Q2O-VISO1APWireless Airplay Music System

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ ® Owner’s Manual Wireless AirPlay® Music System SAVE THESE INSTRUCTIONS FOR LATER USE FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT. 1. Read instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean only with dry cloth. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture - Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. The primary method of isolating the amplifier from the mains supply is to disconnect the mains plug. Ensure that the mains plug remains accessible at all times. Unplug the AC power cord from the AC outlet if the unit will not be used for several months or more. The socket-outlet shall be installed near the equipment and shall be easily accessible. 12. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13. Power Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 15. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power line surges. 16. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. WARNING: THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING, AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS. AS WITH ANY ELECTRONIC PRODUCTS, USE CARE NOT TO SPILL LIQUIDS INTO ANY PART OF THE SYSTEM. LIQUIDS CAN CAUSE A FAILURE AND/OR A FIRE HAZARD. 19. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a When the power supply cord or plug is damaged. b If liquid has been spilled, or objects have fallen into the product. c If the product has been exposed to rain or water. d If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adj…

Text truncated - open the document above for the full version.

FCC ID: Q2O-VISO1AP

INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model : VISO 1 AP (External) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model : VISO 1 AP (External)

INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) c INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal) INTERTEK TESTING SERVICE Report No.: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Equipment Photographs Model: VISO 1 AP (Internal)

INTERTEK TESTING SERVICE FCC ID: Q2O-VISO1AP Analysis Report The Equipment Under Test (EUT) is a Wireless Airplay Music System, equipped with a 2.4GHz WiFi (6201) and Bluetooth (CSR8645) modules. The 2.4GHz WiFi (6201) module is controlled by network media processor DM870 to provide Airplay music streaming features. The Bluetooth (CSR8645) modules provides audio playback via Bluetooth device. The 2.4GHz WiFi (6201) operates in the frequency range between 2412MHz and 2462MHz (11 channels with 5 MHz channel spacing, 802.11 b and g only). The Bluetooth (CSR8645) module operates in the frequency range between 2402MHz and 2480MHz (79 channels with 1 MHz channel spacing). The EUT can also accept digitized audio signal from LAN network (Intertek Radio), USB flash and TOSLINK SPDIF optical input. The EUT has built-in digital power amplifier driving the internal loudspeakers. The EUT is powered by 100-240VAC (universal input with earth pin). The 2.4GHz WiFi module (6201) contains two antennas. Only one antenna is emitting at the same time. Bluetooth module (CSR8645) contains single antenna only. WiFi and Bluetooth do not emit simultaneously in actual product operation. WiFi Antenna Type: Internal, Integral (antenna 1 and 2: 2412MHz – 2462MHz, 11 channels, 5MHz spacing) Bluetooth Antenna Type: Internal, Integral (single antenna: 2402MHz – 2480MHz, 79 channels, 1MHz spacing) The WiFi and Bluetooth modules were tested in according with the following power output and in actual application the below limit shall not be exceeded. Operating mode Nominal Production Modulation Antenna Radiated Tolerance Type Gain Field Strength 802.11b 104.8dBμV/m at 3m +/- 10dB DSSS 0 dBi 96.9dBμV/m +/- 3dB 802.11g 98.3dBμV/m at 3m +/- 10dB OFDM 0 dBi OFDM m +/- 3dBdBμV/m at 3m +/- 3dB Bluetooth 90.5dBμV/m at 3m +/- 10dB GFSK 0 dBi INTERTEK TESTING SERVICE FCC ID: Q2O-VISO1AP For the WiFi (wireless LAN) module, the Maximum Permissible Exposure (MPE) evaluation of the VISO 1 AP Wireless Airplay Music System, the maximum power density at 20 cm from this mobile transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65. For Wireless Airplay Music System of tested model VISO 1 AP, the maximum field strength of WiFi (wireless LAN) module measured (FS) was 114.8 dBμV/m. The distance (D) between the antenna and the equipment under test (EUT) was 3 meters. From these data, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The radiated power = (FS*D)^2 / 30 = 90.6 mW The power density at 20 cm from the antenna = EIRP / 4πR^2 = 0.018 mW cm-2 In the frequency range of 1,500 - 100,000MHz, the MPE limit is 1.0 mWcm-2 for general population and uncontrolled exposure. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the VISO 1 AP at least 20cm from nearby persons.” INTERTEK TESTING SERVICE FCC ID: Q2O-VISO1AP For the Bluetooth module, the Maximum Permissible Exposure (MPE) evaluation of the VISO 1 AP Wireless Airplay Music System, the maximum power density at 20 cm from this mobile transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65. For Wireless Airplay Music System of tested model VISO 1 AP, the maximum field strength of Bluetooth module measured (FS) was 100.5 dBμV/m. The distance (D) between the antenna and the equipment under test (EUT) was 3 meters. From these data, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The radiated power = (FS*D)^2 / 30 = 3.37 mW The power density at 20 cm from the antenna = EIRP / 4πR^2 = 0.00067 mW cm-2 In the frequency range of 1,500 - 100,000MHz, the MPE limit is 1.0 mWcm-2 for general population and uncontrolled exposure. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the VISO 1 AP at least 20cm from nearby persons.”

Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 13010205HKG-001 i FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com GENERAL INFORMATION Lenbrook Industries Limited BRAND NAME: NAD, MODEL: VISO 1 AP FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Grantee: Lenbrook Industries Limited Grantee Address: Room D, 11th Floor, Wing Cheong Commercial Building, 19-25 Jervois Street, Central, Hong Kong. Contact Person: Jes Arcenal Tel: 852-2517 8292 Fax: 852-2517 4404 e-mail: [email protected] Manufacturer: Dongguan Kwan Hong Electronics Co., Ltd. Manufacturer Address: KwanHong Building, Xiao Bian 2 nd Industrial Zone, ChangAn, DongGuan, China. Brand Name: NAD Model: VISO 1 AP Type of EUT: Transceiver Description of EUT: Wireless Airplay Music System Serial Number: N/A FCC ID / IC: Q2O-VISO1AP / 152B-VISO1AP Date of Sample Submitted: January 08, 2013 Date of Test: January 08 to May 03, 2013 Report No.: 13010205HKG-001 Report Date: May 16, 2013 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 13010205HKG-001 ii FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com SUMMARY OF TEST RESULT Lenbrook Industries Limited BRAND NAME: NAD, MODEL: VISO 1 AP FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP TEST SPECIFICATION REFERENCE RESULTS Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.4 Pass Transmitter Field Strength and Bandwidth Requirement 15.249 / RSS-210 A2.9 Pass Receiver / Digital Device Radiated Emissions 15.109 / RSS-210 2.5 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2011 Edition RSS-210 Issue 8, December 2010 RSS-Gen Issue 3, December 2010 Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 13010205HKG-001 iii FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com Table of Contents 1.0 General Description....................................................................................... 1 1.1 Product Description ...................................................................................... 1 1.2 Related Submittal(s) Grants .......................................................................... 2 1.3 Test Methodology ......................................................................................... 2 1.4 Test Facility .................................................................................................. 2 2.0 System Test Configuration ............................................................................ 3 2.1 Justification................................................................................................... 3 2.2 EUT Exercising Software .............................................................................. 3 2.3 Special Accessories...................................................................................... 3 2.4 Equipment Modification................................................................................. 3 2.5 Measurement Uncertainty ............................................................................. 4 2.6 Support Equipment List and Description........................................................ 4 3.0 Emission Results........................................................................................... 5 3.1 Field Strength Calculation ............................................................................. 5 3.2 Radiated Emission Configuration Photograph ............................................... 6 3.3 Radiated Emission Data ............................................................................... 6 3.4 Conducted Emission Configuration Photograph ............................................ 6 3.5 Conducted Emission Data............................................................................. 6 4.0 Equipment Photographs .........…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Configuration Photographs Worst-Case Radiated Emissions (Front View) Model: VISO 1 AP 13010205HKG-001 VISO 1 AP Side-A INTERTEK TESTING SERVICE Report No: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP Configuration Photographs Worst-Case Radiated Emissions (Rear View) Model: VISO 1 AP 13010205HKG-001 VISO 1 AP Side-B

INTERTEK TESTING SERVICE Report No: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP i Configuration Photographs Worst-Case Line-Conducted Emissions (Front View) Model: VISO 1 AP INTERTEK TESTING SERVICE Report No: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP ii Configuration Photographs Worst-Case Line-Conducted Emissions (Rear View) Model: VISO 1 AP INTERTEK TESTING SERVICE Report No: 13010205HKG-001 FCC ID: Q2O-VISO1AP IC: 152B-VISO1AP iii Configuration Photographs Worst-Case Line-Conducted Emissions (Side View) Model: VISO 1