PQP-WA254TWLAN module

33333333 百一電子股份有限公司 Prime Electronics & Satellitics Inc. WLAN Module WA254T User Manual Specification No. Item ConditionMin. Typ.Max. Test Method/Condition 1. General specification 1-1. Standard IEEE 802.11b 1-2. Frequency Band(MHz) 2400 2497 1-3. No. of Selectable Channels 11 Channels (US, Canada) 13 Channels (Europe) 14 Channel (Japan) 1-4. Channel Spacing (MHz) 5 1-5. Modulation Technique DSSS (CCK, DQPSK, DBPSK) 1-6. Spreading 11-chip Barker Sequence 1-7. Media Access Protocol CSMA/CA(collision Avoidance) with ACK 1-8. Interface 60 pin connector 1-9. Reset Switch Push for normal reset 1-10. LED Indicators Power : Green for Power ON Ethernet : Green for Link ,Blink for active WLAN :Green Blinking for Active 1-11. Antenna One External 2 dBi Dipole Antenna 1-12. Dimensions 110 x 37 x 8 mm 2. Standard Test Condition 2-1. Supply voltage(V) 4.5 3. Electrical Specification Temperature Range：0 ~ 55°C Humidity：95 % (Non-condensing) 470 550 Receiver Mode 3-1. Power Consumption (mA) @+4.5V 650 750 Transmit Mode -76 -78 -82 @ 11 Msps ,Through-Put > 4 Mbps -78 @ 5.5 Msps -81 @ 2 Msps 3-2 Receive Sensitivity (dBm)[FER < 8%] -84 @ 1 Msps 30 @ 11 Msps Indoor 100 @ 1 Msps 150 180250 @ 11 Msps 3-3. Range(Meters) Outdoor 300 @ 1 Msps 3-4. Average Output Power(dBm) Ch1~Ch1314 1518 @30 dBc difference between the signal level at center frequency and higher first side lobe Ch 14 14 1518 @25 dBc difference between the signal level at center frequency and higher first side lobe 3-5 Frequency Accuracy(ppm) - 25 + 25 4. Frequency channel plan Regulation Domains Channel_ID Frequency (Mhz) FCC (0x00) IC (0x01) ETSI (0x02) Spain (0x03) France (0x04) MKK (0x05) MKK2 (0x06) 1 2412 X X X X 2 2417 X X X X 3 2422 X X X X 4 2427 X X X X 5 2432 X X X X 6 2437 X X X X 7 2442 X X X X 8 2447 X X X X 9 2452 X X X X 10 2457 X X X X X X 11 2462 X X X X X X 12 2467 X X X 13 2472 X X X 14 2484 X X Copyright Copyright  2001 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This equipment complies with FCC radiation exposure limits. However, in order to avoid the possibility of exceeding the FCC exposure limits, this device and its antenna should not be co-located or operating in conjunction with any other antenna or transmitter.” This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labelin…

Text truncated - open the document above for the full version.

Report No.: 037H059FI Page : 1 of 3 Version:1.0 Attachment 2 : EUT Detailed Photographs (1) EUT Photo

FCC ID.: PQP-WA254T FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. WLAN module PESI Model No.: WA254T TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan WLAN module Model No.: WA254T F F C C C C I I D D : : P P Q Q P P - - W W A A 2 2 5 5 4 4 T T This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

FCC ID.: PQP-WA254T FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. WLAN module PESI Model No.: WA254T TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan WLAN module Model No.: WA254T F F C C C C I I D D : : P P Q Q P P - - W W A A 2 2 5 5 4 4 T T This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

Report No.: 037H059FI Page : 2 of 3 Version:1.0 (2) EUT Photo Report No.: 037H059FI Page : 3 of 3 Version:1.0 (3) EUT Photo

Report No. 037H059FI Page: 6 of 35 Version:1.0 1.2. Operational Description EUT is a WLAN module with 11 channels. This device provided four kind of transmitting speed 1,2,5.5 and 11Mbps. The device of RF carrier is DQPSK, DB PSK and CCK. The device adapts direct sequence spread spectrum modulation. The Connector antenna was provides diversity function to improve the receiving function. This WLAN module is an IEEE 802.11b Wireless LAN adapter. It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operation in 2.4GHz Direst Sequence Spread Spectrum (DSSS) radio transmission, the WLAN module transfers data at speeds up to 64/128-bit Wired Equivalent Protection (WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any 802.11b network.

Report No. 037H059FI Page: 1 of 3 Version: 1.0 RF Exposure Evaluation declaration Product Name : WLAN module Model No.: WA254T FCC ID.: PQP-WA254T Applicant : PRIME ELECTRONICS & SATELLITICS INC. Address : 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Date of Receipt : Jul 17, 2003 Date of Declaration: Aug 01, 2003 Report No. : 037H059FI The declaration results relate only to the samples calculated. The declaration shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No. 037H059FI Page: 2 of 3 Version: 1.0 1. RF Exposure Evaluation 1.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. Report No. 037H059FI Page: 3 of 3 Version: 1.0 1.3. Test Result of RF Exposure Evaluation Product : WLAN module Test Item : RF Exposure Evaluation Test Site : No.1 OATS Test Mode : Normal Operation Antenna Gain Antenna Gain: The maximum Gain measured in fully anechoic chamber is -1dBi or 0.79 in linear scale. Output Power Into Antenna & RF Exposure Evaluation Distance: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2412.00 35.1560 0.0056 6 2437.00 29.4442 0.0047 11 2462.00 25.2930 0.0040 The power density Pd (4th column) at a distance of 20 cm calculated from the Friis transmission formula is far below the limit of 1 mW/cm 2 .

1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA REVISION RECORD REV ECO DATE DWG TITLE DWG NO. CHECKEDAPPROVED DATEDATE REV Joan 09/Jun/2003 Size Sheet of File Name: A 02 E:\ \ \WA254T(41714-82902)\PCB\41714-82902E L01-A.ddb - Documents\82011-82 9 備份區已發行資料區 USED ON DRAWN 12 WA254T WA254T SCHEMATIC DATE 82011-82902 ES01 Wayne 09/Jun/2003Wayne 09/Jun/2003 DATE ISSUED DATE CHECKED DATE APPROVED XA0 120 XA1 119 XA2 118 XA3 116 XA4 122 XA5 123 XA6 125 XA7 126 XA8 127 XA9 128 XA10 129 XA11 131 XA12 132 XA13 135 XA14 133 XA15 136 XA16 191 XA17 190 XA18 188 XA19 187 XA20 185 XA21 184 XA22 183 XA23 182 NSDCWEOUT# 151 NSDCCASOUT# 149 NSDCRASOUT# 148 NSDCXCS0# 147 NSDCXCS1# 146 SCLK 144 NSMCXOEN# 156 NSMCXCS0# 154 NSMCXCS1# 153 NSMCXCS2# 152 VDD 14 VDD 33 VDD 59 VDD 72 VDD 83 VDD 105 VDD 117 VDD 130 VDD 143 VDD 165 VDD 176 VDD 186 VDD 204 VSS 5 VSS 20 VSS 56 VSS 69 VSS 81 VSS 95 VSS 111 VSS 124 VSS 141 VSS 142 VSS 145 VSS 170 VSS 181 VSS 192 XD0 175 XD1 174 XD2 172 XD3 171 XD4 164 XD5 163 XD6 161 XD7 160 XD8 166 XD9 167 XD10 168 XD11 169 XD12 177 XD13 178 XD14 179 XD15 180 XD16 96 XD17 97 XD18 98 XD19 99 XD20 106 XD21 107 XD22 109 XD23 110 XD24 115 XD25 114 XD26 113 XD27 112 XD28 104 XD29 103 XD30 102 XD31 101 SDCXDQM0 159 SDCXDQM1 158 SDCXDQM2 140 SDCXDQM3 138 VDD_CORE 16 VDD_CORE 22 VDD_CORE 31 VDD_CORE 75 VDD_CORE 86 VDD_CORE 108 VDD_CORE 134 VDD_CORE 139 VDD_CORE 150 VDD_CORE 162 VDD_CORE 189 VDD_CORE 197 VCC_PLL 37 VSS_CORE 10 VSS_CORE 18 VSS_CORE 25 VSS_CORE 79 VSS_CORE 90 VSS_CORE 100 VSS_CORE 121 VSS_CORE 137 VSS_CORE 155 VSS_CORE 173 VSS_CORE 195 VSS_CORE 202 VSS_PLL 36 U6BADM8628 SD_ADDR20SD_ADDR0SD_ADDR1SD_ADDR2SD_ADDR3SD_ADDR4SD_ADDR5SD_ADDR6SD_ADDR7SD_ADDR8SD_ADDR9SD_ADDR10SD_ADDR11SD_ADDR12SD_ADDR13SD_ADDR14SD_ADDR15SD_ADDR16SD_ADDR17SD_ADDR18SD_ADDR19SD_WE#SD_CAS#SD_RAS#SD_CS0#SD_CLKFL_OE#FL_CS1# +3.3V SD_DATA0SD_DATA1SD_DATA2SD_DATA3SD_DATA4SD_DATA5SD_DATA6SD_DATA7SD_DATA8SD_DATA9SD_DATA10SD_DATA11SD_DATA12SD_DATA13SD_DATA14SD_DATA15SD_DATA16SD_DATA17SD_DATA18SD_DATA19SD_DATA20SD_DATA21SD_DATA22SD_DATA23SD_DATA24SD_DATA25SD_DATA26SD_DATA27SD_DATA28SD_DATA29SD_DATA30SD_DATA31SD_DQM0SD_DQM1SD_DQM2SD_DQM3 +2.5V 12 4 53 U374LVC1G00 +3.3V D11N4148 R2610K R25 0 SW1SW_SPST Vout 1 Vss 2 Vin 3 U1 NP/XC61B,SOT23 R1 NP/100 +3.3V +3.3V C31u NET_RESET# T13 RESET CELL + C9410u + C12410u C150.1u C14 0.1u C90 0.1uC109 0.1uC95 0.1uC105 0.1uC108 0.1u C120 0.1uC34 0.1uC111 0.1uC114 0.1uC103 0.1uC57 0.1uC46 0.1u C88 0.1uC16 0.1uC97 0.1uC99 0.1uC102 0.1uC113 0.1uC115 0.1u C1160.1u C1000.1u C980.1u +2.5V SD_ADDR3SD_ADDR4SD_ADDR5SD_ADDR6SD_ADDR7SD_ADDR8SD_ADDR12SD_ADDR13SD_ADDR14SD_ADDR15SD_ADDR17 SD_ADDR[20..0] R58NP/4.7K R59NP/4.7K R60NP/4.7K R61NP/4.7K R62 NP/4.7K R63NP/4.7K R64NP/4.7K R65NP/4.7K R66NP/4.7K R64.7K R12NP/4.7K +3.3V +3.3V A0 25 A1 24 A2 23 A3 22 A4 21 A5 20 A6 19 A7 18 A8 8 A9 7 A10 6 A11 5 A12 4 A13 3 A14 2 A15 1 A16 48 A17 17 A18 16 A19 9 WE# 11 OE# 28 CE# 26 D0 29 D1 31 D2 33 D3 35 D4 38 D5 40 D6 42 D7 44 D8 30 D9 32 D10 34 D11 36 D12 39 D13 41 D14 43 D15 45 VDD 37 VSS 27 VSS 46 NC 47 NC 15 NC 10 NC 12 NC 13 NC 14 U16 SST39LF160(1MX16) SD_ADDR19SD_ADDR0SD_ADDR1SD_ADDR2SD_ADDR3SD_ADDR4SD_ADDR5SD_ADDR6SD_ADDR7SD_ADDR8SD_ADDR9SD_ADDR10SD_ADDR11SD_ADDR12SD_ADDR13SD_ADDR14SD_ADDR15SD_ADDR16SD_ADDR17SD_ADDR18 SD_WE#FL_OE# SD_DATA0SD_DATA1SD_DATA2SD_DATA3SD_DATA4SD_DATA5SD_DATA6SD_DATA7SD_DATA8SD_DATA9SD_DATA10SD_DATA11SD_DATA12SD_DATA13SD_DATA14SD_DATA15 +3.3V 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 55 55 21 21 56 56 22 22 58 58 23 23 60 60 24 24 59 59 25 25 51 51 26 26 52 52 27 27 53 53 28 28 54 54 29 29 57 57 30 30 50 50 31 31 49 49 32 32 48 48 33 33 47 47 34 34 46 46 35 35 45 45 36 36 44 44 37 37 43 43 38 38 42 42 39 39 41 41 40 40 JP5MOLEX_52885 R76 0 R77 0 R78 0 R79 0 R80 0 R81 0 R82 0 R83 0 R84 0 R85 0 R86 0 R87 0 R88 0 R89 0 R90 0 R91 0 R92 0 R93 0 R94 0 R95 0 R96 0 R97 0 R98 0 R99 0 R100 0 R101 0 R102 0 R103 0 R104 0 R105 0 R106 0 R107 0 R108 0 R109 0 R110 0 R111 0 R112 0 R113 0 R114 0 D0D1D2D3D4D5D6D7D8D9D10D11D12D13D14D15A0A1A2A3A4A5A6A7A8A9A10A11A12A13A14A15A16A17A18A19OE#WE#CS# SD_DATA15 SD_ADDR0SD_ADDR1SD_ADDR2SD_ADDR3SD_ADDR4SD_ADDR5SD_ADDR6SD_ADDR7SD_ADDR8SD_ADDR9SD_ADDR10SD_ADDR11SD_ADDR12SD_ADDR13SD_ADDR14SD_ADDR15SD_ADDR16SD_ADDR17SD_ADDR18SD_ADDR19 FL_OE#SD_WE# SD_DATA0 SD_DATA1SD_DATA2SD_DATA3SD_DATA4SD_DATA5SD_DATA6SD_DATA7SD_DATA8SD_DATA9SD_DATA10SD_DATA11SD_DATA12SD_DATA13SD_DATA14 FL_CS1# SD_ADDR[20..0] SD_DATA[31..0] CR_GPIO0CR_GPIO1CR_GPIO2NET_RESET# J1-1J1-2J1-3J1-4-5J1-6J1-7-8 +5V DQM0 16 DQM1 71 DQM2 28 DQM3 59 A0 25 A1 26 A2 27 A3 60 A4 61 A5 62 A6 63 A7 64 A8 65 A9 66 A10/FOR 64MB 24 A11/FOR 128MB 21 BA0 22 BA1 23 CKE 67 CLK 68 CS 20 WE 17 RAS 19 CAS 18 VDD 1 VDD 3 VDD 9 VDD 15 VDD 29 VDD 35 VDD 41 VDD 43 VDD 49 VDD 55 VDD 75 VDD 81 DQ0 2 DQ1 4 DQ2 5 DQ3 7 DQ4 8 DQ5 10 DQ6 11 DQ7 13 DQ8 74 DQ9 76 DQ10 77 DQ11 79 DQ12 80 DQ13 82 DQ14 83 DQ15 85 DQ16 31 DQ17 33 DQ18 34 DQ19 36 DQ20 37 DQ21 39 DQ22 40 DQ23 42 DQ24 45 DQ25 47 DQ26 48 DQ27 50 DQ28 51 DQ29 53 DQ30 54 DQ31 56 VSS 6 VSS 12 VSS 32 VSS 38 VSS 44 VSS 46 VSS 52 VSS 58 VSS 72 VSS 78 VSS 84 VSS 86 U10 W986432DH_86TSOP(2MX32) SD_DQM0SD_DQM1SD_DQM2SD_DQM3 SD_ADDR0SD_ADDR1SD_ADDR2SD_ADDR3SD_ADDR4SD_ADDR5SD_ADDR6SD_ADDR7SD_ADDR8SD_ADDR9SD_ADDR10SD_ADDR11SD_ADDR13SD_ADDR14 SD_CKE R714.7K SD_CLKSD_CS0#SD_WE#SD_RAS#SD_CAS# +3.3V SD_DATA0SD_DATA1SD_DATA2SD_DATA3SD_DATA4SD_DATA5SD_DATA6SD_DATA7SD_DATA8SD_DATA9SD_DATA10SD_DATA11SD_DATA12SD_DATA13SD_DATA14SD_DATA15SD_DATA16SD_DATA17SD_DATA18SD_DATA19SD_DATA20SD_DATA21SD_DATA22SD_DATA23SD_DATA24SD_DATA25SD_DATA26SD_DATA27SD_DATA28SD_DATA29SD_DATA30SD_DATA31 RMII_CRS 6 RMII_COL 7 RMII_RXD3 8 RMII_RXD2 9 RMII_RXD1 11 RMII_RXD0 12 RMII_RXDV 13 RMII_RXCLK 15 RMII_RXER 17 RMII_TXCLK 19 RMII_TXEN 21 RMII_TXD0 23 RMII_TXD1 24 RMII_TXD2 26 RMII_TXD3 27 MII_MDC 28 MII_MDIO 29 L2PHY_RST# 30 JTAG_NTRST# 4 JTAG_TDI 3 JTAG_TMS 2 JTAG_TCK 1 JTAG_TDO 208 UART_DCD# 196 UART_DSR# 198 UART_RXD 199 UART_TXD 200 UART_CTS# 201 XCRYSTA…

Text truncated - open the document above for the full version.

Report No. 037H059FI Page: 1 of 35 Version:1.0 Test Report Product Name : WLAN module Model No.: WA254T FCC ID.: PQP-WA254T Applicant : PRIME ELECTRONICS & SATELLITICS INC. Address : 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Date of Receipt : Jul 17, 2003 Date of Test : Aug 01, 2003 Report No. : 037H059FI The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 037H059FI Page: 2 of 35 Version:1.0 Test Report Certification Test Date : Aug 01, 2003 Report No. : 037H059FI The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Product Name : WLAN module Applicant : PRIME ELECTRONICS & SATELLITICS INC. Address : 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Manufacturer : PRIME ELECTRONICS & SATELLITICS INC. Model No. : WA254T FCC ID. : PQP-WA254T Rated Voltage : DC 5.5V (Power by Battery) Trade Name : PESI Measurement Standard : FCC Part 15 Subpart C Paragraph 15.247 Measurement Procedure : ANSI C63.4: 1992 Test Result : Complied Documented By : ( Carol Tsai ) Tested By : ( Ken Hsu ) Approved By : ( Kevin Wang ) Accredited by NIST (NVLAP) NVLAP Lab Code: 200347-0 Report No. 037H059FI Page: 3 of 35 Version:1.0 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Operational Description ................................................................................................................6 1.3. Tested System Datails....................................................................................................................7 1.4. Configuration of tested System .....................................................................................................8 1.5. EUT Exercise Software .................................................................................................................8 1.6. Test Facility ...................................................................................................................................9 2. Conducted Emission..................................................................................................................10 2.1. Test Equipment............................................................................................................................10 2.2. Test Setup ....................................................................................................................................10 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................11 2.5. Test Result of Conducted Emission.............................................................................................12 3. Peak Power Output ...................................................................................................................14 3.1. Test Equipment............................................................................................................................14 3.2. Test Setup ....................................................................................................................................14 3.3. Limits ..........................................................................................................................................14 3.4. Test Result of Peak Power Output...............................................................................................15 4. Radiated Emission .....................................................................................................................16 4.1. Test Equipment............................................................................................................................16 4.2. Test Setup ....................................................................................................................................16 4.3. Limits ..........................................................................................................................................17 4.4. Test Procedure .............................................................................................................................17 4.5. Test Result of Radiated Emission................................................................................................18 5. Band Edge ..................................................................................................................................24 5.1. Test Equipment............................................................................................................................24 5.2. Test Setup ....................................................................................................................................24 5.3. Limits ..........................................................................................................................................25 5.4. Test Procedure .............................................................................................................................25 5.5. Test Result of Band Edge ............................................................................................................26 6. Occupi…

Text truncated - open the document above for the full version.

Report No.: 037H059FI Page : 1 of 3 Version:1.0 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 037H059FI Page : 2 of 3 Version:1.0 Front View of Radiated Test Back View of Radiated Test Report No.: 037H059FI Page : 3 of 3 Version:1.0 Front View of Radiated Test (Horn)