PPD-ARS63SLow Power 1x1 802.11 b/g/n (SDIO) Card

ARS63-S Product name： ：： ： Low Power 1x1 802.11 b/g/n (SDIO) Card © 2000–2009 by Atheros Communications, Inc. All rights reserved. Atheros ® , Atheros Driven ® , Atheros XR ® , Driving the Wireless Future ® , ROCm ® , Super AG ® , Super G ® , Total 802.11n ® , and Wake on Wireless ® are registered by Atheros Communications, Inc. Atheros SST™, Signal-Sustain Technology™, the Air is Cleaner at 5-GHz™, XSPAN™, Wireless Future. Unleashed Now.™, and 5-UP™ are trademarks of Atheros Communications, Inc. The Atheros logo is a registered trademark of Atheros Communications, Inc. All other trademarks are the property of their respective holders. Notice The information in this document has been carefully reviewed and is believed to be accurate. Nonetheless, this document is subject to change without notice, and Atheros Communications, Inc. (Atheros) assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the contained information, or to notify a person or organization of any updates. Atheros reserves the right to make changes, at any time, in order to improve reliability, function or design and to attempt to supply the best product possible. Atheros does not represent that products described herein are free from patent infringement or from any other third party right. No part of this document may be reproduced, adapted or transmitted in any form or by any means, electronic or mechanical, for any purpose, except as expressly set forth in a written agreement signed by Atheros. Atheros or its affiliates may have patents or pending patent applications, trademarks, copyrights, maskwork rights or other intellectual property rights that apply to the ideas, material and information expressed herein. No license to such rights is provided except as expressly set forth in a written agreement signed by Atheros. ATHEROS MAKES NO WARRANTIES OF ANY KIND WITH REGARD TO THE CONTENT OF THIS DOCUMENT. IN NO EVENT SHALL ATHEROS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL SPECULATORY OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. IN PARTICULAR, ATHEROS SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA TRANSMITTED OR OTHERWISE USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE OR DATA. ATHEROS SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE AS THEY MIGHT OTHERWISE APPLY TO THIS DOCUMENT AND TO THE IDEAS, MATERIAL AND INFORMATION EXPRESSED HEREIN. Atheros Communications, Inc. • iii COMPANY CONFIDENTIAL August 2010 Document Conventions Text Conventions bold Bold type within paragraph text indicates commands, file names, directory names, paths, output, or returned values. Example: The DK_Client package will not function unless you use the wdreg_install batch file. italic Within commands, italics indicate a variable that the user must specify. Example: mem_alloc size_in_bytes Titles of manuals or other published documents are also set in italics. Courier The Courier font indicates output or display. Example: Error:Unable to allocate memory for transfer! Menu The Menu character tag is used for menu items. Example: Choose Edit > Copy. [ ] Within commands, items enclosed in square brackets are optional parameters or values that the user can choose to specify or omit. { } Within commands, items enclosed in braces are options from which the user must choose. | Within commands, the vertical bar separates options. ... An ellipsis indicates a repetition of the preceding parameter. > The right angle bracket separates successive menu selections. Example: Start > Programs > DK > wdreg_install. Notices NOTE: This message denotes neutral or positive information that calls out important points to the text. A note provides information that may apply only in special cases. Atheros Communications, Incorporated 5480 Great America Parkway Santa Clara, CA 95054 t: 408/773-5200 f: 408/773-9940 www.atheros.com Revision History Revision Description of Changes March 2009 Initial Release Atheros Communications, Inc. • v COMPANY CONFIDENTIAL August 2010 Contents Introduction..........................................................................................................8 System Requirements....................................................................................8 Profile Management.............................................................................................8 Create or Modify a Configuration Profile....................................................8 Remove a Configuration Profile...................................................................9 Auto Profile Selection Management....................................................................9 Switching to a Different Configuration Profile................................................10 Import and Export Profiles.................................................................................10 Importing a Profile..............................................................................................10 Exporting a Profile..............................................................................................10 TCP/IP Configuration.......................................................................................10 Configuring the TCP/IP Address for the network device:................................10 General Tab.........................................................................................................11 Advanced Tab.....................................................................................................11 Security Tab........................................................................................................12 Using EAP-TLS Security.........................................…

Text truncated - open the document above for the full version.

Date: 2010/7/8 General declaration We, Atheros Communications, Inc. declares that device does not have “Ad Hoc on non-US frequencies” while applying for the follow product. FCC ID: PPD-ARS63S If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! --------------------------------------------------------------------------- Michael Green / Manager, Global Product Compliance Atheros Communications, Inc.

Date:2010/7/8 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: PPD-ARS63S To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Pursuant to DA 04-1705 of the Commission’s Rules, we request short-term confidential treatment for the following information until Nov. 1, 2010 of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards --------------------------------------------------------------------------- Michael Green / Manager, Global Product Compliance Atheros Communications, Inc.

FCC ID: PPD-ARS63S Report No. : RF990709E01C Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Aug. 06, 2010 Dear Application Examiner, Atheros Communications, Inc., It’s Low Power 1x1 802.11 b/g/n (SDIO) + BT Combo Card, FCC ID: PPD-ARS63SB would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 1. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip AR6003. 2. “The modular transmitter must have its own power supply regulation part no.: AR6003. 3. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 4. “The modular transmitter must be tested in a stand-alone configuration”. The EUT is tested in a stand-alone configuration via an extender. Please see section Photographs of Test Configuration in the test report. 5. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: PPD-ARS63S Report No. : RF990709E01C 6. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 7. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

Printed Color： ：： ： Black 地色 地色地色 地色 ： ：： ：White 材質 材質材質 材質 ： ：： ：一般合成紙 一般合成紙一般合成紙 一般合成紙 粘著材 粘著材粘著材 粘著材 ： ：： ：樹脂系糊 樹脂系糊樹脂系糊 樹脂系糊 Bottom of EUT FCC / IC Label Location Model name ： ：： ：ARS63-S

Page 4 Page 5 Page 6

Report No.: SA990709E01C Report Format Version 3.0.1 Reference No.:990713E08 1 RF EXPOSURE REPORT REPORT NO.: SA990709E01C MODEL NO.: ARS63-S FCC ID: PPD-ARS63S ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Atheros Communications, Inc. ADDRESS: 5480 Great America Parkway, Santa Clara, CA 95054 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan Report No.: SA990709E01C Report Format Version 3.0.1 Reference No.:990713E08 2 RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in our lab, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Report No.: SA990709E01C Report Format Version 3.0.1 Reference No.:990713E08 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm 2 . If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA990709E01C Report Format Version 3.0.1 Reference No.:990713E08 4 6. TEST RESULTS 6.1 Antenna Gain There is one set of antenna provided to this EUT, please refer to the following table: Brand Model Gain(dBi) (included cable loss) Antenna Type Connector Cable Loss(dB) Cable Length WNC 81-EBJ15.005 (Main) 3.62 PIFA IPEX 1.15 300mm 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: 802.11b: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 123.0 0.056 1.0 6 2437 120.2 0.055 1.0 11 2462 125.9 0.058 1.0 802.11g: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 169.8 0.078 1.0 6 2437 239.9 0.110 1.0 11 2462 199.5 0.091 1.0 802.11n (20MHz): Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 147.9 0.068 1.0 6 2437 234.4 0.107 1.0 11 2462 173.8 0.080 1.0

Report No.: RF990709E01C 1 Report Format Version 3.0.1 Reference No.:990713E08 FCC TEST REPORT REPORT NO.: RF990709E01C MODEL NO.: ARS63-S FCC ID: PPD-ARS63S RECEIVED: July 13, 2010 TESTED: July 22 to 27, 2010 ISSUED: Aug. 04, 2010 APPLICANT: Atheros Communications, Inc. ADDRESS: 5480 Great America Parkway, Santa Clara, CA 95054 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 89 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: RF990709E01C 2 Report Format Version 3.0.1 Reference No.:990713E08 Table of Contents 1. CERTIFICATION...........................................................................................5 2. SUMMARY OF TEST RESULTS...................................................................6 2.1 MEASUREMENT UNCERTAINTY................................................................7 3. GENERAL INFORMATION...........................................................................8 3.1 GENERAL DESCRIPTION OF EUT..............................................................8 3.2 DESCRIPTION OF ANTENNA......................................................................9 3.3 DESCRIPTION OF TEST MODES..............................................................10 3.3.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL..............11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS.............................14 3.5 DESCRIPTION OF SUPPORT UNITS........................................................15 3.6 CONFIGURATION OF SYSTEM UNDER TEST.........................................15 4. TEST TYPES AND RESULTS.....................................................................16 4.1 CONDUCTED EMISSION MEASUREMENT..............................................16 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................16 4.1.2 TEST INSTRUMENTS................................................................................16 4.1.3 TEST PROCEDURES.................................................................................17 4.1.4 DEVIATION FROM TEST STANDARD.......................................................17 4.1.5 TEST SETUP..............................................................................................18 4.1.6 EUT OPERATING CONDITIONS................................................................18 4.1.7 TEST RESULTS..........................................................................................19 4.2 RADIATED EMISSION MEASUREMENT...................................................21 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.................................21 4.2.2 TEST INSTRUMENTS................................................................................22 4.2.3 TEST PROCEDURES.................................................................................23 4.2.4 DEVIATION FROM TEST STANDARD.......................................................23 4.2.5 TEST SETUP..............................................................................................24 4.2.6 EUT OPERATING CONDITIONS................................................................24 4.2.7 TEST RESULTS (For transmitter part)........................................................25 4.2.8 TEST RESULTS (For receiver part)............................................................47 4.3 6dB BANDWIDTH MEASUREMENT..........................................................51 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................51 4.3.2 TEST INSTRUMENTS................................................................................51 4.3.3 TEST PROCEDURE...................................................................................52 Report No.: RF990709E01C 3 Report Format Version 3.0.1 Reference No.:990713E08 4.3.4 DEVIATION FROM TEST STANDARD.......................................................52 4.3.5 TEST SETUP..............................................................................................52 4.3.6 EUT OPERATING CONDITIONS................................................................52 4.3.7 TEST RESULTS..........................................................................................53 4.4 99% BANDWIDTH MEASUREMENT..........................................................59 4.4.1 TEST INSTRUMENTS................................................................................59 4.4.2 TEST PROCEDURE...................................................................................59 4.4.3 TEST SETUP..............................................................................................59 4.4.4 EUT OPERATING CONDITIONS................................................................59 4.4.5 TEST RESULTS..........................................................................................60 4.5 MAXIMUM PEAK OUTPUT POWER..........................................................66 4.5.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........66 4.5.2 INSTRUMENTS..........................................................................................66 4.5.3 TEST PROCEDURES.................................................................................66 4.5.4 DEVIATION FROM TEST STANDARD.......................................................66 4.5.5 TEST SETUP…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 990713E08 990713E08 2 RADIATED EMISSION TEST 990713E08 990713E08 3 990713E08