PUU-CANACRRemote control

STOP www.gelighting.com The GE brand and logo are trademarks of the General Electric Company. ©2022 GE Lighting, a Savant company. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. CAN06DW100R9RTWTNRO120, 6016 Model Input voltage (Vac, Hz) Wattage (W) 130 Current (mA) • Risk of fire or electric shock. Installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Minimum 90°C conductors, if uncertain contact a qualified electrician. • These products are suitable for use in wet locations. • IC rated for direct contact with insulation. BEFORE YOU BEGIN Read these instructions completely and carefully. Electrical Requirements The LED fixture must be supplied with 120Vac 60Hz. Grounding Instructions The grounding and bonding of the overall system shall be done in accordance with National Electric Code (NEC) and local codes. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference; (2) this device must accept any interference received, including interference that may cause undesired operation. PREPARE ELECTRICAL WIRING WARNING PRODUCT COVERED Remote Control Wafer light Installation Guide ×4×4×4 ×1 ×1×2×2×2 Wafer light and junction box Gasket Hole templateRemote control Wall faceplateDrywall Anchor ScrewsAdhesive tapes Flathead ScrewdriverStrain Relief Drywall Saw or Hole Saw Ladder Power drill with 15/64” drill bit Safety GogglesMeasuring Tape Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residen- tial area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Note: Reference the guide included with the Installation Mounting Template if using for installation. Installation mounting template sold separately. Not necessary for installation. TOOLS REQUIRED PACKAGE CONTENTS 56 1 2 43 Place the junction box on the ceiling through the hole. Connect the light with junction box with the connector. Hold the spring clips against the fixture and gently guide into the ceiling until the clips snap into place. Turn off power source to the power supply where you are installing the fixture. For a hole size of 6-1/4 inch, Use the hole template to trace the hole size. Cut the hole using a drywall saw or hole saw. Option A:Remove the knockout with a screwdriver and use the strain relief to fish the wires into the J-Box. Option B:use the wire clamps to fish the wires into the J-Box. Connect the wires into quick connector: • Black to black • White to white • Green to green or bare copper wire Close the cover of the junction box. Option A Option B Refer to this section if you bought the trim accessory Decorative Trims (Brushed Nickel, Oil Rubbed Bronze, Square) Wall wash trim Before trim installation, ensure the wafer is powered off. Push the trim into the wafer, ensure all clips on the trim are fixed to the light. Note: Compatible trim accessory: CANAC06BNRO/ CANAC06OBRO/CANAC06BNSQ/ CANAC06OBSQ/- CANAC06WHSQ/ CANAC06WHWW + INSTALLATION TRIM INSTALLATION Mark the appropriate two keyhole locations. Drill two holes 3.28’’ apart using 15/64” size drill bit. Insert drywall anchors • Ensure the installation surface is clean and dry • This product is not suitable for textured, porous, wallpaper or brick wall surface. Screw on the faceplate bracket, then snap the faceplate cover onto the bracket. Then place the remote controller into the groove of the faceplate. Apply adhesive tape to the groove of the faceplate bracket’s back . Then mount the bracket to the wall. Snap the faceplate cover onto the bracket. Then place the remote controller into the groove of the faceplate. This remote controller can be mounted to the wall in two ways, by screws or adhesive tape. Once you determine which install method is best for you, select one of the following setup methods. Note: The wall faceplate is not designed for installation over an outlet box. Option A: Mounting with screws Option B: Mounting with adhesive tape INSTALLATION - REMOTE CONTROLLER WARNING : Chemical Burn Hazard- Do not ingest or swallow coin cell battery. This remote control contains a coin cell battery. If the coin cell battery is swallowed or ingested, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used coin cell batteries away from children. If the battery compartment does not close securely, stop using the remote control and keep away from c hildren. If you think coin cell batteries have been swallowed or placed inside any part of the body, seek immediate medical attention. ① ② User guide: • Turn on light(s) in 30 second, long press and for 5 seconds; the light will flash twice until the controller and lights pair together. Then you can use your controller control to the lights. Note: To pair other devices, repeat the process. • To remove the fixture from the remote: Turn on the light(s) and wait 30 seconds: Long press and for 5 seconds until the light flashes twice. This will remove the device. • Low battery: When the LED indicator light is red, change the battery. • Factory reset: Long press and for 5 seconds until the indicator flashes green. Remove the back cover of remote using the screwdriver to change the CR2032 battery. AVERTISSEMENT : Risque de brûlure chimique - Ne pas ingérer ou avaler la pile bouton. Cette télécommande contient une pil…

Text truncated - open the document above for the full version.

GE Lighting, a Savant company Savant Technologies LLC 1975 Noble Rd., East Cleveland, OH 44112 Certification Application Attestation Statements Date: February 8, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) Savant Technologies LLC dba GE Lighting, a Savant company certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) Savant Technologies LLC dba GE Lighting, a Savant company (“the applicant”) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Thank you, By: __________________________ _________Paul Smith____________ (Signature 2 ) (Print name) Title: _Lead Systems Engineer – safety & Regulatory_ Company: _ Savant Technologies LLC dba GE Lighting, a Savant company Telephone: _(1) 216 266 2189__________ 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters should be placed on appropriate letterhead.

GE Lighting, a Savant company Savant Technologies LLC 1975 Noble Rd., East Cleveland, OH 44112 U.S. Agent Designation for Service of Process (Applicant is Both Grantee and U.S. Agent) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Savant Technologies LLC dba GE Lighting, a Savant company PUU 0022026876 Paul Smith 1975 Noble Road Cleveland, Ohio, United States, 44112 (1) 216 266 2189 [email protected] Applicant Company name: Grantee Code: FRN: Contact Name: Street Address: City/Province/Zip: Telephone No: Email: Applicant Signature: Date: 8 February 2023 Signed by (Printed Name/Title): Paul Smith Lead Systems Engineer – Safety & Regulatory

Savant Technologies LLC dba GE Lighting, a Savant company 050222-17 Request for Confidentiality Date: February 14, 2023 Subject: Confidentiality Request for: ___FCC ID: PUU-CANACR and IC ID:_ 10798A- CANACR _ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term --------------------------- External Photos ☐ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☐ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term --------------------------- Test Setup Photos ☐ Short Term ☐ Permanent * 1 User’s Manual Savant Technologies LLC dba GE Lighting, a Savant company has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications: Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: (specify ISED expiration date / date of marketing) . Sincerely, By: Lead Systems Engineer – Safety & Regulatory _________ Paul Smith _____ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD 050222-17 Authority to Act as Agent Date: December 28, 2022 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: _DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, By: __________________________ _Paul Smith_________________ (Signature 1 ) (Print name) Title: Lead Systems Engineer – Safety & Regulatory__________________________ On behalf of: _ Savant Technologies LLC, dba GE Lighting, a Savant Company _______ (Company Name) Telephone: __+1 216 266 2189_________________________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

FCC ID and IC ID, HVIN, PMN are laser etched to the device FCC ID: PUU-CANACR IC: 10798A-CANACR HVIN: CANACR PMN: Remote control The FCC ID, IC, HVIN, PMN will be laser etched here:

DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: 4394327.54 Page 1 / 9 Test report No: 4394327.54 TEST REPORT Radio Spectrum Matters (RF) Identification of item tested Remote control Trademark / Model and /or type reference CANACR FCC ID PUU-CANACR Features 3Vdc Applicant ́s name / address Savant Technologies LLC dba GE Lighting, a Savant company 1975 Noble Road, Cleveland, Ohio, United States, 44112 Test method requested, standard KDB 447498 D01V06 FCC Part 1.1310 Verdict Summary COMPLIANCE Tested by (name & signature) Johnny Bo Approved by (name & signature) Tim Yan Date of issue 2023-02-05 Report template No TRF_EMC 2017-06- FCC_Exposure DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: 4394327.54 Page 2 / 9 INDEX page General conditions ...................................................................................................................................................... 3 Uncertainty .................................................................................................................................................................. 3 Environmental conditions............................................................................................................................................ 3 Possible test case verdicts ......................................................................................................................................... 3 Definition of symbols used in this test report .............................................................................................................. 4 Abbreviations .............................................................................................................................................................. 4 Document History ....................................................................................................................................................... 4 Remarks and Comments ............................................................................................................................................ 4 1 General Information ........................................................................................................................................... 5 1.1 General Description of the Item(s) .......................................................................................................... 5 1.2 Test data ................................................................................................................................................. 6 1.3 The environment(s) in which the EUT is intended to be used ................................................................ 6 2 Description of Test Setup .................................................................................................................................. 7 2.1 Operating mode(s) used for tests............................................................................................................ 7 2.2 Support / Auxiliary equipment / unit / software for the EUT .................................................................... 7 2.3 Test Configuration / Block diagram used for tests .................................................................................. 7 3 RF Exposure Evaluation .................................................................................................................................... 8 3.1 Limits ....................................................................................................................................................... 8 3.2 Test Procedure ........................................................................................................................................ 9 3.3 Test Result .............................................................................................................................................. 9 DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: 4394327.54 Page 3 / 9 GENERAL CONDITIONS 1. This report is only referred to the item that has undergone the test. 2. This report does not constitute or imply on its own an approval of the product by the Certification Bodies or Competent Authorities. 3. This document is only valid if complete; no partial reproduction can be made without previous written permission of DEKRA. 4. This test report cannot be used partially or in full for publicity and/or promotional purposes without previous written permission of DEKRA. 5. This report will not be used for social proof function in China market. UNCERTAINTY For all measurements where guidance for the calculation of the instrumentation uncertainty of a measurement is specified in EN 55016-4-2 (CISPR 16-4-2), EN/IEC 61000-4 series or a product standard, the measurement instrumentation uncertainty has been calculated and applied in accordance with these standards. Uncertainties have been calculated according to the DEKRA internal document. The reported expanded uncertainties are based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95%. ENVIRONMENTAL CONDITIONS The climatic conditions during the tests are within the limits specified by the manufacturer for the operation of the EUT and the test equipment. The climatic conditions during the tests were within the following limits: Ambient temperature 15 °C – 35 °C Relative Humidity air 30% - 60% Atmospheric pressure 86 kPa – 106 kPa If explicitly…

Text truncated - open the document above for the full version.

ANTENNA PATTERN Max Antenna Gain: 3dBi Model: Ant_YKQ-AK801-A1.0 Manufacturer: FOSHAN ELECTRICAL AND LIGHTING CO., LTD Address ： 64 North Fenjiang Road, Foshan China

DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: 4394327.50 Page 1 / 47 Test report No: 4394327.50 TEST REPORT Radio Spectrum Matters (RF) Identification of item tested Remote control Trademark / Model and /or type reference CANACR FCC ID PUU-CANACR Features 3Vdc Applicant ́s name / address Savant Technologies LLC dba GE Lighting, a Savant company 1975 Noble Road, Cleveland, Ohio, United States, 44112 Test method requested, standard FCC CFR Title 47 Part15 Subpart C Section 15.247; KDB558074 D01v05r02; Verdict Summary COMPLIANCE Tested by (name & signature) Johnny Bo Approved by (name & signature) Tim Yan Date of issue 2022-12-14 Report template No TRF_EMC 2017-06- FCC_Part15C_247 DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: 4394327.50 Page 2 / 47 INDEX page General conditions ...................................................................................................................................................... 4 Uncertainty .................................................................................................................................................................. 4 Environmental conditions............................................................................................................................................ 4 Possible test case verdicts ......................................................................................................................................... 4 Definition of symbols used in this test report .............................................................................................................. 5 Abbreviations .............................................................................................................................................................. 5 Document History ....................................................................................................................................................... 5 Remarks and Comments ............................................................................................................................................ 5 1 General Information ........................................................................................................................................... 6 1.1 General Description of the Item(s) .......................................................................................................... 6 1.2 Test data ................................................................................................................................................. 7 1.3 The environment(s) in which the EUT is intended to be used ................................................................ 7 1.4 Channel List ............................................................................................................................................ 7 2 Description of Test Setup .................................................................................................................................. 8 2.1 Operating mode(s) used for tests............................................................................................................ 8 2.2 Support / Auxiliary equipment / unit / software for the EUT .................................................................... 8 2.3 Test Configuration / Block diagram used for tests .................................................................................. 8 2.4 Measurement procedure ......................................................................................................................... 8 3 Verdict summary section ................................................................................................................................... 9 3.1 Standards ................................................................................................................................................ 9 3.2 Deviation(s) from the Standard(s) / Test Specification(s) ....................................................................... 9 3.3 Overview of results .................................................................................................................................. 9 4 Transmitter Test Results ................................................................................................................................. 10 4.1 AC Power Line Conducted Emission .................................................................................................... 10 4.2 Emissions in non-restricted frequency bands ....................................................................................... 11 4.3 Emissions in restricted frequency bands .............................................................................................. 22 4.4 Band Edge ............................................................................................................................................. 29 4.5 Duty cycle .............................................................................................................................................. 32 4.6 DTS Bandwidth ..................................................................................................................................... 34 4.7 Fundamental emission output power .................................................................................................... 38 4.8 Power Density ....................................................................................................................................... 41 5 Identification of the Equipment Under Test ....................…

Text truncated - open the document above for the full version.

DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: Test setup Page 1 / 2 Radiated measurements <1G Radiated measurements >1G DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch Block 5, No.3, Qiyun Road, Huangpu District, Guangzhou, Guangdong, China Tel +86 20 6661 2000 Fax +86 20 6661 2001 www.dekra-certification.com Report no.: Test setup Page 2 / 2 Conducted RF measurements