PYN2007HHDRemote Control Device

USER GUIDE CSI Doc. 101399-001 Qualifier X-Ray Non-Intrusive Dwelling Ingress Integrity Measurement System Qualifier X-Ray i 1 - 8 0 0 - 3 3 6 - 9 6 8 1 Limited Warranty (brief) Hardware: ComSonics, Inc. (ComSonics) warrants to the original end user (Customer) that the new ComSonics branded products will be free from defects in workmanship and materials, under normal use, for one (1) year from the date of original shipment. ComSonics warrants repaired and refurbished ComSonics products for ninety (90) days from date of shipment. Agency Notice (brief) Hand Held Device Vehicle Mounted Device FCC ID: PYN2007HHD FCC ID: PYN2007VMD IC: 4261A-2007HHD IC: 4261A-2007VMD Complete Limited Warranty and Agency Notice documentation is printed in the back section of this user guide. Technical Support ComSonics maintains a Technical Support Service for customer convenience. Contact a Support Representative at 1-800-336-9681 or 1-540-434-5965; Fax 1-540-432-9794; or Email [email protected]. Copyright All material in this manual is the property of ComSonics, Inc. and protected under the United States copyright law. No material shall be reproduced or used in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems) without the written permission of: ComSonics, Inc. 1350 Port Republic Road Post Office Box 1106 Harrisonburg, Virginia 22801 USA Phone: (540) 434-5965 USA Toll Free: (800) 336-9681 Fax: (540) 434-9847 Email: [email protected] Internet: www.comsonics.com Qualifier™ is a trademark of ComSonics, Inc. © 2007 ComSonics, Inc. All Rights Reserved CSI Doc. 101399-001 Rev. 1.05 sh w w w . c o m s o n i c s . c o m ii Table of Contents Introduction .......................................................................................................1 FCC License Requirement ...........................................................................1 Unpacking ....................................................................................................1 Qualifier X-Ray System Overview ................................................................2 General Information..........................................................................................3 Hand Held Device (HHD) .............................................................................3 Battery Installation .................................................................................3 Single Button Control .............................................................................3 Auto Power Off ......................................................................................3 Display Screen.......................................................................................4 Threshold Value Setup ..........................................................................4 Hardware Installation ...................................................................................6 Dual Band Antenna................................................................................7 Vehicle Mount Device (VMD).................................................................7 Check / Select Transmit Frequency.......................................................8 Test the VMD Installation.......................................................................8 Qualifier System Installation Verification ......................................................9 Troubleshooting Notes .................................................................................9 Using the Qualifier X-Ray System.................................................................10 Dwelling Shielding Integrity Measurement Procedure ...............................10 Specifications .................................................................................................11 Accessories / Parts.........................................................................................12 Warranty Statement ........................................................................................13 Agency Notice .................................................................................................15 Qualifier X-Ray iii 1 - 8 0 0 - 3 3 6 - 9 6 8 1 Major Components Power Button Test Button Status Indicators Antenna Connector Battery Compartment Power Harness Connector Fuse Power / Test Button Display Screen Input Connector w w w . c o m s o n i c s . c o m 1 Introduction FCC License Requirement A FCC license is required to operate the Qualifier X-Ray System, specifically the vehicle mount transmitter component (VMD). Refer to the Qualifier Transmitter Licensing section on our website at www.comsonics.com/downloads.html for application instructions and templates. If you need assistance, please call our Customer Service Department at 1-800- 336-9681. Unpacking The Qualifier X-Ray System and accessories are shipped in a single container designed to provide maximum protection during transit. Immediately upon receipt, inspect the container and contents for signs of physical damage. Notify the freight forwarder of any damage detected. Installation Caution! The Qualifier X-Ray System is designed only for vehicles equipped with a 12-volt negative ground electrical system. Qualifier X-Ray 2 1 - 8 0 0 - 3 3 6 - 9 6 8 1 Qualifier X-Ray System Overview The ComSonics Qualifier X-Ray System provides a method for identifying the internal shielding integrity of the CATV network in a subscriber’s residence without the need to enter the premises. A test activation transmitter is located within the Qualifier hand held device (HHD). The transmitter provides an activation signal to the Qualifier Vehicle Mounted Device (VMD) and sets up the HHD to measure levels of ingress from the VMD signal appearing in the return upstream path. With the HHD connected to either the residential ground block or the drop tap, a press of the HHD button activates the VMD to ge…

Text truncated - open the document above for the full version.

Hand Held Device Block DiagramReference: Schematic Rev A of February 27, 2007QualifierX-RayHHDBlockDiagram.odt June 26, 2007 RECEIVER BPF 27 MHz RF Power Measurement AD8310 U1 Input Connector BNC J1 MeasEn Level RF Input Range 27.45 - 27.49 M Hz +3V LDO Regulator LP3988 +3V U2 LED Driver 3904 Q3 AAA Batteries x3 Alkaline Push Button S1 Dual Diode MMBD7000 D2 Battery Level Q4, Q5 +VBatt BatVolt USER PwrEn BattGood +3V BL_CATHODEBL_EN POWER AND BUTTON CONTROL Transmitter 433.92 ASK MC33493 U4 Crystal Y1 13.56 MHz Moderate Q PCB Loop Antenna TxENTxCLKSDA +3V TRANSMIT TRIGGER LCD Panel / Backlight w/ Controller +3V LCD_CS SCK SDA BL_ANODE LCD_SPARE BL_CATHODE DISPLAY +3V BL_ANODE MeasEn Controller MC68HC908QY2 U5 Program J10 BatVolt Level TxCLK BattGood User (R6) SCKSDALCD_CS BL_EN MeasEn TxEn LCD_SPARE PwrEn PROCESSOR CONTROL Program Disconnect TPC6102 Q6 +3V

Washington Laboratories, Ltd. 7560 LINDBERGH DRIVE GAITHERSBURG, MD 20879 (301) 417 – 0220 FAX # (301) 417 - 9069 August 30, 2002 Mr. Tim Johnson American Telecommunications Certification Body Inc. 6731 Whittier Ave McLean, VA 22101 RE: Comments of August 1, 2002 APPLICATION: P9X-EMS-MM-GE Eka Systems, Inc. Dear Mr. Johnson: Below are the comments that you have provided regarding the application for certification referenced above. Our responses to those comments are in bold italic. Many responses refer you to additional exhibit(s) which has been uploaded to the application folder at the ATCB website. Thank you for your attention. Please feel free to contact us for any additional information that you may require. Regards, Steven D. Koster EMC Operations Manager Brian J. Dettling Documentation Specialist WLL Project: 7044 1) The FCC application form shows confidentiality is requested but no letter requesting confidentiality of exhibits has been provided. Either provide a confidentiality letter or amend the application form. Confidentiality can be requested for the block diagram exhibit, the schematic diagram exhibit and the operational description exhibit. The parts list exhibit is not needed since the schematic diagram has component values on it. The additional information exhibit that contains operating parameters of the MC33493 transmitter cannot be held confidential because it is available on Motorola’s Website at www.freescale.com. Response to ATCB Comments FCC ID: ???????? 2 R. Per the text message added to the application, the applicant is not seeking confidentiality. The 731 form has been corrected. Please see “HHD Application Form - 731 revised”. 2) The test report does not contain a 99% bandwidth for IC compliance as required by Section A1.1.3 of RSS-210, Issue 7. Please provide this data in an amended test report. R. The report has been corrected. Please see “HHD Test Report revised”. 3) The IC application form submitted to ATCB has the wrong company number on page 1 and 2 of the form. The correct company number for Comsonics is 4261A not 4761A as shown on the IC application form. In addition, the information on page 2 of this form for Field Strength, Emission Designator, and Transmitter Spurious has not been completed. Please submit a corrected IC application form. R. The form has been corrected. Please see “HHD Application Form – IC revised”. 4) The model number listed on Annex A of RSS-102 (page 3 of the IC application form) does not agree with the model number on the IC application form submitted to ATCB. The model number is 101393-001 not HHD as shown on Annex A. Please submit a corrected Annex A. R. Please see “HHD Application Form – IC revised”. 5) For Your Information – I have noticed two minor errors in the user’s manual for this device. I recommend that they be corrected as soon as possible. a. The statement required by Section 15.21 of the FCC Rules really belongs under the section of the manual for the HHD device not the VMD device. b. The IC statement from Section 7.1.5 of RSS-Gen, Issue 2 should be under the IC section of the user manual. Currently no statement is there. Either add this statement or place a combined FCC and IC statement at the beginning of this information about the compliance of the device to both FCC and IC standards. Since these statements are similar many manufacturers are doing this. R. This has been passed on to the client. Thank you.

External Photos ©2007 Washington Laboratories, Ltd External Photos ©2007 Washington Laboratories, Ltd External Photos ©2007 Washington Laboratories, Ltd

WHERE USED DATEREV ZONE DESCRIPTION REVISIONS APPROVED ECN ANG } 0.5ANG } 0.5 FRAC } FRAC } .XXX } 0.005.XXX } 0.005 TOLERANCES ARE:TOLERANCES ARE: OTHERWISE SPECIFIED.OTHERWISE SPECIFIED. DIMENSIONS ARE IN INCHES UNLESSDIMENSIONS ARE IN INCHES UNLESS DEC.XX } 0.01DEC.XX } 0.01 IF APPLICABLEIF APPLICABLE REMOVE BURRS. BREAK SHARP EDGES.REMOVE BURRS. BREAK SHARP EDGES. 1 OF 1 1350 PORT REPUBLIC RD. 1350 PORT REPUBLIC RD. HARRISONBURG, VA. 22801HARRISONBURG, VA. 22801 (540) 434-5965 (540) 434-5965 www.comsonics.com www.comsonics.com IS AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR QUOTATION THIS DOCUMENT IS THE PROPERTY OF COMSONICS INC. ITS USE MUST BE REFERRED TO THE COMSONICS PURCHASING DEPARTMENT. OR FOR THE PERFORMANCE OF WORK FOR COMSONICS. ALL QUESTIONS DO NOT SCALE DRAWING 1.00 .40 SCALE 2 X SCALE 1 X J.C. GLENN REV DOC SHEET SIZE A SCALE: FSCM NO.DWG.NO. DATE DR CHK CONTRACT NO. SIGNATURES ENG MATERIAL FINISH 5/23/05 Qualifier X-Ray HHD Model Bar Code LABEL 101447C.ai C 101447 101393-001 ARELEASE PLACE BAR CODE AS SPECIFIED MATERIAL= WHITE VINYL WITH PSA ON OTHER SIDE INK COLOR = INDELIBLE BLACK on WHITE BARCODE = BLACK IN WHITE SPACE BELOW MODEL NO. EACH LABEL BARCODE PROGRESSING IN NONE REPEATING BAR CODING INCREMENTS, 00050000 THRU 00069999 CENTERED IN SPACE BELOW MODEL NO. Generated in: Adobe Illustrator 8.0 Filename 101447B.ai PART -001 BARCODE PRINTING SPECIFICATIONS: COLOR = BLACK FONT = REGULAR POINT SIZE = 5 TYPEFACE = ARIAL Code = 128 HEIGHT = .100 CODE SET = C X DIMENSION = 8.2 DENSITY = 11.054 CHARACTERS PER INCH QUALITY = A MRKTMRKT PURCHPURCH 7/25/06D.B.B. 7/25/06D.B.B. B CHG'D TO 8 DIGIT SERIAL NO. 2089 12/28/06D.B.B. ComSonics Inc. Model 101393-001ComSonics Inc. Model 101393-001 IC: 4261A-2007HHDIC: 4261A-2007HHD FCC ID: PYN2007HHDFCC ID: PYN2007HHD MadeMade in USAin USA ComSonics Inc. Model 101393-001ComSonics Inc. Model 101393-001 IC: 4261A-2007HHDIC: 4261A-2007HHD FCC ID: PYN2007HHDFCC ID: PYN2007HHD MadeMade in USAin USA CADD FCC & IC NUMBERS - PRELIMINARY

Internal Photos ©2007 Washington Laboratories, Ltd Internal Photos ©2007 Washington Laboratories, Ltd Internal Photos ©2007 Washington Laboratories, Ltd Internal Photos ©2007 Washington Laboratories, Ltd

Theory of Operation - Radio System Qualifier X-Ray Hand Held Device (HHD) RF energy is produced at U4 (MC33493) a self-contained ASK Transmitter IC. Output frequency is controlled by a crystal at Y1 (13.56MHz), which serves as the reference for an internal PLL circuit to the MC33493, and programming of internal PLL registers. Transmitter output is prohibited if the PLL is out of lock. The internal PLL registers are programmed by the microcontroller at U5. Maximum RF output level is determined by the resistor value at R8 (12K). The microcontroller at U5 (MC68HC908QY2) controls the transmitter's frequency, mode of operation (On Off Keying - OOK), and produces the data stream sent by the transmitter. The antenna is contained within the unit's outer, plastic housing and consists of a copper trace on the printed circuit board. The antenna is approximately 1-7/8” in length. The MC33493 data sheet is included in this documentation package.

55 44 33 22 11 D D C C B B A A Push to Power On 50 Ohm Cable Input RF PowerMeasurement AAA Batteries 27.47 MHz BPF Moderate QPCB LoopAntenna 433.92 MHz ASKTransmitter Controller + + +- - - LDORegulator Battery VoltageCheck Auto-Disconnect for 5V Programmer LCD Connection(Note crossoverrelative to LCDconnector) THIS DOCUMENT IS THE PROPERTY OF COMSONICS INC. ITS USEIS AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR QUOTATIONOR FOR THE PERFORMANCE OF WORK FOR COMSONICS. ALL QUESTIONSMUST BE REFERRED TO THE COMSONICS PURCHASING DEPARTMENT. 1 1 A Qualifier X-Ray, HHD C:\WORK\COMSONICS\QUALIFIER\HHD\REV C\QUAL_HHD_REV C.D SN B Tuesday, February 27, 2007 S101394 ComSonics TITLE:SIZE: DWG. NO.: FILE: REV.: SHEET: OF EDITED: 1350 PORT REPUBLIC RD. HARRISONBURG, VA. 22801 (540) 434-5965 WWW.COMSONICS.COM BL_AnodeBL_Cathode DISABLE Level MeasEn BattGood SDA TxCLK TxEn SCKSDA PwrEn Level TxEnMeasEn TxCLK BatVolt SCK LCD_CS SDA LCD_CS LCD_Spare LCD_Spare BatVolt USER USER PwrEn BL_En BL_EnBattGood MeasEn GND +3V +VBatt +3V +3V +3V +3V +VBatt +VBatt +3V +VBatt +3V C14 1uF U2 LP3988 5 2 3 4 1 Vout GND EN GOODVin C13 330pF C3 47pF S1 SW-Tact 12 34 C6560pF L31uH Q5 3904 3 1 2 C16 0.1uF C9 1uF L1 5.6uH FB1 1 2 C7 82pF C4 0.1uF U5 MC68HC908QY2 54 16 18 1291315141110 7632 PA4/OSC2/KB4/AD2PA5/OSC1/KB5/AD3 VSS VDDPA3/RST/KB3 PA1/TCH1/KB1/AD1 PA2/IRQKB2/TCLK PA0/TCH0/KB0/AD0 PB0PB1PB2PB3 PB4PB5PB6PB7 Q3 3904 3 1 2 J1 BNC 1 2 3 4 5 R1010 R9 4.7K A C10 1uF16V 12 J3AAClip 1 2 3 D2 MMBD 7000 2 3 1 R144.7K FB7 1 2 FB6 12 L5 36nH J6AAClip 1 2 3 FB8 1 2 FB3 1 2 R17 100K R13 100K FB9 12 C17 330pF R1212K J4AAClip 1 2 3 Q6 TPC6102 3 1 4 256 J5 Flex 12345678 J10CON16A 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 C18 3.3pF R11 100K R7 510 R18 12K C15 330pF U1 AD8310 81 2 3 45 6 7 In+In- GND OFLT VOUT VCC BFIN ENA Y1 13.56MHz 1 23 4 L2 56nH C19 8.2pF J7AAClip 1 2 3 R6 4.7K R3 100K C2 5pF R4 100K R512K C1 0.1uF J2AAClip 1 2 3 J8AAClip 1 2 3 U4MC33493 123 13 4 5 9 710 86 12 14 11 DATACLKDATABANDENA GND XTAL1 VCC REXT RFOUT CFSKXTAL0 VCC MODE RFGND R16100K C8 10nF Q4 3906 3 1 2 C5 0.1uF R812K R15 100K

Document 9886-01, Rev. 1 FCC ID: PYN2007HHD IC ID: 4261A-2007HHD FCC and IC Certification Test Report Washington Laboratories, Ltd August 2007 FCC & Industry Canada Certification Test Report for Comsonics Inc. FCC ID: PYN2007HHD IC ID: 4261A-2007HHD Revised September 7, 2007 Prepared for: Comsonics, Inc. 1350 Port Republic Rd. Harrisonburg, VA, 22801 Prepared By: Washington Laboratories, Ltd. 7560 Lindbergh Drive Gaithersburg, Maryland 20879 FCC & IC Certification Test Report Document 9886-01, Rev. 1 FCC ID: PYN2007HHD IC ID: 4261A-2007HHD FCC and IC Certification Test Report Washington Laboratories, Ltd August 2007 Page 1 of 21 FCC & Industry Canada Certification Test Report for the Comsonics, Inc. Qualifier X-Ray HHD FCC ID: PYN2007HHD IC ID: 4261A-2007HHD August 28, 2007 WLL JOB# 9886 Prepared by: Steven Dovell Compliance Engineer Reviewed by: Steven D. Koster EMC Operations Manager Document 9886-01, Rev. 1 FCC ID: PYN2007HHD IC ID: 4261A-2007HHD FCC and IC Certification Test Report Washington Laboratories, Ltd August 2007 Page 2 of 21 Abstract This report has been prepared on behalf of Comsonics, Inc. to support the attached Application for Equipment Authorization. The test report and application are submitted for a Periodic Intentional Radiator under Part 15.231 of the FCC Rules and Regulations and Spectrum Management and Telecommunications Policy RSS-210 of Industry Canada. This Federal Communication Commission (FCC) Certification Test Report documents the test configuration and test results for a Comsonics, Inc. Qualifier X-Ray HHD. Testing was performed on an Open Area Test Site (OATS) of Washington Laboratories, Ltd, 7560 Lindbergh Drive, Gaithersburg, MD 20879. Site description and site attenuation data have been placed on file with the FCC's Sampling and Measurements Branch at the FCC laboratory in Columbia, MD. The Industry Canada OATS numbers are 3035A-1 and 3035A-2 for Washington Laboratories, Ltd. Site 1 and Site 2, respectively. Washington Laboratories, Ltd. has been accepted by the FCC and approved by NIST NVLAP (NVLAP Lab Code: 200066-0) as an independent FCC test laboratory. The Comsonics, Inc. Qualifier X-Ray HHD complies with the limits for a Periodic Intentional Radiator device under FCC Part 15.231 and Industry Canada RSS-210. Document 9886-01, Rev. 1 FCC ID: PYN2007HHD IC ID: 4261A-2007HHD FCC and IC Certification Test Report Washington Laboratories, Ltd August 2007 Page 3 of 21 Table of Contents Abstract ............................................................................................................................... ii 1 Introduction..............................................................................................................4 1.1 Compliance Statement ........................................................................................ 4 1.2 Test Scope ........................................................................................................... 4 1.3 Contract Information........................................................................................... 4 1.4 Test Dates ........................................................................................................... 4 1.5 Test and Support Personnel ................................................................................ 4 2 Equipment Under Test .............................................................................................5 2.1 EUT Identification & Description ...................................................................... 5 2.2 Test Configuration .............................................................................................. 5 2.3 Testing Algorithm............................................................................................... 5 2.4 Test Location ...................................................................................................... 5 2.5 Measurements ..................................................................................................... 6 2.5.1 References....................................................................................................... 6 2.6 Measurement Uncertainty................................................................................... 6 3 Test Equipment ........................................................................................................7 4 Test Results ..............................................................................................................8 4.1 Transmission Duty Cycle Correction ................................................................. 8 4.2 Transmission Cessation from Time-of-Release................................................ 11 4.3 Occupied Bandwidth: (FCC Part §2.1049) ....................................................... 12 4.4 Radiated Spurious Emissions............................................................................ 13 4.4.1 Test Procedure .............................................................................................. 13 List of Tables Table 1. Device Summary................................................................................................... 5 Table 2: Test Equipment List............................................................................................. 7 Table 3. Radiated Emissions Test Data – X Orthogonal ................................................. 14 Table 4: Radiated Emissions Test Data - Y Orthogonal................................................... 17 Table 5: Radiated Emissions Test Data - Z Orthogonal ................................................... 19 Table 6: Radiated Emissions Test Data - Non-Harmonic................................................. 21 List of Figures Figure 1: Duty Cycle of Transmission – Single Pulse........................................................ 9 Figure 2: Duty Cycle of Transmission - Over 100ms....................................................... 10 Figure 3. Time…

Text truncated - open the document above for the full version.

Test Setup Photos ©2007 Washington Laboratories, Ltd Test Setup Photos ©2007 Washington Laboratories, Ltd Test Setup Photos ©2007 Washington Laboratories, Ltd