PQCM4842AIntelliVue Access Point

Instructions for Use IntelliVue TRx/TRx + Transceivers for the Philips IntelliVue Telemetry System with Smart-Hopping Technology Part Number: M4841-91001 Printed in the U.S.A. November 2004 First Edition Notice Operation of this equipment in the United States re- quires the prior coordindation with a frequency coor- dinator designated by the Federal Communications Commission (FCC) for the Wireless Medical Teleme- try Service. Printing History ii NoticeEquipment specifications are subject to alteration without notice. All changes will be in compliance with regulations governing manufacture of medical equipment. Printed in the USA. Document number: M4841-91001 © Copyright 2004 Koninklijke Philips Electronics N.V. All Rights Reserved. OxiCliq and OxiMax are registered trademarks of Nellcor® Incorporated. Printing History New editions of this document will incorporate all material updated since the previous edition. Update packages can be issued between editions and contain replacement and additional pages to be merged by a revision date at the bottom of the page. Note that pages which are rearranged due to changes on a previous page are not considered revised. The documentation printing date and part number indicate its current edition. The printing date changes when a new edition is printed. (Minor corrections and updates which are incorporated at reprint do not cause the date to change.) The document part number changes when extensive technical changes are incorporated. First Edition ...............................................................................November 2004 Philips IntelliVue Telemetry System with Smart Hopping Technology is compatible with: Philips Information Center, software revision F.00 Philips TeleMon Companion Monitor, #A02/A03 About this Book iii About this Book This book contains operating instructions for use of the IntelliVue TRx and TRx + Transceivers as used with the Philips IntelliVue Telemetry System with Smart-hopping Technology. It also includes operational information for the Telemetry functions of the IntelliVue Information Center. The intended audience is the clinician who uses and/or teaches others to use the equipment in a healthcare environment. For operating information on other functionality of the Information Center, see IntelliVue Information Center Instructions for Use. For preventive maintenance, repair, and test methods for verification of device performance, refer to the Philips IntelliVue Telemetry System Service Kit. This book does not address the Philips M2601B Transmitter or the M2600B Philips Telemetry System. For information on those products, refer to the manual Philips Telemetry System Instructions for Use. Note—Use this product in conjunction with Philips IntelliVue Information Center Instructions for Use and Online Help, and with Philips TeleMon A02/ A03 Companion Monitor Instructions for Use. See also the Philips IntelliVue Telemetry Training Program. Document Conventions Warnings WarningWarning Warnings are information you should know to avoid injuring patients and personnel. Cautions Caution Cautions are information you should know to avoid damaging your equipment and software. Product Safety Information iv Notes Note—Notes contain additional information on use of the Philips IntelliVue Telemetry System. Procedures Procedures are indicated in text by the heading “Task Summary” followed by the following table: Bold Typeface Objects of actions in procedures appear in bold typeface. Note the following example: Select the Standby button. Product Safety Information The following general warnings and cautions apply to use of the Philips IntelliVue Transceivers in a Philips IntelliVue Wireless Network. Additional warnings and cautions specific to a particular feature are provided in the appropriate section. General WarningWarning For continued safe use of this equipment, it is necessary that the listed instructions are followed. Instructions in this manual in no way supersede established medical procedures. Step Action 1 2 3 Product Safety Information v WarningWarning Do not touch the patient, or table, or instruments, during defibrillation. The battery door must be closed during defibrillation. These steps protect the clinician from high defibrillator voltage. WarningWarning This device is not to be used in the vicinity of electrosurgical units because use may interrupt or interfere with the transmission of signals from the transceiver. WarningWarning This equipment is not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide WarningWarning Do not use patient cables with detachable lead wires that have exposed male pins. Electrocution could result if these pins are plugged into AC power. WarningWarning Use of product accessories (e.g., ECG leadsets, SpO 2 sensors) other than those prescribed by Philips could lead to patient injury. WarningWarning To avoid strangulation, do not tie a pouch solely around the patient’s neck. Product Safety Information vi ECG/ Arrhythmia - All Patients WarningWarning ECG SAFETY FOR ALL PATIENTS Always confirm Information Center observations with clinical observation of the patient before administering interventions. Every lead must be secured to an electrode on the patient. Conductive parts of electrodes must not contact earth or other conductive parts. Philips recommends that you change the lead label only to reflect the physical placement of electrodes. This will ensure a match between the monitored lead and the label, and prevent any possible confusion. When switching between EASI and standard monitoring, there is a loss of data for 30 seconds. Product Safety Information vii WarningWarning ST/AR ARRHYTHMIA SAFETY FOR ALL PATIENTS During complete heart block or pacemaker failure (to pace or capture), tall P-waves (greater than 1/5 of the average R-wave height) can be erroneously counted by the arrhythmia algorithm, resulting in missed detection of c…

Text truncated - open the document above for the full version.

Philips Medical Systems To: Date: From: Subject: Federal Communications Commission, Washington, DC 20554 August 25, 2004 Barry Wyshogrod, Philips Medical Systems. Andover, MA Application for Radio Grant and associated Request for Confidentiality Dear Sir or Madam, Philips Medica! Systems of Andover, Massachusetts hereby submits the enclosed application for Equipment Authorization under 47 CFR Part 95, Subpart H for a wireless medical telemetry station transmitter, Model M4842A. Upon receipt of this grant, the grant 10 number will be applied to the device. Furthermore, the instruction to the user concerning frequency coordination (as per 47 CFR 95.1109) will appear on the product label. This filinq includes: 1. Block Diagram & Functional Description 2. Schematics 3. Bill of Material 4. Internal Exploded View 5. Part 95 Test Report Under the provisions of Section O.457(d) of the Commission's Rules, and Section 552(b)(4) of the Freedom of Information Act, Philips Medical Systems hereby requests that items 1-5 listed above be granted Indefinite Confidentiality from public disclosure, as this information is deemed to represent trade secrets. In addition. this filina also includes: 6. Artwork for Product Labels 7. External Device Photographs Under the provisions of FCC Public Notice DA 04-1705, dated 15-Jun-04, Philips Medical Systems hereby requests that items 6 & 7 listed above be granted 45-day limited Confidentiality from public disclosure, as the information is deemed to represent commercial secrets. If for some reason, the Commission cannot provide the Indefinite and limited Confidentialities as requested above, please contact me, and please insure that no material is placed into the public domain until we have had a chance to discuss this issue. Thank you in advance for your consideration of this application. I can be reached at (978) 659- 7383 or bye-mail to: [email protected]. If I am not available, please contact Ms. Denise Haley at (978) 659-4358 or bye-mail to: [email protected]. Sincerely yours, , ~~~'44-'?/J,C~' - - - Regulatory Engineer 3000 Minuteman Road Andover, Massachusetts 01810 Tel: (978) 687 150 I, Fax: (978) 794 7646 www.philips.com Ie

To: Date: From: Subject: Federal Communications Commission, Washington, DC 20554 Attention: Ms. Linda Elliot September 14, 2004 Barry Wyshogrod, Philips Medical Systems, Andover, MA Reply to Correspondence Reference #27578 731 Application #EA408759 Dear Ms. Elliot and FCC Reviewers, On 13-Sep-O4. vou e-mailed me the followinq observation: The FCC ID (PQCM4842A) entered on the Form 731, does not agree with the FCC ID (PQCM6000-95A) displayed on the proposed labeling. Submit an email/letter to correct the FCC ID on the Form 731, or a revised identification label, as appropriate. PhiliDS Medical Systems' reSDonse: You are correct, and I apologize for my oversight. The FCC 10 number shown on the previously submitted product label artwork, and on the accompanying product photo, shows a fictitious 10 which was only meant as a placeholder (PQCM6000-95A) for our industrial design group. This is not the intended FCC 10 number. The FCC 10 will be PQCM4842A. I hereby attach two new attachments to our EA408759 submission: 1. 2. Revised artwork for the M4842A product label. A revised photograph of the M4842A product, with handwritten correction attesting to the intended "PQCM4842A" FCC 10 label. Under the provisions of FCC Public Notice DA 04-1705, dated 15-Jun-04, Philips Medical Systems hereby requests that these two items be granted 45-day limited Confidentiality from public disclosure, as the information is deemed to represent commercial secrets. Thank you in advance for your continued consideration of our application, and my regrets for any confusion caused. For any further issues, I can be reached at (978) 659-7383 or bye-mail to: [email protected]. If I am not available, please contact Ms. Denise Haley at (978) 659-4358 or bye-mail to: [email protected]. Sincerely yours, ~ 1f7 { Barry ZOgrOd Requlatory Enqineer

Page 1 of 2 To: Federal Communications Commission, Washington, DC 20554 Attention: Ms. Diane Poole Date: October 19, 2004 From: Barry Wyshogrod, Philips Medical Systems, Andover, MA Subject: Reply to Correspondences, References #27751, #27752, #27753 731 Application #EA408759 Dear Ms. Poole and FCC Reviewers, On 5-Oct-04, you e-mailed me the following observations/requests: 1. Please resubmit the confidentiality request letter. Note that the Part 95 Test Report exhibit can not be held confidential. 2. You have requested the Internal Exploded View to be confidential. Please explain how you prevent the public from seeing the inside of the equipment (any special tool to open the device), and give a special justification why we have to keep it confidential. 3. Please submit a formal special 45 days confidentiality request letter specifying those exhibits you wish to have held confidential (For example: User manual, external photos...). Note that the revised Artwork for the M4842A Product Label exhibits can not be held confidential. Philips Medical Systems’ response to Item #1 above: With appreciation to you, Diane, for helping me over the phone last week, I hereby attach a new Request for Confidentiality. This request consists of two parts; a request for Indefinite Confidentiality for certain deliverables, and second, a request for 45-day Limited Confidentiality for other submitted items. I understand that the Part 95 Test Report cannot be granted either type of confidentiality, and it no longer appears as part of the Request for Confidentiality. This Request for Confidentiality supercedes my initial requests (Cover Letter, and Cover Letter– Request for Confidentiality) dated 25-Aug-04. Philips Medical Systems’ response to Item #2 above: Philips is no longer requesting Indefinite Confidentiality for the Internal Exploded View; only 45- day Limited Confidentiality, as listed in the attached, new Request for Confidentiality. Limited Confidentiality is important for Philips Medical Systems from a commercial perspective. It enables the company to complete its development and regulatory efforts prior to introducing the product to the marketplace. Releasing information on the product via the FCC website prior to formal market introduction can be confusing to our customers and to the medical community, and places the company at a competitive disadvantage. Philips Medical Systems’ response to Item #3 above: I hereby attach the revised Request for Confidentiality, which includes the appropriate section on 45-day Limited Confidentiality. As agreed with you, Diane, Philips Medical Systems will request the 45-day protection for the Internal Exploded View and External Photographs, and for the Instructions for Use, but not for the FCC ID Label. Philips Medical Systems Page 2 of 2 Therefore, I hereby attach two new attachments to our EA408759 submission: 1. Revised Request for Confidentiality. 2. Revised FCC ID label artwork showing relevant FCC labeling and placement. It is understood that this will not be held confidential. Please delete the previous attachment submitted for the FCC ID Label. Diane, thank you in advance for all your help and patience; it is much appreciated. For any further issues, I can be reached at (978) 659-7383 or by e-mail to: [email protected] . If I am not available, please contact Ms. Denise Haley at (978) 659-4358 or by e-mail to: [email protected]. Sincerely yours, Barry Wyshogrod, Regulatory Engineer Signature already on-file at the FCC

To: Federal Communications Commission, Washington, DC 20554 Date: October 19, 2004 From: Barry Wyshogrod, Philips Medical Systems, Andover, MA Subject: Application for Radio Grant for M4842A, 731 Confirmation Number: EA408759 REVISED REQUEST FOR CONFIDENTIALITY – Replaces 25-Aug-04 version Dear Sir or Madam, Philips Medical Systems has submitted an application for Equipment Authorization under 47 CFR Part 95, Subpart H for a wireless medical telemetry station transmitter, Model M4842A. The filing includes: 1. Block Diagram 2. Functional Description 3. Schematics 4. Bill of Material 5. Internal Exploded View 6. External Device Photograph 7. Instructions for Use 8. Part 95 Test Report 9. FCC ID Label Under the provisions of Section 0.457(d) of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act, Philips Medical Systems hereby requests that items 1-4 listed above be granted Indefinite Confidentiality from public disclosure, as this information is deemed to represent trade secrets: Under the provisions of FCC Public Notice DA 04-1705, dated 15-Jun-04, Philips Medical Systems hereby requests that items 5-7 listed above be granted 45-day Limited Confidentiality from public disclosure. Limited Confidentiality is important for Philips Medical Systems from a commercial perspective. It enables the company to complete its development and regulatory efforts prior to introducing the product to the marketplace. Releasing information on the product via the FCC website prior to formal market introduction can be confusing to our customers and to the medical community, and places the company at a competitive disadvantage. To summarize: Indefinite Confidentiality 45-day Limited Confidentiality No Confidentiality Block Diagram Internal Exploded View Part 95 Test Report Functional Description External Device Photograph FCC ID Label Schematics Instructions for Use Bill of Material Thank you in advance for your consideration of this application. I can be reached at (978) 659- 7383 or by e-mail to: [email protected] . If I am not available, please contact Ms. Denise Haley at (978) 659-4358 or by e-mail to: [email protected]. Sincerely yours, Barry Wyshogrod, Regulatory Engineer Signature already on-file at the FCC Philips Medical Systems

Page 1 of 1 To: Federal Communications Commission, Washington, DC 20554 Attention: Ms. Diane Poole Date: October 19, 2004 From: Barry Wyshogrod, Philips Medical Systems, Andover, MA Subject: Reply to Correspondences, References #27768, #27769, #27770 731 Application #EA408759 Dear Ms. Poole and FCC Reviewers, On 6-Oct-04, you e-mailed me the following observations/requests: The revised photograph of the M4842A product, with handwritten correction exhibit cannot be held confidential. Philips Medical Systems’ response: The photograph to which you refer was the attachment which I submitted on 14-Sep-04, as part of my reply to Ms. Linda Elliott and correspondence #27578. This photograph was meant to display the FCC ID Label for the device. However, in view of our phone conversation of last week, Diane, please permit me to make the following changes: 1. I hereby attach a revised FCC ID Label. Please delete the above-mentioned photograph and replace it with this new artwork. Diane, please note that this new artwork is identical to the FCC ID Label which I attached to a second reply to you of earlier today, namely, Philips Medical Systems’ response to correspondences #27751, #27752, and #27753. If you have already processed the FCC ID Label from my earlier reply, you can ignore this attachment; it’s the same. 2. Philips Medical Systems understands and agrees that this revised FCC ID Label will not be confidential. Diane, thank you for all your help. For any further issues, I can be reached at (978) 659-7383 or by e-mail to: [email protected] . If I am not available, please contact Ms. Denise Haley at (978) 659-4358 or by e-mail to: [email protected]. Sincerely yours, Barry Wyshogrod, Regulatory Engineer Signature already on-file at the FCC Philips Medical Systems

Page 1 of 1 To: Federal Communications Commission, Washington, DC 20554 Attention: Ms. Diane Poole Date: October 25, 2004 From: Barry Wyshogrod, Philips Medical Systems, Andover, MA Subject: Reply to Correspondences, References #27853, #27854 731 Application #EA408759 Dear Ms. Poole and FCC Reviewers, On 22-Oct-04, you e-mailed me the following request: Please add the FCC statement on the label as in 15.19 (a) of the FCC rules to the product. Philips Medical Systems’ response: I apologize for my oversight and will implement your request. We have added the appropriate text to the product’s FCC ID Labeling, as per my phone conversation with you, Diane. We will add the text as per 47 CFR Part 15.19(a)(1): “This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.” I hereby attach a revised FCC ID Label for the device. This attachment supercedes the previous label submitted on 19-Oct-04 as part of my reply to correspondences #27768, #27769, #27770. Diane, thank you for your help. For any further issues, I can be reached at (978) 659-7383 or by e-mail to: [email protected] . If I am not available, please contact Ms. Denise Haley at (978) 659-4358 or by e-mail to: [email protected]. Sincerely yours, Barry Wyshogrod, Regulatory Engineer Signature already on-file at the FCC Philips Medical Systems

P

RF Radio Module PC Assembly Philips M4842A (Station Transmitter)

TEST NUMBER - 296-04 TEST REPORT TO FEDERAL COMMUNICATIONS COMMISSION CFR47 PART95 Low Power Licensed Radio communication Devices Medical Telemetry II Service Transceiver In the bands 1395-1400 and 1427-14232 MHz for Philips Medical Systems Cardiac and Monitoring Systems 3000 Minuteman Drive Andover, MA 01810 978-659-2800 of Telemetry II Access Point Transceiver Model M4842A on 8/2/2004 Tested bv - S'9ned OY"1jlro\S on- tl\L 0.+ 'Phll,ps Med,cQI S~siLms Andrew Mertinooke Reviewed by 25 - Au;- 0-1'\ BrickClifton P This report may not be duplicated, except in full without written permission from Compliance Worldwide, Inc. Compliance Worldwide, Inc. - 357 Main Street - Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com Page 2 of 39 Compliance Worldwide, Inc. – 357 Main Street – Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com TEST NUMBER - 296-04 TABLE OF CONTENTS • Test Description • Test Results and Conclusions • Test Procedures • Part 95 Test Limits • Test Facility Description • Test Setup and Connection Information • Test Measurements and Results Radiated Measurements Radiated Output Power & Occupied Bandwidth Conducted Measurements • Notes and Comments Page 3 of 39 Compliance Worldwide, Inc. – 357 Main Street – Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com TEST NUMBER - 296-04 TEST DESCRIPTION 1. TEST OBJECTIVE To test the Telemetry II Access Point Transceiver Model M4842A to FCC Part 95 Rules and write a report. 2. E.U.T. DESCRIPTION GENERAL The Telemetry II Access Point transceiver is an RF link, normally mounted on a ceiling, that provides the connection between the Patient worn device transceiver and the monitoring station. FREQUENCIES USED: 1395.9, 1397.5, 1399.1, 1427.9, 1429.5, 1431.1 MHz MODULATION SCHEME: FSK with Root Raised Cosine Filtering SERIAL NUMBERS: US42200094 Page 4 of 39 Compliance Worldwide, Inc. – 357 Main Street – Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com TEST NUMBER - 296-04 TEST RESULTS AND CONCLUSIONS Rule Section Requirement Notes Pass Fail 95.1109(b) Labeling See Exhibits FCC Label Sample and Label Location. 1 95.115(a)(2) Field Strength Limits X 95.115(b) Undesired Emissions Limits X 95.115(c) Emission Type Transmits Data and ECG Waveform X 95.115(e) Frequency Stability Data Provided By Philips Medical 1 95.1125 RF Safety Statement and Technical Basis 1 Note 1.) Exhibits provided by Philips for approval submission. Page 5 of 39 Compliance Worldwide, Inc. – 357 Main Street – Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com TEST NUMBER - 296-04 TEST RESULTS AND CONCLUSIONS PRODUCT TESTED - Telemetry II Access Point Transceiver MODEL NUMBER - M4842A RADIATED TEST RESULTS The test results show that the emissions radiated from this equipment are in compliance with FCC Rules Part 95. OCCUPIED BANDWIDTH & OUTPUT POWER The test results show that the occupied bandwidth and output power of this equipment are in compliance with FCC Rules Part 95 . CONDUCTED TEST RESULTS The test results show that the emissions conducted on the power from this equipment are in compliance with FCC Rules Part 95. ANALYSIS AND CONCLUSIONS Based upon the radiated and conducted measurements we find that this equipment is within the limits of the FCC Rules Part 95. All results are based on a test of one sample, and represent other production units, only in as much as a sample represents other production units. If any significant changes are made to the unit, the changes shall be evaluated and a retest may be required. NOTES (Special conditions unique to this test) None. Page 6 of 39 Compliance Worldwide, Inc. – 357 Main Street – Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com TEST NUMBER - 296-04 TEST PROCEDURES 1. TEST EQUIPMENT A. HP 8546A (9 kHz - 6.5 GHz) EMI Receiver w/ RF Filter Section, S/N 3704A00323 / 3650A00360. Calibration Date 1-16-2004, calibrated annually. B. HP 8593E (9 kHz - 26.5 GHz) Spectrum Analyzer, S/N 3829A03887. Calibration Date 11-21-2003, calibrated annually. B. Com-Power Biconilog Antenna, Model AC220, S/N 25509. Calibration Date 7-16-2004, calibrated annually. C. Electro-Metrics Double Ridged Guide Antenna, Model EM-6961, S/N 6337. Calibration Date: 7-30-2004, calibrated annually. D. HP 1 - 26.5 GHz Preamplifier, Model 08449B, S/N 3008A01323. Calibration Date: 8-3-2004, calibrated annually. E. EMCO LISN, Model EM 3825/2, S/N 9109-1860. Calibration Date: 3-10-2004, calibrated annually. 2. FREQUENCY RANGE TO BE SCANNED. A. Radiated Test from 30 MHz to 40 GHz (or the 10 th harmonic of the highest frequency whichever is lower). B. Conducted Test from 150 kHz to 30 MHz. Page 7 of 39 Compliance Worldwide, Inc. – 357 Main Street – Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com TEST NUMBER - 296-04 3. TEST PROCEDURES. Radiated test procedure: The EUT, associated cables and peripheral devices are placed on the supporting table and any support equipment is placed off the site. The EUT is turned on and any necessary operating or test software installed and allowed to warm up. The EUT is pre-scanned in our ferrite tile lined chamber where it is rotated 360 degrees and examined in both horizontal and vertical polarization, all emission frequencies are identified and recorded. The EUT is then moved to the OATS and the frequency band from 30 MHz to 40 GHz is scanned, all frequencies identified in the chamber are investigated, as well as harmonic frequencies of the EUT. When an emission is found the emission is maximized by varying the bundle position of the connecting cables, the antenna height, the antenna polarization (vertical and horizontal) and the table orientation (360 degrees). The maximum reading is recorded and the next signal is searched for. Conducted test procedure: The power line of the EUT is connected to the LISN (Line Impedance Stabilization Network). A measurement of the emissions are made from the power line for both ph…

Text truncated - open the document above for the full version.