PPD-QCASP1411x1 802.11b/g/n module

Confidential and Proprietary - Qualcomm Atheros, Inc. Not to be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of Qualcomm Atheros, Inc. QUALCOMM is registered trademark of Qualcomm Incorporated. ATHEROS is a registered trademark of Qualcomm Atheros, Inc. Any other registered and unregistered trademarks are the property of Qualcomm Incorporated, Qualcomm Atheros, Inc. or their respective owners and used with permission. Registered marks owned by Qualcomm Incorporated and Qualcomm Atheros, Inc. are registered in the United States of America and may be registered in other countries. This technical data may be subject to U.S. and international export, re-export, or transfer (“export”) laws. Diversion contrary to U.S. and international law is strictly prohibited. Qualcomm Atheros, Inc. 1700 Technology Drive San Jose, CA 95110-1383 U.S.A. Copyright © 2011 Qualcomm Atheros, Inc. All rights reserved. QCASP141 Modular Certification OEM Integrator Instructions MKG-xxxxx Ver. 1.0 January 27, 2014 MKG-xxxxx Ver. 1.0 2 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION Revision history Revision Date Description Ver. 1.0 Nov. 11, 2013 Initial release Ver. 1.1 Jan 27, 2014 Updated separation distance for PIFA antenna per SAR report NOTE: The Qualcomm Atheros (QCA) design radio module (the “Module”) is designed for use only in specific countries in which QCA has obtained certificates of compliance with local laws and regulations. Therefore, the Module may not be sold, operated or incorporated into products for use in countries for which it has not been certified. See Section 3 herein. In addition, any deviation from the settings, methods, conditions and restrictions for integration of the Module into a host system, as detailed in this document, could be a violation of applicable national law and may be punishable as such, and in such event, the products into which the Module is incorporated may not be lawfully distributed or sold in such countries. QCA assumes no responsibility for any liability or loss related to installation, integration or operation of the Module. QCASP141 Modular Certification OEM Integrator Instructions MKG-xxxxx Ver. 1.0 3 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION Contents 1 Introduction ...................................................................................................... 4 2 Applicable Module ........................................................................................... 4 3 Available Global Modular Approvals from Qualcomm Atheros .................. 5 4 Additional Regulatory Conformance Testing and/or Submissions Required by the Integrator ........................................................................... 5 5 Compliant/Allowable Tx Power Settings Programmed into EEPROM ........ 7 6 Allowable Antennas For Use With The Radio Module .................................. 7 7 Antenna Placement inside the Host System and RF Safety ........................ 8 8 Simultaneous Transmission with Other Integrated or Plug-In Radios ....... 8 9 Module May Not Be Installed by End Users .................................................. 9 10 Required Labeling on the Outside of the Host .......................................... 10 10.1 FCC ........................................................................................................................... 10 10.2 Taiwan NCC ............................................................................................................. 10 10.3 European Community R&TTE ................................................................................. 11 11 Required Labeling on the Module .............................................................. 12 11.1 FCC labeling on the Module ..................................................................................... 12 11.2 Rest of world labeling on the Module ....................................................................... 12 11.3 Instructions to download the sample global label artwork with certification IDs .... 12 12 Required Regulatory Wording for User Manual/Installation Manual ....... 13 12.1 FCC compliance information .................................................................................... 13 12.2 Industry Canada notice ............................................................................................. 14 12.3 European Community (R&TTE) user manual wording and declaration .................. 15 12.4 European Community (R&TTE) Declaration of Conformity for System................. 17 12.5 Taiwan user manual wording .................................................................................... 17 12.6 Korea user manual wording ...................................................................................... 18 13 OEM Integrator Checklist ............................................................................ 19 QCASP141 Modular Certification OEM Integrator Instructions MKG-xxxxx Ver. 1.0 4 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION 1 Introduction This document describes the steps that the OEM integrator must follow when designing and manufacturing a system utilizing a Qualcomm Atheros (QCA) design radio module (the “Module”). Failure to follow the instructions in this document may invalidate the FCC certification and authorization of the Module for use in the U.S. and in other countries. The Qualcomm Atheros modular certifications described in this document apply only to radio conformance for the Module. The OEM integrator is responsible for all system-level EMI/EMC and Product Safety testing and certification that apply to the host system in the U.S. and other countries where the system will be marketed or …

Text truncated - open the document above for the full version.

FCC ID: PPD-QCASP141 Report No. : RF131022E03 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch January 22, 2014 Dear Application Examiner, Atheros Communications, Inc., It’s a 1x1 802.11b/g/n module, FCC ID: PPD-QCASP141, would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip QCA4002. 3. “The modular transmitter must have its own power supply regulation part no.: QCA4002. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration”. The EUT is tested in a stand-alone configuration via an extender. Please see section Photographs of Test Configuration in the test report. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

J QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 www.qualcomm.com September 16, 2013 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Authorization of Handling FCC Regulatory Applications FCC Identifier PPD To Whom It May Concern: I, hereby, authorize Caroline Yu, to handle FCC Regulatory related applications for QUALCOMM ATHEROS Incorporated FCC Identifier PPD and can sign all required application documents. Best Regards, Paul Guckian VP, Engineering Qualcomm Technologies, Inc. 5775 Morehouse Drive San Diego, CA 92121 Office: 858-651-1547 [email protected]

QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com Power of Attorney 2013/12/5 To whom it may concern: We, the undersigned Qualcomm Atheros, Inc. hereby authorize Bureau Veritas Consumer Product Service (Hong Kong) Limited, Taoyuan Branch of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15 approval and any communication needed with the national authority. Any and all acts carried out by BVCPS on our behalf shall have the same effects as acts of our own. This authorization is limited to the following products： FCC ID: PPD-QCASP141 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, --------------------------------------------------------------------------- Caroline Yu / Wireless Regulatory Project Manager

QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com Date:2013/12/6 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: PPD-QCASP141 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Theory of Operation Addendum - Regulatory algorithms Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Pursuant to DA 04-1705 of the Commission’s Rules, we request short-term confidential treatment for the following information until 180 days after the Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External Photos Internal Photos Test Setup Photos Integrator Instructions It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com --------------------------------------------------------------------------- Caroline Yu / Wireless Regulatory Project Manager

QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com 2014/2/7 To whom it may concern: With this letter, we confirm that the maximum compliant power level of SP141 module as listed on page 23 of report RF131022E03, as well as tested for modular SAR in report SA13122E03-1 module will not be exceeded in any case in any of our manufactured products. Sincerely yours, --------------------------------------------------------------------------- Caroline Yu / Wireless Regulatory Project Manager

Report No.: 131022E03 Page 1 CONSTRUCTION PHOTOS OF EUT Variant No.: SKU #1 (Thin) Report No.: 131022E03 Page 2 Variant No.: SKU #2 (SP141) Report No.: 131022E03 Page 3 Report No.: 131022E03 Page 4 Report No.: 131022E03 Page 5 Variant No.: SKU #1 (Thin) Report No.: 131022E03 Page 6 Variant No.: SKU #2 (SP141)

PROPOSED FCC ID LABEL AND LOCATION Printed Color： ：： ： Black 地色 地色地色 地色 ： ：： ：White 材質 材質材質 材質 ： ：： ：一般合成紙 一般合成紙一般合成紙 一般合成紙 粘著材 粘著材粘著材 粘著材 ： ：： ：樹脂系糊 樹脂系糊樹脂系糊 樹脂系糊 Bottom of EUT FCC / IC Label Location (on Shielding cover) QUALCOMM ATHEROS, INC. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: PPD-QCASP141 IC: 4104A-QCASP141 Model: QCASP141

Report No.: 131022E03 Page 1 CONSTRUCTION PHOTOS OF EUT Variant No.: SKU #1 (Thin) Report No.: 131022E03 Page 2 Variant No.: SKU #2 (SP141)

IC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 21 Report No. : SA131022E03-1 Issued Date : Jan. 22, 2014 Revision : R01 IC SAR Test Report Report No. : SA131022E03-1 Applicant : Qualcomm Atheros, Inc. Address : 1700 Technology Drive, San Jose, CA 95110 Product : 1x1 802.11b/g/n module IC : 4104A-QCASP141 Brand : Qualcomm Atheros Model No. : QCASP141 Standards : IC RSS-102 Issue 4:2010 / IEEE 1528:2013 / IEC 62209-2:2010 KDB 248227 D01 v01r02 / KDB 447498 D01 v05r01 Sample Received Date : Oct. 22, 2013 Date of Testing : Jan. 17, 2014 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Gordon Lin / Assistant Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. IC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 21 Report No. : SA131022E03-1 Issued Date : Jan. 22, 2014 Revision : R01 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 12 3.4 SAR Measurement Procedure ................................................................................................................................... 13 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 13 3.4.2 Volume Scan Procedure................................................................................................................................... 13 3.4.3 Power Drift Monitoring ...................................................................................................................................... 14 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 14 3.4.5 SAR Averaged Methods ...................................................…

Text truncated - open the document above for the full version.

Report No.: SA131022E03 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA131022E03 MODEL NO.: QCASP141 FCC ID: PPD-QCASP141 IC: 4104A-QCASP141 RECEIVED: Oct. 22, 2013 TESTED: Dec. 02, 2013 ISSUED: Jan. 09, 2014 APPLICANT: Qualcomm Atheros, Inc. ADDRESS: 1700 Technology Drive, San Jose, CA 95110 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA131022E03 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. ANTENNA GAIN....................................................................................................... 5 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA131022E03 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA131022E03 Original release Jan. 09, 2014 Report No.: SA131022E03 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: 1x1 802.11b/g/n module BRAND NAME: Qualcomm Atheros MODEL NO.: QCASP141 TEST SAMPLE: R&D SAMPLE APPLICANT: Qualcomm Atheros, Inc. STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: QCASP141) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Jan. 09, 2014 ( Phoenix Huang, Specialist ) APPROVED BY : , DATE: Jan. 09, 2014 ( May Chen, Manager ) Report No.: SA131022E03 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 5. ANTENNA GAIN The declared antenna gain is 3.62dBi. this antenna gain was used for conducted spurious/bandedge calculations. Report No.: SA131022E03 6 of 6 Report Format Version 5.0.0 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER 802.11b FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 188.365 3.62 20 0.08624 1.00 802.11g FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 456.037 3.62 20 0.20880 1.00 802.11n (HT20) FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 448.745 3.62 20 0.20546 1.00 802.11n (HT40) FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2422-2452 153.109 3.62 20 0.07010 1.00 --- END --- CONCLUSION: Both of the WLAN and Bluetooth can transmit simultaneously, the formula of calculated the MPE is: CPD 1 / LPD 1 + CPD 2 / LPD 2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density Therefore, the worst-case situation is 0.21630 / 1 + 0.00275 / 1= 0.219, which is less than “1”. This confirmed that the device comply with FCC 1.1310 MPE limit.

Report No.: RF131022E03 1 of 90 Report Format Version 5.2.0 Cancels and replaces the report No.: RF120720E01 R1 dated: May 03, 2012 FCC TEST REPORT (15.247) REPORT NO.: RF131022E03 MODEL NO.: QCASP141 FCC ID: PPD-QCASP141 IC: 4104A-QCASP141 RECEIVED: Oct. 22, 2013 TESTED: Nov. 06 to Dec. 19, 2013 ISSUED: Jan. 09, 2014 APPLICANT: Qualcomm Atheros, Inc. ADDRESS: 1700 Technology Drive, San Jose, CA 95110 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF131022E03 2 of 90 Report Format Version 5.2.0 Cancels and replaces the report No.: RF120720E01 R1 dated: May 03, 2012 Table of Contents RELEASE CONTROL RECORD ............................................................................................ 5 1. CERTIFICATION ....................................................................................................... 6 2. SUMMARY OF TEST RESULTS ............................................................................... 7 2.1 MEASUREMENT UNCERTAINTY ....................................................................8 3. GENERAL INFORMATION ........................................................................................ 9 3.1 GENERAL DESCRIPTION OF EUT .................................................................9 3.2 DESCRIPTION OF ANTENNA ....................................................................... 11 3.3 DESCRIPTION OF TEST MODES .................................................................12 3.3.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ..............13 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .................................16 3.5 DUTY CYCLE OF TEST SIGNAL ...................................................................17 3.6 DESCRIPTION OF SUPPORT UNITS ...........................................................18 3.7 CONFIGURATION OF SYSTEM UNDER TEST .............................................18 4. TEST TYPES AND RESULTS ................................................................................. 19 4.1 CONDUCTED OUTPUT POWER MEASUREMENT ......................................19 4.1.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT......................19 4.1.2 INSTRUMENTS ..........................................................................................19 4.1.3 TEST PROCEDURES .................................................................................19 4.1.4 DEVIATION FROM TEST STANDARD .......................................................19 4.1.5 TEST SETUP ..............................................................................................19 4.1.6 EUT OPERATING CONDITIONS ................................................................20 4.1.7 TEST RESULTS ..........................................................................................21 4.2 AVERAGE OUTPUT POWER .........................................................................22 4.2.1 FOR REFERENCE......................................................................................22 4.2.2 TEST INSTRUMENTS ......................................................................…

Text truncated - open the document above for the full version.