PLNBONTEC-T011Transmitter Keyless

Remote Keyless Entry (BONTEC-T011) BONTEC Co., Ltd. #27-31, HANCHUN-RI, DUCK-SAN -MYUN,, JINCHUN-GUN,CHUNG-BUK,KOREA - INDEX - - An outline - Description of Transmitter and Receiver FCC NOTICE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC FULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITION: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. - Consult the dealer of an experienced radio/TV technician for help. NOTE : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. An outline of Transmitter and ETACS 1. How to use BONTEC 1. How to use BONTEC1. How to use BONTEC 1. How to use BONTEC- -- -T011,R011 T011,R011T011,R011 T011,R011 - BONTEC-T011,R011 is Remote Keyless System. - This unit control door lock/unlock with wireless. - Lock button push , then door lock. - Unlock button push, then door unlock. - Trunk button push, then Trunk Open - Panic button push, then Panic Alarm 2. Introduction of Transmitter 2. Introduction of Transmitter2. Introduction of Transmitter 2. Introduction of Transmitter - Transmitter has three button - Button marking are LOCK, UNLOCK, TRUNK, PANIC - Transmitter use thee voltage battery - Frequency is 315Mhz - Modulation item is SAW Resonator - Transmitter use Rolling code algorithm 3. Introduction of Receiver 3. Introduction of Receiver3. Introduction of Receiver 3. Introduction of Receiver - Receiver control car door - Receiver has RF module(315) - RF module use superregentive circuit - Receiver send Door Lock/Unlock/Trunk open/Panic to ETACS - Receiver has internal eeprom that save code Description of Transmitter and ETACS 1. PRIMARY FUNTION - Remote door lock/unlock - Remote Back Glass Open/panic - LED turn on ( When button is pushed ) - Operating distance : 7~ 10 m - Id input(setting mode) 2. ELECTRICAL CHARACTERISTICS TRANSMITTER RECEIVER Operating voltage 3 VDC 10 ~ 16 VDC Consumption current Max 20mA Max 5mA Operating frequency 315㎒ Power 10mW under - Sensitivity - -100dBm(typical) Operating temperature -20 ~ +60°C -30 ~ +80°C etc AM modulation Superheterodyne 3. DESCRIPTION MODE 1) Mode Mode ID INPUT (Setting Mode) Normal Mode B+ ON ON CAR KEY - OFF SETTING ON OFF 2) Id input(Setting Mode) When Setting Mode, lock button push, 4. OPERATING DIAGRAM 1) TRANSMITTER 5. OPERATING DIAGRAM * DESCRIPTION OF OUTPUT SIGNAL KEYLESS SWITCH IG SWITCH SET SWITCH LOCK UNLOCK START SETTING END SETTING DOOR CONTROLLER LOCK/UNLOCK START SETTING / END SETTING BATTERY <- START -> <- " 0 " -> <- " 1 " -> <- T3 -> T2 <-T1-> T2<-T1-> T1 : 24 msec T2 : 8 msec T3 : 49 msec * A cause BATTERY IG SW. SET SW. KEYLESS SW.OPERATING MODE SETTING MODE OFF OFF OFF ENABLE DISABLE OFF OFF ON DISABLE DISABLE OFF ON OFF DISABLE DISABLE OFF ON ON DISABLE DISABLE ON OFF OFF DISABLE DISABLE ON OFF ON DISABLE DISABLE ON ON OFF DISABLE DISABLE ON ON ON DISABLE ENABLE LOCK TRA NSMITTE R RECEIVERDOOR CONTROLLER R.K.E(Remote keyless entry) LOCK DOOR UNLOCK 433.92MHz UNLOCK END SETTING START SETTING ANTENNA LOCK / UNLOCK Signal

Block diagram from Transmitter A. TRANSMITTER PATTERN ANTENNA RF OUT SAW RESONATO AMP ENCODER (CPU) FILTER (LC)

SK TECH CO., LTD. Page 1 of 2 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 External Photographs of EUT SK TECH CO., LTD. Page 2 of 2 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011

SK TECH CO., LTD. Page 1 of 1 SKT SKTOS-02067 FCC ID :PLNBONTEC-T011 FCC ID Label Sample

SK TECH CO., LTD. Page 1 of 1 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 FCC ID Sample Label & Location Information LABELLING REQUIREMENTS PER ∫∫∫∫ ∫∫∫∫∫∫∫∫ ∫∫∫∫2.928 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. FCC ID : PLNBONTEC-T011

SK TECH CO., LTD. Page 1 of 3 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 Internal Photographs of EUT SK TECH CO., LTD. Page 2 of 3 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 SK TECH CO., LTD. Page 3 of 3 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011

SK TECH CO., LTD. Page 1 of 1 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 Operational Description This product is a remote key to control (lock & unlock) the door of a car. (This unit control door lock/unlock with wireless.) The using of this product is very easy and simply. SectionI II I. Primary Function - Remote door lock/unlock - Remote Back Glass Open/panic - LED turn on (When button is pushed) - Operating distance : 7 ~ 10m - Id input(setting mode) SectionII IIII II. How to using of this Wireless Key - Lock button push, then door lock. - Unlock button push, then door unlock. - Trunk button push, then Trunk Open - Panic button push, then Panic Alarm SectionIII IIIIII III. .. . Introduction of Transmitter - Transmitter has three button. - Button marking are LOCK, UNLOCK, TRUNK, PANIC - Transmitter use three voltage battery - Frequency is 315MHz - Modulation item is SAW Resonator - Transmitter use Rolling code algorithm

Schematic diagram from Transmitter A. TRANSMITTER C2 N.U D1 DA224 S4 SKQGADE010 x 4 21 R3 47k S1 21 C5 6pF S2 21 X1 RO2073A or RO2073A-1 R1 10 C6 104 C3 N.U R6 N.U C1 47pF S3 21 R5 N.U R9 1k V1 3Vdc Q1 2SC3356 1 2 3 R2 51 R7 N.U R4 100 LED1 SML010LT C7 104 R8 N.U ANT C4 1.5pF U1 HCS300 1 2 3 4 6 7 8 S1 S2 S3 S4 PWM /LED VCC

SK TECH CO., LTD. Page 1 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 Certificate of Compliance Test Report No.: SKTOS-02067 NVLAP CODE : 200220-0 Applicant: BONTEC CO., LTD. Applicant Address: #27-31, Hanchun-Ri, Ducksan-Myun, Jinchun-Gun, Chungbuk, Korea Product: Transmitter keyless FCC ID: PLNBONTEC-T011 Model No.: BONTEC-T011 Receipt No.: SKE20020615-385 Date of receipt: June 15, 2002 Date of Issue: June 25, 2002 Testing location: SK TECH CO., LTD. 820-2, Wolmoon-Ri, Wabu-Up, Namyangju-Si, Kyunggi-Do, Korea Test Standards: ANSI C63.4 / 2000 Rule Parts: FCC part 15 Subpart C Equipment Class : Part 15 Security/Remote Control Transmitter Test Result: The above mentioned product has been tested and passed. Prepared by:Y.H. Kang Tested by:J.S.Hyun/Engineer Approved by: K.S.Kim/Manager & Chief Engineer Signature Date Signature Date Signature Date Other Aspects : Abbreviations : · OK, Pass = passed · Fail = failed · N/A = not applicable ☞ ☞☞ ☞ •This test report is not permitted to copy partly without our permission. •This test result is dependent on only equipment to be used. •This test result is based on a single evaluation of one sample of the above mentioned. •This test report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S Government. • We certify that this test report has been based on the measurement standards that is traceable to the national or International standards. NVLAP Lab. Code: 200220-0 SK TECH CO., LTD. Page 2 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 》》 》》》》 》》 Contents 《《 《《《《 《《 Contents 2 List of Tables 2 1. General 3 2. Test Site 3 2.1 Location 3 2.2 List of Test and Measurement Instruments 4 2.3 Test Date 4 2.4 Test Environment 4 3. Description of the tested samples 5 3.1 Rating and Physical characteristics 5 3.2 Submitted Documents 5 4. Measurement Conditions 6 4.1 Modes of Operation 6 4.2 List of Peripherals 6 4.3 Type of Used cables 6 4.4 Test Setup 6 4.5 Uncertainty 6 5. Test and Measurements 7 5.1 Transmission Requirement according to 15.231(a) 7 5.2 Field strength of emissions according to 15.231(b) 8 5.3 Occupied bandwidth according to 15.231(c) 10 》 》》 》List of Tables Table 1 List of test and measurement equipment 4 》 》》 》Appendix: Measured data Appendix 1: Figure of the measured Transmission Duration 11-12 Appendix 2: Table of the measured Field strength 13 Appendix 3: Figure of the measured Occupied bandwidth 14 SK TECH CO., LTD. Page 3 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 1. General This equipment has been shown to be capable of compliance with the applicable technical standards and was tested in accordance with the measurement procedures as indicated in this report. We attest to the accuracy of data. All measurements reported herein were performed by SK Tech Co., Ltd. and were made under Chief Engineer’s supervision. We assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. 2. Test Site SK TECH Co., Ltd. 2.1 Location 820-2, Wolmoon Ri, Wabu-Up, Namyangju-Si, Kyunggi-Do, Korea The test site is in compliance with ISO/IEC 17025 for general requirements for the competence of testing and calibration laboratories. This laboratory is accredited by NVLAP for NVLAP Lab. Code : 200220-0 and DATech for DAR-Registration No.:TTI-P-G155/97-10 SK TECH CO., LTD. Page 4 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 2.2 List of Test and Measurement Instruments Table 1 : List of Test and Measurement Equipment z Radiated Disturbance Kind of Equipment Type S/N Calibrated until EMI Receiver ESVS 10 825120/013 02.2003 EMI Receiver ESVS 10 834468/008 11.2002 Spectrum Analyzer R3361A 11730187 07.2003 Amplifier 8447F 3113A05153 06.2003 Log Periodic Antenna UHALP9107 1819 02.2003 Horn Antenna SAS-200/571 304 04.2003 Biconical Antenna BBA9106 91031626 02.2003 Antenna Mast 5907 N/A N/A Antenna & Turntable controller 5906 N/A N/A Amp & Receiver connection cables N/A N/A N/A 50Ω Switcher MP59B 6100214538 N/A 2.3 Test Date Date of Application : June 15, 2002 Date of Test : June 17, 2002 2.4 Test Environment See each test item’s description. SK TECH CO., LTD. Page 5 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 3. Description of the tested samples The EUT is Transmitter Keyless. 3.1 Rating and Physical Characteristics TRANSMITTER RECEIVER Operating Voltage 3 VDC 10 ~ 16 VDC Consumption Current Max 20mA Max 5mA Operating frequency 315MHz Power 10mW under - Sensitivity - -100dBm(typical) Operating temperature -20 ~ +60°C -30 ~ +80°C Etc AM modulation Super-heterodyne 3.2 Submitted Documents N/A SK TECH CO., LTD. Page 6 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 4. Measurement Conditions Testing Input Voltage : DC 3V 4.1 Modes of Operation The EUT was in the following operation mode during all testing; The EUT is in the mode of pushing the Lock / Unlock key button. 4.2 List of Peripherals Description Manufacturer Model Name Serial No. FCC ID N/A 4.3 Type of Used Cables Description Length Type of shield Manufacturer Remark N/A 4.4 Test Setup The test setup photographs showed the external supply connections and interfaces. 4.5 Uncertainty 1) Radiated disturbance Uc (Combined standard Uncertainty) = ±1.9dB Expanded uncertainty U = KUc K = 2 ∴ U = ±3.8dB 2) Conducted disturbance Uc = ±0.88dB U = KUc = 2xUc = ±1.8dB SK TECH CO., LTD. Page 7 of 14 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 5. Test and Measurements 5.1 Transmission Requirement according to § 15.231(a)(1) Results: PASS The results of the transmission duration and duty cycle are shown in Appendix 1. The duty cycle correction factor was computed to be –7.74 dB. The intentional radiator is restricted to the transmission of a control signal such as those used with alarm systems, door openers, remote switches, etc. Continuous transmissions, such as voice or video, and data transmissions are not permitted. According to §15.231(a)(1), a manually operated transmitter shall employ a switch that will automati…

Text truncated - open the document above for the full version.

SK TECH CO., LTD. Page 1 of 1 SKT SKTOS-02067 FCC ID : PLNBONTEC-T011 Test set up photos Photograph 1: Setup for Radiated Emissions