PPD-WCN3660802.11a/b/g/n + USB BT 4.0 card

Qualcomm Atheros 802.11n Adapter Model WCN3660 February 29, 2012 © 2000–2009 by Qualcomm Atheros Communications, Inc. All rights reserved. Qualcomm Atheros ® , Qualcomm Atheros Driven ® , Qualcomm Atheros XR ® , Driving the Wireless Future ® , ROCm ® , Super AG ® , Super G ® , Total 802.11n ® , and Wake on Wireless ® are registered by Qualcomm Atheros Communications, Inc. Qualcomm Atheros SST™, Signal-Sustain Technology™, the Air is Cleaner at 5-GHz™, XSPAN™, Wireless Future. Unleashed Now.™, and 5-UP™ are trademarks of Qualcomm Atheros Communications, Inc. The Qualcomm Atheros logo is a registered trademark of Qualcomm Atheros Communications, Inc. All other trademarks are the property of their respective holders. Notice The information in this document has been carefully reviewed and is believed to be accurate. Nonetheless, this document is subject to change without notice, and Qualcomm Atheros Communications, Inc. (Qualcomm Atheros) assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the contained information, or to notify a person or organization of any updates. Qualcomm Atheros reserves the right to make changes, at any time, in order to improve reliability, function or design and to attempt to supply the best product possible. Qualcomm Atheros does not represent that products described herein are free from patent infringement or from any other third party right. No part of this document may be reproduced, adapted or transmitted in any form or by any means, electronic or mechanical, for any purpose, except as expressly set forth in a written agreement signed by Qualcomm Atheros. Qualcomm Atheros or its affiliates may have patents or pending patent applications, trademarks, copyrights, maskwork rights or other intellectual property rights that apply to the ideas, material and information expressed herein. No license to such rights is provided except as expressly set forth in a written agreement signed by Qualcomm Atheros. QUALCOMM ATHEROS MAKES NO WARRANTIES OF ANY KIND WITH REGARD TO THE CONTENT OF THIS DOCUMENT. IN NO EVENT SHALL QUALCOMM ATHEROS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL SPECULATORY OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. IN PARTICULAR, QUALCOMM ATHEROS SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA TRANSMITTED OR OTHERWISE USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE OR DATA. QUALCOMM ATHEROS SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE AS THEY MIGHT OTHERWISE APPLY TO THIS DOCUMENT AND TO THE IDEAS, MATERIAL AND INFORMATION EXPRESSED HEREIN. Qualcomm Atheros, Inc. • 3 COMPANY CONFIDENTIAL February 2012 Document Conventions Text Conventions bold Bold type within paragraph text indicates commands, file names, directory names, paths, output, or returned values. Example: The DK_Client package will not function unless you use the wdreg_install batch file. italic Within commands, italics indicate a variable that the user must specify. Example: mem_alloc size_in_bytes Titles of manuals or other published documents are also set in italics. Courier The Courier font indicates output or display. Example: Error:Unable to allocate memory for transfer! Menu The Menu character tag is used for menu items. Example: Choose Edit > Copy. [ ] Within commands, items enclosed in square brackets are optional parameters or values that the user can choose to specify or omit. { } Within commands, items enclosed in braces are options from which the user must choose. | Within commands, the vertical bar separates options. ... An ellipsis indicates a repetition of the preceding parameter. > The right angle bracket separates successive menu selections. Example: Start > Programs > DK > wdreg_install. Notices NOTE: This message denotes neutral or positive information that calls out important points to the text. A note provides information that may apply only in special cases. 4 • Qualcomm Atheros, Inc. COMPANY CONFIDENTIAL Contents Introduction ............................................................................................................... 7 System Requirements ........................................................................................ 7 Profile Management ................................................................................................. 7 Create or Modify a Configuration Profile ...................................................... 7 Remove a Configuration Profile ...................................................................... 8 Auto Profile Selection Management ....................................................................... 8 Switching to a Different Configuration Profile ..................................................... 9 Import and Export Profiles ....................................................................................... 9 Importing a Profile ..................................................................................................... 9 Exporting a Profile ..................................................................................................... 9 TCP/IP Configuration ............................................................................................. 9 Configuring the TCP/IP Address for the network device: ................................... 9 General Tab .............................................................................................................. 10 Advanced Tab ......................................................................................................... 10 Security Tab ............................................................................................................. 11 Using EAP-TLS Security ..…

Text truncated - open the document above for the full version.

Attestation We attest regarding Bluetooth AFH mode for the WCN3660 Module: a. The minimum number of hopping channel in AFH mode is 20. b. The output power does not exceed 125 mW. c. The channel separation is based on 2/3 of the 20 dB channel bandwidth. This model is compliant with theBluetooth Core Spec V4/0+HS. Regards, Michael Green Manager, Global Product Compliance

QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by CCS on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Michael Green / Manager, Global Product Compliance Qualcomm Atheros, Inc. REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

J QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 www.qualcomm.com June 15, 2011 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Authorization of Handling FCC Regulatory Applications To Whom It May Concern: I, hereby, authorize Mr. Michael Green, to handle FCC Regulatory related applications for QUALCOMM ATHEROS Incorporated and sign all required application documents. Best Regards, Paul Guckian VP, Engineering QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121 Office: 858-651-1547 [email protected]

QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 qca.qualcomm.com June 4, 2012 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality, FCC ID: PPD-WCN3660 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Theory of Operation Addendum - Regulatory algorithms Integrator Instructions Above mentioned document contains detailed system and equipment descriptions considered as proprietary information. The public disclosure of above documents might be harmful to our company and would give competitors an unfair advantage in the market. Pursuant to DA 04-1705 of the Commission’s Rules, we request short-term confidential treatment for the following information for 180 days in order to ensure sensitive business information remains confidential until the marketing of the device: External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Regards, --------------------------------------------------------------------------- Michael Green / Manager, Global Product Compliance

QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 1 qca.qualcomm.com June 7, 2012 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Road Columbia, MD 21046-1609 Subject: Request for Modular Approval FCC ID: PPD-WCN3660 Qualcomm Atheros respectfully requests that the WCN3660 802.11n + BT Adapter be certified as a Limited Split-Module per the provisions of FCC Rule Section 15.212 and OET Knowledge Database (KDB) Number 996369 D01 Module Certification Guide v01r03. The device meets each of the applicable requirements in Rule Section 15.212(a)(1) and (a)(2), as detailed below: General Module Requirements of Section 15.212(a)(1) i. The radio elements must have the radio frequency circuitry shielded; WCN3660 includes an RF shield. Please refer to the photos associated with the application. ii. The module must have buffered modulation/data inputs; WCN3660 has buffered modulation/data inputs. This is ensured by the host processor. iii. The module must contain power supply regulation on the module; WCN3660 includes an LDO voltage regulator on board. iv. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); Host systems using WCN3660 will include a unique antenna connector. This is made clear in the Integrator Instructions provided by Qualcomm Atheros QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 2 qca.qualcomm.com v. The module must demonstrate compliance in a stand-alone configuration; WCN3660 was tested in a stand-alone configuration and demonstrated compliance. Please refer to the test report, including the test setup photos. vi. The module must be labeled with its permanently affixed FCC ID label; WCN366 will have an FCC ID label permanently affixed per the submitted labeling exhibit. vii. The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; Qualcomm Atheros will advise, assist and monitor the activities of each system integrator to ensure that their end systems comply with the FCC’s Part 15 rules. The process that Qualcomm Atheros will follow is well documented in the Integrator Instructions. viii. The module must comply with RF exposure requirements (see discussions below); The module complies with FCC RF exposure requirements as a Mobile category device as documented in the submitted test reports. In addition, the grantee will ensure that each host system undergoes applicable RF evaluation and permissive change submission, including evaluation of all colocated radios, as applicable. QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 3 qca.qualcomm.com Additional Split-Module Requirements of Section 15.212(a)(2) i. Only the radio front-end must be shielded. The interface between the split sections of the modular system must be digital, with a minimum signaling amplitude of 150 mV peak-to-peak; The radio front end (WCN3660) is shielded as noted above. The interface between the split sections is comprised of: - Digital lines between the radio front end and host processor which control radio functions AND - Two differential pair, analog I/Q lines which send/receive baseband data between the radio front end and host processor. The signaling amplitude of these lines is less than 150mV peak-to-peak. Since an alternative to this clause has been implemented, Limited Split-Modular approval is applicable and compliance of host systems with Part 15 rules will be ensured as documented in the Integrator Instructions. ii. Control information and other data may be exchanged between the transmitter control elements and radio front-end; As detailed in item (i) directly above, the interface between the radio front end and host processor includes I/Q baseband data and control signaling. iii. The sections of a split-modular transmitter are installed for testing on a host platform that is representative of the platform(s) intended for use. It is the responsibility of the applicant to demonstrate the appropriateness of the test platform for compliance to a widespread range of common host platforms, i.e. not restricted to a specific host. For example, compliance may be demonstrated on an open (not within a specific host enclosure) reference design board to demonstrate conformity independent of the host environment. Therefore, note that when compliance is tested with the module enclosed in a specific host, then the split module must be limited; The WCN3660 was tested in a standalone configuration (outside of a host) to demonstrate conformity independent of the host environment. In addition, each host system will be tested for compliance with Part 15 radiated emissions as described in the Integrator Instructions. QUALCOMM ATHEROS, INC. 1700 Technology Drive, San Jose, CA 95110 T 408.773.5200 | F 408-773-9940 4 qca.qualcomm.com iv. The radio front-end and transmitter control element must be certified as amalgamated elements by the responsible party. The responsible party must demonstrate the authentication method to guarantee that only this coupling will operate the radio. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization; The WCN3660 split module is designed to operate using only Qualcomm host processors. Proprietary microcode and architecture makes it impossible for non- Qualcomm processors to function with the WCN3660 radio front end. Qualcomm Atheros only offers for sale the WCN3660 and host processors pursuant to a license agreement with a limited number of customers/inte…

Text truncated - open the document above for the full version.

1 From: Claire Hoque, Compliance Certification Services, [email protected] To: Andrew Leimer, [email protected] Re: FCC ID: PPD-WCN3660 Applicant: Qualcomm Atheros, Inc. Correspondence Reference Number: 42490 Form 731 Confirmation Number: EA131686 Date of Original E-mail: 08/17/2012 1) Submit the Block Diagram exhibit and the Schematics exhibit. <answer> Block Diagram exhibit and Schematics exhibit are uploaded to FCC site on Aug.17, 2012. Operational Description exhibit also uploaded. Thanks, UL CCS

WCN3660 Top w/shield WCN3660 Bottom

PROPOSED MODULE LABEL PPD-WCN3660 - Label sticker affixed to top of Module FCC ID: PPD-WCN3660 Qualcomm Atheros Model WCN3660

UUT Photos PPD-WCN3660 WCN3660 Top

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR 802.11n + BT MODULE MODEL NUMBER: WCN3660 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 REPORT NUMBER: 12U14222-9 ISSUE DATE: JUNE 11, 2012 Prepared for QUALCOMM ATHEROS, INC 1700 TECHNOLOGY DRIVE SAN JOSE, CA 95110 U.S.A. Prepared by COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 2 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Revision History Rev. Issue Date Revisions Revised By -- 06/11/12 Initial Issue F. Ibrahim REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 3 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS .................................................................................... 5 2. TEST METHODOLOGY ........................................................................................................ 6 3. FACILITIES AND ACCREDITATION .................................................................................... 6 4. CALIBRATION AND UNCERTAINTY .................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ................................................................ 6 4.2. SAMPLE CALCULATION ............................................................................................... 6 4.3. MEASUREMENT UNCERTAINTY ................................................................................. 6 5. EQUIPMENT UNDER TEST ................................................................................................. 7 5.1. DESCRIPTION OF EUT ................................................................................................. 7 5.2. MODIFICATIONS ........................................................................................................... 7 5.3. MAXIMUM OUTPUT POWER ........................................................................................ 7 5.4. DESCRIPTION OF AVAILABLE ANTENNAS ................................................................ 7 5.5. SOFTWARE AND FIRMWARE ...................................................................................... 7 5.6. WORST-CASE CONFIGURATION AND MODE ............................................................ 8 5.7. DESCRIPTION OF TEST SETUP .................................................................................. 9 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 11 7. ANTENNA PORT TEST RESULTS .................................................................................... 12 7.1. BASIC DATA RATE GFSK MODULATION .................................................................. 12 7.1.1. 20 dB AND 99% BANDWIDTH ............................................................................. 12 7.1.2. HOPPING FREQUENCY SEPARATION .............................................................. 19 7.1.3. NUMBER OF HOPPING CHANNELS ................................................................... 21 7.1.4. AVERAGE TIME OF OCCUPANCY ..................................................................... 26 7.1.5. OUTPUT POWER ................................................................................................. 33 7.1.6. AVERAGE POWER .............................................................................................. 37 7.1.7. CONDUCTED SPURIOUS EMISSIONS ............................................................... 38 7.2. ENHANCED DATA RATE 8PSK MODULATION ......................................................... 47 7.2.1. 20 dB AND 99% BANDWIDTH ............................................................................. 47 7.2.2. HOPPING FREQUENCY SEPARATION .............................................................. 54 7.2.3. NUMBER OF HOPPING CHANNELS ................................................................... 56 7.2.4. AVERAGE TIME OF OCCUPANCY ..................................................................... 61 7.2.5. OUTPUT POWER ................................................................................................. 68 7.2.6. AVERAGE POWER .............................................................................................. 72 7.2.7. CONDUCTED SPURIOUS EMISSIONS ............................................................... 73 8. RADIATED TEST RESULTS .............................................................................................. 82 8.1. LIMITS AND PROCEDURE ......................................................................................... 82 8.2. TRANSMITTER ABOVE 1 GHz ................................................................................... 83 8.2.1. BASIC DATA RATE GFSK MODULATION ........................................................... 83 REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 4 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 8.2.2. ENHANCED DATA RATE 8PSK MODULATION .................................................. 92 9. AC POWER LINE CONDUCTED EMISSIONS ................................................................. 101 10. MAXIMUM PERMISSIBLE EXPOSURE ......................…

Text truncated - open the document above for the full version.

REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 110 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 11. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 111 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION X-AXIS FRONT PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 112 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. X-AXIS BACK PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 113 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Y-AXIS FRONT PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 114 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Y-AXIS BACK PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 115 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Z-AXIS FRONT PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 116 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Z-AXIS BACK PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 117 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO REPORT NO: 12U14222-9 DATE: JUNE 11, 2012 FCC ID: PPD-WCN3660 IC: 4104A-WCN3660 Page 118 of 118 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701D 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. END OF REPORT LINE CONDUCTED BACK PHOTO