Q3HM200Fall Monitor, M200

M200 Fall Monitor SETUP & USER GUIDE document #: Draft KB#: TBD Published: January 2021 Copyright Information All content herein is the property of STANLEY Healthcare, its Affiliates, or their content suppliers and is protected by United States and international copyright laws. The compilation of all content is likewise the exclusive property of STANLEY Healthcare (or the Affiliate identified in any copyright notice) and is protected by United States and international copyright laws. The trademarks, service marks and logos (the ‘Trademarks’) used and displayed in this publication are registered and unregistered Trademarks of STANLEY Healthcare, its Affiliates and others. Nothing herein should be construed as granting, by implication, estoppel or otherwise, any license or right to use any Trademark displayed herein without the prior consent of the Trademark owner. STANLEY and the STANLEY design are two of the trademarks owned by STANLEY Healthcare and/or its Affiliates (“STANLEY Trademarks”). STANLEY Trademarks may not be used in connection with any product or service that is not manufactured by or under license from STANLEY Healthcare or its appropriate Affiliate. Important Recommendation STANLEY Healthcare’s systems are designed to assist staff in providing a high degree of safety for people and assets and therefore should be used as a component of a comprehensive safety program of policies, procedures, and processes. As with every safety system, STANLEY Healthcare highly recommends regular system operational checks to verify functional integrity. There are no known issues with the usage of this equipment in association with other investigations or treatments at the facility. Cautions and Warnings CAUTION FAILURE TO HEED THE FOLLOWING CAUTIONS COULD RESULT IN HARM TO YOUR SYS- TEM OR CAUSE IT TO FUNCTION IMPROPERLY, INTERMITTENTLY, OR NOT AT ALL. • Use the M200 Fall Monitor only with approved accessories. • Remove batteries when the Monitor is not in use to avoid battery power loss. • Use care when connecting the Sensormat® pads. Gently remove or connect cords using the retaining tab. Pulling on cords may damage them and/or result in system failure. WARNING FAILURE TO HEED THE FOLLOWING WARNINGS COULD RESULT IN INJURY TO OR THE DEATH OF PERSONS IN YOUR CARE. • A low battery condition in the Monitor is indicated by the Low Battery indicator flashing YELLOW once every 3 seconds, a Negative Confirmation Tone, as well as a “Low Battery” voice indication. Immediately change the monitor’s batteries. • Test the M200 Fall Monitor and Sensormat pad before each use and inspect the cords and pads for signs of damage. Immediately replace any components with signs of wear or damage. • Sensormats may not be effective with air type bed mattresses or air type chair cushion pads; test before using. • Do not place the monitor within 0.3 m (1 ft.) of and facing the resident. Placing the Monitor on a wheelchair back is acceptable as long as the monitor is facing away from the resident. • The M200 Fall Monitor is only one part of your facility’s fall management program. The M200 Fall Monitor is not a substitute for proper nursing care or routine visual monitoring by caregivers. The effectiveness of the M200 Fall Monitor relies entirely on an immediate response by the caregiver to the M200 Fall Monitor system alarm. • The M200 Fall Monitor system will not stop a person from leaving a bed or chair. It is intended only to alert a caregiver that a patient or resident may need assistance. Other interventions may be required. • Keep the Sensormat pad flat at all times. Folding the pad may damage it. Do not use the pad if it has been folded. • Do not immerse the Sensormat pads in liquids. The pad will not operate properly if the pad is exposed to excessive liquids. If the pad is immersed in liquid, discard it immediately. • Operators of this equipment must be familiar with the functions and usage as described in this manual, and must be properly trained in the resident care policies and procedures of the facility. • Any modification of this equipment is not allowed, voids all warranties, and may result in injury to or death of persons in your care. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ATTENTION RISQUE D’EXPLOSION SI LA PILE EST REMPLACÉE PAR UN TYPE INCORRECT. SE DÉBARRASSER DES PILES USAGÉES SELON LES INSTRUCTIONS. Contents Copyright Information ........................................................................................................ ii Important Recommendation ........................................................................................... ii Cautions and Warnings....................................................................................................... ii Introduction.....................................................................................................1 Check Your Shipment .......................................................................................................... 1 Other Components Sold Separately .............................................................................. 1 Overview ..........................................................................................................2 Hardware Features ........................................................................................3 Speaker..................................................................................................................................... 4 Reset Button ........................................................................................................................... 4 Front Panel Status Indicators............................................................................................ 4 Battery Covers........................................................................................................................ 7 Control Settings ........…

Text truncated - open the document above for the full version.

Date: December 30, 2020 Federal Communications Commission Authorization and Evaluation Division To: Federal Communications Commission Confidentiality Request regarding application for the FCC certification of FCC ID: Q3HM200 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: a. CONF APPENDIX M200 Partlst.pdf b. CONF APPENDIX M200 BlkDia.pdf c. CONF APPENDIX M200 Schem.pdf d. CONF APPENDIX M200 OpDes.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Thank you, Signature: Reuven Amsalem VP HW R&D

Date: December _30_, 2020 To Whom It May Concern We hereby authorize Mr. Ilan Cohen of I.T.L. (Product Testing) Ltd (ITL) to act on our behalf regarding the following FCC certification application: FCC ID: Q3HM200 Thank you, Signature: Reuven Amsalem VP HW R&D

Date: December 30, 2020 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Ilan Cohen of I.T.L. (Product Testing) Ltd (ITL) to sign FORM 731 on our behalf for the following FCC certification application: FCC ID: Q3HM200 Thank you, Signature: Reuven Amsalem VP HW R&D

Date: December 30, 2020 Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: The AeroScout, FCC ID: Q3HM200, and label are so small that it cannot include the statement specified in FCC Part 15 Sub-part A, Section 15.19 (a) (3) “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation." Due to this reason, we are using the provisions of Part 15 Sub-part A, Section 15.19 (a) (5) and this statement appears in a prominent location in the user manual. Please contact me if there is any information you may need. Thank you, Signature: Reuven Amsalem VP HW R&D

HVIN is in the 2D barcode Label Location

Date: December 30, 2020 To: Federal Communications Commission FCC ID: Q3HM200 No manual tune-up procedure required. Thank you, Signature: Reuven Amsalem VP HW R&D

Test Report E220831.01 AeroScout Page 1 of 53 FCC ACC M Ver 1.2 28 February 2011 DATE: 4 January 2021 I.T.L. (PRODUCT TESTING) LTD. FCC/IC Radio Test Report for AeroScout Equipment under test: Fall Monitor M200 Tested by: ________________________ M. Zohar Approved by: _________________________ D. Shidlowsky This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. Test Report E220831.01 AeroScout Page 2 of 53 FCC 15.247 DTS Conducted Ver 1 25.11.2018 Measurement/Technical Report for AeroScout Fall Monitor M200 FCC ID: Q3HM200 IC: 5115A-M200 This report concerns: Original Grant: X Class I Change: Class II Change: Equipment type: FCC: (DTS) Digital Transmission System IC: Spread Spectrum Digital Device (2400- 2483.5) Limits used: 47CFR15 Section 15.247 RSS 247, Issue 2, February 2017, Section 5 RSS-Gen, Issue 5, April 2018 Measurement procedure used is KDB 558074 D01 v05r03,ANSI C63.10:2013, and RSS-Gen, Issue 5, April 2018 Application for Certification Applicant for this device: prepared by: (different from "prepared by") R. Pinchuck Reuven Amsalem ITL (Product Testing) Ltd. AeroScout 1 Bat Sheva Street 2 Ilan Ramon St., Science Park Lod, 7116002 Ness-Ziona, 7403635, Israel Israel Tel: +972-8- 936-9393 e-mail [email protected] Fax: +972-8- 936-5977 e-mail: : [email protected] Test Report E220831.01 AeroScout Page 3 of 53 FCC 15.247 DTS Conducted Ver 1 25.11.2018 TABLE OF CONTENTS 1. GENERAL INFORMATION --------------------------------------------------------------------------- 5 1.1 Administrative Information ........................................................................... 5 1.2 List of Accreditations ................................................................................... 6 1.3 Product Description ..................................................................................... 7 1.4 Test Methodology ........................................................................................ 7 1.5 Test Facility ................................................................................................. 7 1.6 Measurement Uncertainty ........................................................................... 8 2. SYSTEM TEST CONFIGURATION ----------------------------------------------------------------- 9 2.1 Justification .................................................................................................. 9 2.2 EUT Exercise Software ............................................................................... 9 2.3 Special Accessories .................................................................................... 9 2.4 Equipment Modifications ............................................................................. 9 2.5 Configuration of Tested System ................................................................ 10 3. CONDUCTED & RADIATED MEASUREMENT TEST SET-UP PHOTOS ------------- 11 4. CONDUCTED EMISSION FROM AC MAINS -------------------------------------------------- 14 4.1 Test Specification ...................................................................................... 14 4.2 Test Procedure .......................................................................................... 14 4.3 Test Limit ................................................................................................... 14 4.4 Test Results............................................................................................... 15 5. 6 DB MINIMUM BANDWIDTH --------------------------------------------------------------------- 21 5.1 Test Specification ...................................................................................... 21 5.2 Test Procedure .......................................................................................... 21 5.3 Test Limit ................................................................................................... 21 5.4 Test Results............................................................................................... 21 5.5 Test Equipment Used; 6dB Bandwidth ..................................................... 23 6. MAXIMUM CONDUCTED OUTPUT POWER -------------------------------------------------- 24 6.1 Test Specification ...................................................................................... 24 6.2 Test Procedure .......................................................................................... 24 6.3 Test Limit ................................................................................................... 24 6.4 Test Results............................................................................................... 24 6.5 Test Equipment Used; Maximum Peak Power Output .............................. 26 7. BAND EDGE SPECTRUM -------------------------------------------------------------------------- 27 7.1 Test Specification ...................................................................................... 27 7.2 Test Procedure .......................................................................................... 27 7.3 Test Limit ................................................................................................... 27 7.4 Test Results............................................................................................... 27 7.5 Test Equipment Used; Band Edge ............................................................ 29 8. TRANSMITTED POWER DENSITY -------------------------------------------------------------- 30 8.1 Test Specification ...................................................................................... 30 8.2 Test Procedure .......................................................................................... 30 8.3 Test Limit ................................................................................................... 30 8.4 Test Results...............................................…

Text truncated - open the document above for the full version.

Conducted & Radiated Measurement Test Set-Up Photos Conducted Emission from AC Line Test Radiated Emission Test, 0.009-30MHz Radiated Emission Test, 30-200MHz Radiated Emission Test, 200-1000MHz Radiated Emission Test, 1-18GHz