PUU-BR30-DMTWIIIDual mode Tunable White BR30

GE Connected BR30 CLEDR309SD1, input 120Vac, frequency was 60Hz, high efficiency, safety & stability output. Use Bluetooth 4.2 and Wi-Fi 2.4G Hz chip technology to realize the far distance control. Through the APP to control the I²C signal to dim and even control the switch on & off of the bulb. Product features: 1. Controlled by Bluetooth 4.2 and Wi-Fi 2.4G to realize the far distance control. 2. CCT range is 2000K-7000K, default CCT is 2700K. 3. With advanced chips to make sure the bulb with high efficiency, low consumption and stability. 4. Internal constant current output to make sure the high power conversion efficiency and stability output. Product Name LED LAMP Brand Name GE Model No. CLEDR309SD1@ @ rates for package information, maybe 1P~10P Working Voltage 120Vac Bluetooth Specification Version 4.2 Wi-Fi Specification 2.4G Hz Frequency Range 2400- 2483.5MHz Channel Number Bluetooth 40 Channel Separation Bluetooth 2MHz Type of Modulation Bluetooth GFSK Data Rate Bluetooth 1Mbps(GFSK) Antenna Type Metal Monopole Antenna Channel Number Wi-Fi 11 Channel Separation Wi-Fi 5MHz Data Rate Wi-Fi 802.11b:11,5.5,2,1 Mbps 802.11g: 54,48,36,24,18,12,9,6 Mbps 802.11n: up to 65Mbps Peak Antenna Gain Bluetooth 1.54dBi Peak Antenna Gain Wi-Fi 1.54dBi For additional help, regulatory and safety Information, please go to: Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. CAUTION: - DO NOT USE WITH STANDARD DIMMERS, SEE INSTRUCTIONS -NOT FOR USE IN TOTALLY ENCLOSED LUMINAIRES -SUITABLE FOR DAMP LOCATIONS -THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control. IC Interference Statement:

Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA 012916 – 09 Authority to Act as Agent Date: __2021.02.05__ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: _____Audix Technology(Shanghai) Co., Ltd.____ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____2022.02.05_____ By: __________________________ ___ Paul Smith ____ (Signature 1 ) (Print name) Title: Systems Engineer – Safety & Regulatory On behalf of: Savant Technologies LLC, dba GE Lighting, a Savant company (Company Name) Telephone: +1 216 266 2189 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA 012916 – 09 Request for Confidentiality Date: __2021.04.02__ Subject: Confidentiality Request for: ____PUU-BR30-DMTWIII____ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* 3 User’s Manual Savant Technologies LLC, dba GE Lighting, a Savant company has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __0__ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: __________________________ _____ Paul Smith ______________ (Signature/Title 3 ) (Print name) 2 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA 012916 – 09 Authority to Act as Agent Date: __2021.02.05__ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: _____Audix Technology(Shanghai) Co., Ltd.____ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____2022.02.05_____ By: __________________________ ___ Paul Smith ____ (Signature 1 ) (Print name) Title: Systems Engineer – Safety & Regulatory On behalf of: Savant Technologies LLC, dba GE Lighting, a Savant company (Company Name) Telephone: +1 216 266 2189 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA 012916 – 09 Request for Confidentiality Date: __2021.04.02__ Subject: Confidentiality Request for: ____PUU-BR30-DMTWIII____ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* 3 User’s Manual Savant Technologies LLC, dba GE Lighting, a Savant company has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __0__ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: __________________________ _____ Paul Smith ______________ (Signature/Title 3 ) (Print name) 2 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

FIGURE 1 DUAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) GENERAL APPEARANCE (GENERAL VIEW) FIGURE 2 D UAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) GENERAL APPEARANCE (COVER REMOVED)

FIGURE 1 DUAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) GENERAL APPEARANCE (COVER REMOVED) FIGURE 2 DUAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) MAIN BOARD (COMPONENT SIDE) FIGURE 3 D UAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) MAIN BOARD (SOLDERED SIDE) FIGURE 4 DUAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) CHIP & CRYSTAL ON BOARD FIGURE 5 D UAL MODE TUNABLE WHITE BR30 (M/N: CLEDR309SD1) ANTENNA Antenna

Applicant: Savant Technologies LLC, dba GE Lighting, a Savant company Product Name: Dual mode Tunable White BR30 Model Number: CLEDR309SD1 FCC ID: PUU‐BR30‐DMTWIII RADIO FRREQUENCY EXPOSURE COMPLIANCE RESULT: Test Standard: FCC CFR 47 §1.1310 : Radiofrequency radiation exposure limits. Note: (1) Occupational/controlled exposure limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when a person is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. (2) General population/uncontrolled exposure limits apply in situations in which the general public may be exposed, or in which persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. MPE Calculation Standard: MPEሺSሻ ൌ PG/ሺ4휋푅 ଶ ) where: S = power density (in appropriate units, e.g. mW/ cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Calculation Result: For this EUT, General population/uncontrolled exposure limits applied. The limit value 1.0mW/cm 2 is available for this EUT. Modulation Peak Output Power Antenna Gain MPE Limit Verdict (dBm) (mW) (dBi) (Numeric) (mW/cm 2 ) (mW/cm 2 ) BLE 4.953 3.12824 1.54 1.42561 0.00089 1 Compliant 802.11b 18.19 65.9174 1.54 1.42561 0.0187 1 Compliant 802.11g 22.71 186.638 1.54 1.42561 0.05293 1 Compliant 802.11n20 22.76 188.799 1.54 1.42561 0.05355 1 Compliant For R = 20cm

Savant Technologies LLC, dba GE Lighting, a Savant company FCC ID: PUU-BR30-DMTWIII Page 1 of 46 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F21092 Prepared For: Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, Cleveland, OH 44112 Prepared By: Audix Technology (Shanghai) Co., Ltd. 3F and 4F, 34Bldg, 680 Guiping Rd., Caohejing Hi-Tech Park, Shanghai 200233, China Tel: +86-21-64955500 File No. : C1D2103107 Report No. : ACI-F21092 Date of Test : 2021.04.10-18 Date of Report : 2021.04.30 TEST REPORT On behalf of Savant Technologies LLC, dba GE Lighting, a Savant company Product Name: Dual mode Tunable White BR30 Model No.: CLEDR309SD1 FCC ID: PUU-BR30-DMTWIII The statement is based on a single evaluation of one sample of the above-mentioned products. It does not imply an assessment of the whole production and does not permit the use of the test lab logo. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TESTING NVLAP LAB CODE 200371-0 Savant Technologies LLC, dba GE Lighting, a Savant company FCC ID: PUU-BR30-DMTWIII Page 2 of 46 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F21092 TABLE OF CONTENTS Page 1 SUMMARY OF STANDARDS AND RESULTS .......................................................................... 5 1.1 Description of Standards and Results ......................................................................................... 5 2 GENERAL INFORMATION .......................................................................................................... 6 2.1 Description of Equipment Under Test ........................................................................................ 6 2.2 EUT Specifications Assessed in Current Report ........................................................................ 7 2.3 Test Information ......................................................................................................................... 7 2.4 Sample Description .................................................................................................................... 7 2.5 Supported equipment .................................................................................................................. 8 2.6 Description of Test Facility ........................................................................................................ 8 3 CONDUCTED EMISSION TEST .................................................................................................. 9 3.1 Test Equipment ........................................................................................................................... 9 3.2 Block Diagram of Test Setup ..................................................................................................... 9 3.3 Conducted Emission Limits (§15.207) ..................................................................................... 10 3.4 Test Configuration .................................................................................................................... 10 3.5 Operating Condition of EUT .................................................................................................... 10 3.6 Test Procedures ........................................................................................................................ 10 3.7 Test Results .............................................................................................................................. 11 4 RADIATED EMISSION TEST ..................................................................................................... 13 4.1 Test Equipment ......................................................................................................................... 13 4.2 Block Diagram of Test Setup ................................................................................................... 13 4.3 Radiated Emission Limit (§15.209) ......................................................................................... 14 4.4 Test Configuration .................................................................................................................... 14 4.5 Operating Condition of EUT .................................................................................................... 15 4.6 Test Procedures ........................................................................................................................ 15 4.7 Test Results .............................................................................................................................. 16 5 6 DB BANDWIDTH MEASUREMENT ...................................................................................... 21 5.1 Test Equipment ......................................................................................................................... 21 5.2 Block Diagram of Test Setup ................................................................................................... 21 5.3 Specification Limits (§15.247(a)(2)) ........................................................................................ 21 5.4 Operating Condition of EUT .................................................................................................... 21 5.5 Test Procedure .......................................................................................................................... 21 5.6 Test Results .............................................................................................................................. 22 6 MAXIMUM PEAK OUTPUT POWER MEASUREMENT ...................................................... 25 6.1 Test Equipment ......................................................................................................................... 25 6.2 Block Diagram of Test Setup ....................................................................................…

Text truncated - open the document above for the full version.

Savant Technologies LLC, dba GE Lighting, a Savant company FCC ID: PUU-BR30-DMTWIII Page 1 of 72 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F21093 Prepared For: Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, Cleveland, OH 44112 Prepared By: Audix Technology (Shanghai) Co., Ltd. 3F and 4F, 34Bldg, 680 Guiping Rd., Caohejing Hi-Tech Park, Shanghai 200233, China Tel: +86-21-64955500 File No. : C1D2103107 Report No. : ACI-F21093 Date of Test : 2021.04.10-18 Date of Report : 2021.04.30 TEST REPORT On behalf of Savant Technologies LLC, dba GE Lighting, a Savant company Product Name: Dual mode Tunable White BR30 Model No.: CLEDR309SD1 FCC ID: PUU-BR30-DMTWIII The statement is based on a single evaluation of one sample of the above-mentioned products. It does not imply an assessment of the whole production and does not permit the use of the test lab logo. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TESTING NVLAP LAB CODE 200371-0 Savant Technologies LLC, dba GE Lighting, a Savant company FCC ID: PUU-BR30-DMTWIII Page 2 of 72 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F21093 TABLE OF CONTENTS Page 1 SUMMARY OF STANDARDS AND RESULTS .......................................................................... 5 1.1 Description of Standards and Results ......................................................................................... 5 2 GENERAL INFORMATION .......................................................................................................... 6 2.1 Description of Equipment Under Test ........................................................................................ 6 2.2 EUT Specifications Assessed in Current Report ........................................................................ 7 2.3 Test Information ......................................................................................................................... 7 2.4 Sample Description .................................................................................................................... 7 2.5 Supported equipment .................................................................................................................. 8 2.6 Description of Test Facility ........................................................................................................ 8 3 CONDUCTED EMISSION TEST .................................................................................................. 9 3.1 Test Equipment ........................................................................................................................... 9 3.2 Block Diagram of Test Setup ..................................................................................................... 9 3.3 Conducted Emission Limits (§15.207) ..................................................................................... 10 3.4 Test Configuration .................................................................................................................... 10 3.5 Operating Condition of EUT .................................................................................................... 10 3.6 Test Procedures ........................................................................................................................ 10 3.7 Test Results .............................................................................................................................. 11 4 RADIATED EMISSION TEST ..................................................................................................... 13 4.1 Test Equipment ......................................................................................................................... 13 4.2 Block Diagram of Test Setup ................................................................................................... 13 4.3 Radiated Emission Limit (§15.209) ......................................................................................... 14 4.4 Test Configuration .................................................................................................................... 14 4.5 Operating Condition of EUT .................................................................................................... 15 4.6 Test Procedures ........................................................................................................................ 15 4.7 Test Results .............................................................................................................................. 16 5 6 DB BANDWIDTH MEASUREMENT ...................................................................................... 24 5.1 Test Equipment ......................................................................................................................... 24 5.2 Block Diagram of Test Setup ................................................................................................... 24 5.3 Specification Limits (§15.247(a)(2)) ........................................................................................ 24 5.4 Operating Condition of EUT .................................................................................................... 24 5.5 Test Procedure .......................................................................................................................... 24 5.6 Test Results .............................................................................................................................. 25 6 MAXIMUM PEAK OUTPUT POWER MEASUREMENT ...................................................... 31 6.1 Test Equipment ......................................................................................................................... 31 6.2 Block Diagram of Test Setup ....................................................................................…

Text truncated - open the document above for the full version.

Test Set-Up Photos 1. Conducted Test 2. Radiated Test (B ELOW 1GHZ) (A BOVE 1GHZ) 3. Antenna-port Conducted Test

Test Set-Up Photos 1. Conducted Test 2. Radiated Test (B ELOW 1GHZ) (ABOVE 1GHZ) 3. Antenna-port Conducted Test