PQP-WP210GWireless LAN PC Card

W W i i r r e e l l e e s s s s L L A A N N C C a a r r d d B B u u s s C C a a r r d d User Manual Version: 1.0 (September. 2003) Wireless LAN CardBus Card I Copyright Copyright  2001 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. Wireless LAN CardBus Card II Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 2.5cm between the radiator and your body. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. Wireless LAN CardBus Card III EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium, Denmark, Finland, France, (with Frequency channel restrictions) Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not intended for use None. Potential restrictive use France: Only channels 10,11,12, and 13 Wireless LAN CardBus Card IV Manual Contents Chapter 1 Introduction ...................................................... 1 Chapter 2 Initial Installation ...................................................... 2 Chapter 3 Upgrade the Driver ...................................................... 3 Chapter 4 System Tray Icon ...................................................... 6 Chapter 5 Icon Menu ...................................................... 7 Chapter 6 Configuration Utility ...................................................... 8 Chapter 7 Settings ...................................................... 9 7.1 Status Menu ...................................................... 9 7.2 Configuration Menu ...................................................... 11 7.3 Encryption Menu ...................................................... 13 7.4 IBSS Menu ...................................................... 15 7.5 Domain Menu ...................................................... 17 7.6 About Menu 18 Chapter 8 Advanced Properties Tab ...................................................... 19 Chapter 9 Glossary ...................................................... 22 Wireless LAN CardBus Card 1 Chapter 1 Introduction The equipment enabl…

Text truncated - open the document above for the full version.

Report No.: 038H035FI Page : 1 of 6 Version:1.0 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo

PRIME ELECTRONICS & SATELLITICS INC. FCC ID.: PQP-WP210G 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Tel: 886 3-461-5000 FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. Wireless LAN PC Card PESI Model No.: WP210g TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan Wireless LAN PC Card Model No.: WP210g F F C C C C I I D D : : P P Q Q P P - - W W P P 2 2 1 1 0 0 G G This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

PRIME ELECTRONICS & SATELLITICS INC. FCC ID.: PQP-WP210G 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Tel: 886 3-461-5000 FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. Wireless LAN PC Card PESI Model No.: WP210g TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan Wireless LAN PC Card Model No.: WP210g F F C C C C I I D D : : P P Q Q P P - - W W P P 2 2 1 1 0 0 G G This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

Report No.: 038H035FI Page : 2 of 6 Version:1.0 (3) EUT Photo (4) EUT Photo Report No.: 038H035FI Page : 3 of 6 Version:1.0 (5) EUT Photo Report No.: 038H035FI Page : 4 of 6 Version:1.0 (6) EUT Photo Report No.: 038H035FI Page : 5 of 6 Version:1.0 (7) EUT Photo Report No.: 038H035FI Page : 6 of 6 Version:1.0 (8) EUT Photo

1.1. Operational Description EUT is a Wireless LAN PC Card with 11 channels. This device provided four kind of transmitting speed 1,2,5.5 and 11Mbps. The device of RF carrier is DQPSK, DB PSK and CCK(IEEE 802.11b) or eight kinds of transmitting speed 6, 9, 12, 18, 24, 36, 48 and 54Mbps, The device of RF carrier is OFDM(IEEE 802.11g). The device adapts direct sequence spread spectrum modulation. The printed antenna was provides diversity function to improve the receiving function. This Wireless LAN PC Card compliant with IEEE 802.11b and IEEE 802.11g is a high-efficiency Wireless LAN adapter. It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operation in 2.4GHz Direst Sequence Spread Spectrum (DSSS) radio transmission, the Wireless LAN PC Card Wired Equivalent Protection (WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any 802.11b and IEEE 802.11g network.

1 2 3 4 5 6 ABCD 6 5 4 3 2 1 D CBA REVISION RECORD REV ECO DATE DWG TITLE DWG NO. CHECKEDAPPROVED DATEDATE REV Joan 04/Aug/2003 Size Sheet of File Name: A A C:\PCB\ \WP210g .ddb - Documents\82011-80607ES01-A-1.Sch 佳霖 方塊圖 USED ON DRAWN 12 WP210g WP210g SCHEMATIC DATE 82011-80607 ES01 Edward 04/Aug/2003Wayne 04/Aug/2003 DATE ISSUED DATE CHECKED DATE APPROVED BB_OVLD 1 BB_AGC- 2 BB_AGC+ 3 BB_RREF 4 IOFFSET- 5 IOFFSET+ 6 BB_GND 7 QOFFSET- 8 QOFFSET+ 9 PE2 10 MX_GND 11 MX_VCC 12 MX_GND 13 LNA_H/L 14 LNA_VCC 15 LNA_GND 16 SHIELD 17 LNA_IN+ 18 LNA_IN- 19 SHIELD 20 PE1 21 TX_GND 22 TX_OUT 23 TX_GND 24 TX_VCC 25 TX_AGC 26 TX_BB_VCC 27 TX_DETC 28 LO_IN+ 29 QLO_GND 30 LO_IN- 31 QLO_VCC 32 LE 33 REF_IN+ 34 REF_IN- 35 CLK 36 CP_VDD 37 CO_DO 38 CP_GND 39 DATA 40 SYNTH_GND 41 SYNTH_VDD 42 PRE_GND 43 PRE_VDD 44 LD 45 TX_Q- 46 TX_Q+ 47 1.2_REF 48 TX_I- 49 TX_I+ 50 RX_Q- 51 RX_Q+ 52 RX_AGC_VCC 53 RX_AGC_GND 54 RX_I- 55 RX_I+ 56 EP 57 U7 ISL3686A VTUNE 1 VCC 2 GND 3 GND 4 PE 5 VCC 6 GND 7 GND 8 GND 9 OSC- 10 OSC+ 11 VCC 12 GND 13 GND 14 FILTER_CPA1 15 FILTER_CPA2 16 EP 17 U9 ISL3084 C7282P R9314K R271K C71 100P C6910P R261KC601N BB_OVLDBB_AGC-BB_AGC+FSADOFFIOFFSET-IOFFSET+QOFFSET-QOFFSET+ BB_OVLD QOFFSET+ QOFFSET-IOFFSET+ IOFFSET- FSADOFFBB_AGC+ BB_AGC- PE2 LNA_HL PE2 LNA_HL C114 1N C95NPC400.1u C106NP R770 VCCA C681N C161 3P C162 3P UNBAL 2 BAL 4 GND 7 GND 8 NC 1 NC 3 NC 5 BAL 6 U14DBF70A001 C159NP C160NP C94100P R511K C64100P PE1TXAGC PE1 TXAGC R361K R30 TX_IQ_DET TX_IQ_DET C907P C751N C1130.1u C10110u C67100P R351K SYNTH_LE SYNTH_LE VCCB C231N 40MHZ_CW 40MHZ_CW C621N C109100P R25 1K SYNTHCLK SYNTHCLK C76 100P R31 1K R8820 C16810u C117270P C1186.8N C119NP R615.11K R620 SYNTHDATA SYNTHDATA C9110u C860.1u C841N C701N C653P VCCC C1250.1u C171P C12710u C1303P C12310P R342.2K R8447K Q3 MMBT2907AWT1 PE1 PE1 VCCC C803P VCCC C780.68u C730.68u VCCC C891N C630.1u C10056P C10856P R41432 R52432 VCCB R37 1K LOCK_DETC TXQ-TXQ+ LOCK_DETC TXQ- TXQ+ C10756P R49432 C10556P R45432 TXI-TXI+ TXI+ TXI- C10427P R54499 C9927P R44499 C9327P R47499 C9227P R42499 1.2V REF RXQ-RXQ+ RXI-RXI+ 1.2V REF RXQ- RXQ+ RXI- RXI+ C1660.1u GND 1 NC 2 2GHZ_BIAS 3 GND 4 2GHZ_RF_IN 5 GND 6 +3.3V 7 +3.3V 8 GND 9 2GHZ_RF_OUT 10 2GHZ_RF_OUT 11 GND 12 GND 13 2GHZ_DET_OUT 14 GND 15 NC 16 NC 17 GND 18 NC 19 +3.3V 20 +3.3V 21 GND 22 NC 23 GND 24 EP 25 U2 ISL3980 G 1 G 2 G 3 G 5 OUT 4 IN 8 G 6 G 7 U22LF2012 GND 1 GND 2 V1 3 ANT1 4 GND 5 ANT2 6 V2 7 GND 8 GND 9 RX 10 GND 11 TX 12 EP 13 U11 AS218_321 C1710.2P C1761P C77 5P L151.2nH L118.2nH L715nH R55 51 C163100P C1570.1u C15810u C1415P C1540.1u C14510u C887P R700 +3.3V R89 NP C415P R5038.3K PA_DET PA_DET R5927.3K R46 0 C427P C3810P 2GPABIAS 2GPABIAS C57 7P C557P R43 1K C667P ANT_SW* ANT_SW* R481K C797P ANT_SW ANT_SW C30 0ohm C53 7P C11NP C351.5nH L162.2P A1ANTENNA C20NP C5NP L12.2nH A2ANTENNA C50NP R952.7P R943.3P R210 R241K L33.3nH L55.6nH 1 2 3 4 TERM R TERM C CASE GND S3 MM8430,NP R96 0 ANT_SWANT_SW*1.2V REFFSADOFFBB_OVLDSYNTHDATASYNTHCLKTXAGCTX_IQ_DETPA_DETTXQ-TXQ+TXI-TXI+RXQ-RXQ+RXI-RXI+BB_AGC-BB_AGC+QOFFSET-QOFFSET+IOFFSET-IOFFSET+LOCK_DETCSYNTH_LELNA_HLPE1PE22GPABIAS40MHZ_CW 82011-80607ES01-A-282011-80607ES01-A-2.Sch Joan04/Aug/2003Edward04/Aug/2003Wayne04/Aug/2003 A 04/Aug/2003 1 2 3 4 5 6 ABCD 6 5 4 3 2 1 D CBA DWG TITLE DWG NO. CHECKEDAPPROVED DATEDATE REV Joan 04/Aug/2003 Size Sheet of File Name: A A C:\PCB\ \WP210g .ddb - Documents\82011-80607ES01-A-2.Sch 佳霖 方塊圖 USED ON DRAWN 22 WP210g WP210g SCHEMATIC DATE 82011-80607 ES01 Edward 04/Aug/2003Wayne 04/Aug/2003 DATE ISSUED DATE CHECKED DATE APPROVED C480.1u C460.1u C440.1u C390.1u C360.1u C340.1u C330.1u C310.1u C270.1u C250.1u C210.1u C1360.1u C1320.1u C1290.1u C1100.1u C810.1u C740.1u C520.1u C1420.1u C1400.1u C1390.1u C1380.1u C1370.1u C1350.1u C1330.1u C1310.1u C1280.1u C1020.1u C590.1u C510.1u C490.1u C470.1u C450.1u TP58TP R10470 A0 1 A1 2 A2 3 GND 4 SDA 5 SCL 6 NP 7 VCC 8 U6AT24C64 R141K C1520.1u VCCS C1493P R12470 C223P C83NP D5NP C82NP D4NP C80.1u C190.1u R680 R690 C1480.1u C15010u C1430.1u C1440.1u C1460.1u TP54TPTP55TPTP16TPTP18TPTP19TPTP20TPTP21TPTP22TPTP23TPTP25TPTP26TPTP27TPTP28TP VCC 1 VCC 2 NC 3 NC 4 TRST 5 GND 6 GND 8 GND 10 GND 12 GND 14 TDO 7 TDI 9 TMS 11 TCK 13 J3NP VCCS VCCS TP2TPTP3TPTP4TPTP5TPTP6TPTP7TPTP9TPTP10TPTP11TPTP12TPTP13TPTP14TPTP15TPTP17TPTP24TPTP50TPTP51TPTP52TP 1 2 3 U4CMR200T ENB 1 GND 2 OUT 3 VDD 4 U13F4308 A 1 NC 2 C 3 D3BAS21 1234 J1NP RESET 1 CT 2 SHDN 3 SHDN3 4 VIN 13 VIN 14 FAULT 15 RESET 16 EP 17 OUT3 5 CC3 6 GND3 7 GND 8 CC2 9 OUT2 10 CC1 11 OUT1 12 U3 ISL6411IR C2933N C2810u C2633N C310u VCCA C20.1u C410u C610.01u R1682K R7322K 1 23 Q2IRLML6302 23 1 Q1MMBT2222 VCCS C3233N R1 0 R6310 C3710u C430.1u C56NP C5410u VCCB VCCC R33 0 +3.3V 012345678910111213141516171819202122232425262728293031 A0A1A2A3A4A5A6A7A8A9A10A11A12A13A14A15A16A17 R1310K VCCS VCCS C16NP C12NP C7NP C6NP C1NP VCCA VCCA R11 270 R71.5K R74NP L14 BLM18AG1025N1-T C131N C151N R40 R50 VCCB L2560nH C1827P C11510P C116220P R57220K R2310M TP1TP 123456708910111213141516171819202122232425262728293031 R20 R8NP A15A14A5A11A4A3A2A6A13A17A10A9A7A16A0A8A1A12 R6610K VCCS C167NP R6NP R90 C1753P C910u C140.1u R650 C16410u VCCS TP30TP TP56TPTP53TP R80 NP R81 0 R82 NP R83 0 R86 NP R85 NP ANT_SWANT_SW* ANT_SW ANT_SW* TP57TP TP29TP LOCK_DETCSYNTH_LELNA_HL PE1PE22GPABIAS TP48TP TP47TP TP46TP TP45TP TP44TP TP43TP IOFFSET+IOFFSET-QOFFSET+QOFFSET-BB_AGC+ BB_AGC- RXI+RXI-RXQ+RXQ- TP35TP TP36TP TP42TP TP37TP TXI+TXI-TXQ+TXQ- PA_DET TX_IQ_DET TXAGC TP38TP TP39TPTP40TP TP41TP R871.13K R1515.4K R3019.6K R2819.6K R199.76K SYNTHCLK SYNTHDATA BB_OVLDFSADOFF C58 0.1u TP32TP C2468P C151820P R382.2K TP31TP C10362P C153820P R392.2K R29NP R2210K R20NP R18NP VCCS R1712.1K C1470.1u 1.2V REF 1.2V REF FSADOFF BB_OVLD SYNTHDATA SYNTHCLK TXAGC TX_IQ_DET PA_DET TXQ- TXQ+ TXI- TXI+RXQ- RXQ+ RXI- RXI+ BB_AGC- BB_AGC+ QOFFSET- QOFFSET+ IOFFSET- IOFFSET+ A[0..17][0..31] PCI_AD0 F19 PCI_AD1 F17 PCI_AD2 F18 PCI_AD3 G17 PCI_AD4 D19 PCI_AD5 E19 PCI_AD6 E18 PCI_AD7 D20 PCI_AD8 C19 PCI_AD9 B16…

Text truncated - open the document above for the full version.

Report No. 038H035FI Page: 1 of 48 Version:1.0 Test Report Product Name : Wireless LAN PC Card Model No.: WP210g FCC ID.: PQP-WP210G Applicant : PRIME ELECTRONICS & SATELLITICS INC. Address : 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Date of Receipt : Aug 11, 2003 Date of Test : Aug 26, 2003 Report No. : 038H035FI The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 038H035FI Page: 2 of 48 Version:1.0 Test Report Certification Test Date : Aug 26, 2003 Report No. : 038H035FI The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Product Name : Wireless LAN PC Card Applicant : PRIME ELECTRONICS & SATELLITICS INC. Address : 69, Tung-Yuan Rd., Chung-Li Industrial Park, Chung-Li City, Taoyuan, Taiwan. Manufacturer : PRIME ELECTRONICS & SATELLITICS INC. Model No. : WP210g FCC ID. : PQP-WP210G Rated Voltage : DC 3.3V(Power by PC) Trade Name : PESI Measurement Standard : FCC Part 15 Subpart C Paragraph 15.247 Measurement Procedure : ANSI C63.4: 1992 Test Result : Complied Documented By : ( Lydia Tsai ) Tested By : (Ken Hsu ) Approved By : ( Kevin Wang ) Accredited by NIST (NVLAP) NVLAP Lab Code: 200347-0 Report No. 038H035FI Page: 3 of 48 Version:1.0 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Operational Description ................................................................................................................6 1.3. Tested System Datails....................................................................................................................7 1.4. Configuration of tested System .....................................................................................................8 1.5. EUT Exercise Software .................................................................................................................8 1.6. Test Facility ...................................................................................................................................9 2. Conducted Emission..................................................................................................................10 2.1. Test Equipment............................................................................................................................10 2.2. Test Setup ....................................................................................................................................10 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................11 2.5. Test Result of Conducted Emission.............................................................................................12 3. Peak Power Output ...................................................................................................................16 3.1. Test Equipment............................................................................................................................16 3.2. Test Setup ....................................................................................................................................16 3.3. Limits ..........................................................................................................................................16 3.4. Test Result of Peak Power Output...............................................................................................17 4. Radiated Emission .....................................................................................................................19 4.1. Test Equipment............................................................................................................................19 4.2. Test Setup ....................................................................................................................................19 4.3. Limits ..........................................................................................................................................20 4.4. Test Procedure .............................................................................................................................20 4.5. Test Result of Radiated Emission................................................................................................21 5. Band Edge ..................................................................................................................................33 5.1. Test Equipment............................................................................................................................33 5.2. Test Setup ....................................................................................................................................34 5.3. Limits ..........................................................................................................................................35 5.4. Test Procedure .............................................................................................................................35 5.5. Test Result of Band Edge ............................................................................................................3…

Text truncated - open the document above for the full version.

Report No.: 038H035FI Page : 1 of 3 Version:1.0 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 038H035FI Page : 2 of 3 Version:1.0 Front View of Radiated Test Back View of Radiated Test Report No.: 038H035FI Page : 3 of 3 Version:1.0 Front View of Radiated Test (Horn)