setup Placement: (Charging mode) Front View of the Test Configuration Side View of the Test Configuration Test Setup Photos ------------------------------------------------------------------------- 2/6 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Conducted Test Setup Placement: (Operating mode) Front View of the Test Configuration Side View of the Test Configuration Test Setup Photos ------------------------------------------------------------------------- 3/6 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Radiated Test Setup Placement: (BASE) Front View of the Test Configuration of X-axis Rear View of the Test Configuration of X-axis Test Setup Photos ------------------------------------------------------------------------- 4/6 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Radiated Test Setup Placement: (Handset) Front View of the Test Configuration of X-axis Rear View of the Test Configuration of X-axis Test Setup Photos ------------------------------------------------------------------------- 5/6 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Radiated Test Setup Placement: (Handset) Front View of the Test Configuration of Y-axis Rear View of the Test Configuration of Y-axis Test Setup Photos ------------------------------------------------------------------------- 6/6 Applicant: ShenZhen JingNeng Telecom Technology Co., Ltd. FCC ID: PJUGH9492 Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440 Radiated Test Setup Placement: (Handset) Front View of the Test Configuration of Z-axis Rear View of the Test Configuration of Z-axis