Q3HTAG1200SBAsset Tag

T12SB Environmental Tags Deployment & User Guide 0980-507-000 REV XXX Updated: 2022/03/15 CAUTION AND WARNINGS Electromagnetic radiation emitted from AeroScout Tags may interfere with critical care equipment. Please refer to the equipment manufacturer's user manuals for electromagnetic immunity guidance, and for separation distance recommendations, if applicable. Use this link, https://www.stanleyhealthcare.com/support, to locate our published specifications for SECURITAS Healthcare/AeroScout tag transmission frequencies and output power, or contact SECURITAS Healthcare Technical Support at +1-800-380-8883 for assistance. Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in Improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 1 cm to any part of the ME Equipment or ME System, including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result. Disclaimer The information and know-how included in this document are the exclusive property of SECURITAS Healthcare and are intended for the use of the addressee or the user alone. The addressees shall not forward to another their right of using the information, know-how or document forwarded herewith, in whole or in part in all matters relating or stemming from or involved therein, whether for consideration or without consideration, and shall not permit any third party to utilize the information, know-how or the documents forwarded herewith or copies or duplicates thereof, unless at the company’s consent in advance and in writing. Any distribution, advertisement, copying or duplication in any form whatsoever is absolutely prohibited. The Company reserves the right to sue the addressee, user and/or any one on their behalves, as well as third parties, in respect to breaching its rights pertaining to the intellectual rights in particular and its rights of whatever kind or type in the information, know-how or the documents forwarded by them herewith in general, whether by act or by omission. This document is confidential and proprietary to SECURITAS Healthcare and is not to be distributed to any persons other than licensed AeroScout Visibility System users or other persons appointed in writing by SECURITAS Healthcare. Trademark Acknowledgements AeroScout is a trademark of SECURITAS Black & Decker, Inc. or its affiliates. Other brand products and service names are trademarks or registered trademarks of their respective holders. Below is a partial listing of other trademarks or registered trademarks referenced herein: Cisco™ is a trademark of Cisco Systems, Inc. Sun, Sun Microsystems, the Sun Logo, Java, JRE and all other Sun trademarks, logos, product names, service names, program names and slogans that are referred to or displayed in this document are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. This product includes software developed by the Apache Software Foundation (http://www.apache.org/). This product includes code licensed from RSA Data Security. Skype, SkypeIn, SkypeOut, Skype Me, the Skype Logo and the S logo and other marks indicated on Skype’s website are trademarks of Skype Limited or other related companies. Esper is a trademark of EsperTech, Inc. Jboss is a trademark of Red Hat Middleware, LLC. Oracle 10G is a registered trademark of Oracle Corporation and/or its affiliates. MS SQL Server is a registered trademark of Microsoft Corporation in the United States and/or other countries. JasperSoft, the JasperSoft Logo, JasperReports, the JasperReports logo, JasperIntelligence, JasperDecisions, JasperAnalysis, Scope Center, Scope Designer, and JasperServer are trademarks or registered trademarks of JasperSoft, Inc. in the United States and other countries. iCloud Drive, iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store® is a service mark of Apple Inc., registered in the U.S. and other countries. ©2022 SECURITAS Healthcare. All rights reserved. Doc: 0980-507-000 REV B. Updated: 2022/03/15. KB Article: 12297. T12s Asset Tags Deployment & User Guide 4 Table of Contents Introduction ....................................................................... 5 T12s Asset Tag Features ....................................................... 6 Tag Descriptions ................................................................. 7 Replacing the Battery ................................................................................................. 8 Approved Batteries ................................................................................................. 8 Tag Specifications ................................................................ 9 Environmental Specifications ................................................................................... 9 Physical and Mechanical .......................................................................................... 9 Electrical ............................................................................................................... 9 Visual Indications ................................................................................................... 9 Radio .................................................................................................................... 9 Certification ........................................................................................................... 9 Appendix .......................................................................... 10 Safety, Warnings and Warranty ........................................... 11 Introduction The T12SB Bi-directional environmental Tags are components of SEC…

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10-07-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: Q3HTAG1200SB AeroScout Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Reuven Amsalem VP Development Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10-07-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: Q3HTAG1200SB AeroScout Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Reuven Amsalem VP Development

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-20-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: Q3HTAG1200SB AeroScout Inc. (“the applicant”) certifies that, as of the date of the filing of the application, STANLEY Healthcare is our designated U.S. agent for service of process for the above referenced FCC ID. AeroScout Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. STANLEY Healthcare accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: STANLEY Healthcare FRN: 0029011335 Applicant's FRN: 0008786550 Address: 4600 Vine Street, Lincoln, NE, 68502 Contact Person: Garth Jack Tel.: 402-742-9335 Email: [email protected] Sincerely, AeroScout Inc. STANLEY Healthcare Reuven Amsalem Garth Jack Rev 1/26/2023

Date: 4/23/2023 To: Federal Communications Commission, 7435 Oakland Mills Road, Columbia, MD 21046, USA Attn: Reviewing Engineer To Whom It May Concern: AeroScout's FCC ID: Q3HTAGB1200SB and label are so small, that it cannot include the statement specified in 47 CFR Part 15 Sub-part A, Section 15.19 (a) (3). Under the provisions of 47 CFR Part 15 Sub-part A, Section 15.19 (a) (5), this statement appears in a prominent location in the user manual. Thank you, Reuven Amsalem VP HW R&D

Date: 4/25/2023 To: Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046, USA Subject: Request for Confidentiality Ref: FCC ID numbers Model FCC ID T12SB Q3HTAG1200SB To whom it may concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, AeroScout Inc. hereby requests confidential treatment for equipment authorization referenced above. Permanent Confidentiality AeroScout Inc. requests that the Commission withholds the following documents from public viewing indefinitely: • Parts list • Block diagram • Schematics • Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Short Term Confidentiality In addition to the above-mentioned documents, pursuant to Public Notice DA 041705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, AeroScout Inc. requests that the Commission withholds the following documents from public viewing for one hundred eighty days after the date the grant of equipment authorization is issued: • External Photographs • Internal Photographs • Test Setup Photographs • User Manual Sincerely, Reuven Amsalem VP, Development

Date: 4/25/2023 To: Timco Engineering, Inc., an IIA Company 849 NW State Road 45 Newberry, Florida 32669 We hereby authorize Mr. Netanel Yakobov of I.T.L. Product Testing Ltd., to sign Form 731 on our behalf, for the following FCC/ISED certification application/s: FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB Thank you, Reuven Amsalem VP, Development

Date: 10/10/2023 To Whom It May Concern, We hereby authorize Mr. Netanel Yakobov of I.T.L. Product Testing Ltd., to act on our behalf regarding the following FCC/ISED certification application: FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB Thank you,

Page 1 of 4 External Photos FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB Page 2 of 4 Page 3 of 4 Page 4 of 4

FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB

FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB

Page 1 of 4 Internal Photos FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB Page 2 of 4 Page 3 of 4 Page 4 of 4

p. 1 of 6 RF Exposure / SAR Exclusion Report Applicant AeroScout Inc. Applicant Address 2 Ilan Ramon St. Science Park, Ness-Ziona 7403635, Israel Product Asset Tag FCC ID Q3HTAG1200SB IC 5115A-TAG1200SB Standard(s) FCC Part 15, Subpart C RSS-247, Issue 2, February 2017, Section 5 RSS-Gen, Issue 5, April 2018 Test Report No. Ra266060.01 Prepared by: Ram Ezrah Reviewed by: Netanel Yakobov Date: 31 July 2023 p. 2 of 6 1 EUT Information Model No. T12S Power supply 3 Vdc Antenna type Integral Antenna gain +0.7 dBi Assigned frequency range 2402-2483.5 MHz Operating frequency range Wi-Fi: 2412-2462 MHz BLE: 2402-2480 MHz Transmit power (conducted) BLE: -1.09 dBm Wi-Fi: 19.79 dBm Modulation bandwidth WIFI: 20 MHz BLE: 1/2 MHz Bit rate 72 MB/s (MCS7) Distance from human body (min.) 5 mm 2 Evaluation Method and Limits 2.1 FCC: MPE (Maximum Permissible Exposure) assessment • 47 CFR Section 1.1310(e)(1) The limits for Maximum Permissible Exposure (MPE) to radiofrequency electromagnetic fields are as described in table 1 to § 1.1310(e)(1). See below. p. 3 of 6 • KDB447498 D01 V06 “RF Exposure Procedures and Equipment Authorization Policies for Mobile and Portable Devices” v06, Section 4.3.1: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance defined in 4.1 f) is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander". p. 4 of 6 2.2 ISED The limits for Maximum Permissible Exposure (MPE) to radiofrequency electromagnetic fields are as described in RSS-102 - Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus, table 4. See below. • RSS-102, Issue 5, March 2015, Sections 2.5.2, 3, and 4, table 4. According to RSS-102, Section 3, “Devices that have a radiating element normally operating at or below 6 GHz, with a separation distance of up to 20 cm between the user and/or bystander and the device, shall undergo a SAR evaluation. Devices that have a radiating element normally operating at or below 6 GHz, with a separation distance greater than 20 cm between the user and/or bystander and the device shall undergo an RF exposure evaluation. However, a SAR evaluation may be performed in lieu of an RF exposure evaluation for devices operating below 6 GHz with a separation distance of greater than 20 cm between the user and/or bystander and the device. Devices operating above 6 GHz regardless of the separation distance shall undergo an RF exposure evaluation.” p. 5 of 6 2.3 Calculated MPE 1. Max. power (conducted): a) BLE: -1.09 dBm = 0.78 mW = 0.00078 W b) Wi-Fi: 19.79 dBm = 95.28 mW = 0.0953 W 2. Antenna gain: 0.7 dBi 3. EIRP = Max. power + gain = a) BLE: -1.09 + 0.7 = -0.39 b) Wi-Fi: 19.79 + 0.7 = 20.49 4. Tune-up tolerance (according customer declaration) = <0.002% 5. EIRP (including tune-up tolerance): a) BLE: -0.39 + 20 * log(0.002) = -54.37 dBm = 0.000004 mW p. 6 of 6 b) Wi-Fi: 20.49 + 20 * log(0.002) = -33.49 dBm = 0.00045 mW 6. Minimum distance from human body: 5 mm = 0.005 m 3 Test Results Power terms Frequency (MHz) Calculation Limit Verdict BLE 2,402.0 [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] *·[√f(GHz)] = [(0.000004)/(5)]* [√2.4] = 0.00031 7 PASS Wi-Fi 2,412.0 [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] *·[√f(GHz)] = [(0.00045)/(5)]* [√2.4] = 0.0035 7 PASS 4 Conclusion The measurement results comply with the limits per the abovementioned FCC requirements. End of Report

Test Report Ra266060.03 AeroScout Inc. Page 1 of 88 FCC 15.247 DTS Conducted Ver 1 25.11.2018 Date: 8 October 2023 International Testing Labs Ltd. FCC/ISED Radio Test Report for AeroScout Inc. Equipment under test: Asset Tag T12SB FCC ID: Q3HTAG1200SB IC: 5115A-TAG1200SB Tested by: N. Yakobov Approved by: M. Zohar This report must not be reproduced, except in full, without the written permission of International Testing Labs Ltd. This report relates only to items tested. Test Report Ra266060.03 AeroScout Inc. Page 2 of 88 FCC 15.247 DTS Conducted Ver 1 25.11.2018 This report concerns: Original Grant Equipment type: FCC: (DTS) Digital Transmission System ISED: Spread Spectrum Digital Device (2400-2483.5) Limits used: 47CFR15 Section 15.247 RSS-247, Issue 2, February 2017, Section 5 RSS-Gen, Issue 5, April 2018 Measurement procedure: KDB 558074 D01 v05r01,ANSI C63.10:2013 RSS-Gen, Issue 5, April 2018 Applicant: Reuven Amsalem AeroScout Inc. 2 Ilan Ramon St., Science Park Ness-Ziona 7403635, Israel Email: [email protected] Test Report Ra266060.03 AeroScout Inc. Page 3 of 88 FCC 15.247 DTS Conducted Ver 1 25.11.2018 Table of Contents 1 General Information ----------------------------------------------------------------------------------------- 5 1.1 Administrative Information ........................................................................................... 5 1.2 Product Description ..................................................................................................... 5 1.3 Test Methodology ........................................................................................................ 6 1.4 Measurement Uncertainty ........................................................................................... 6 2 System Test Configuration -------------------------------------------------------------------------------- 8 2.1 Justification .................................................................................................................. 8 2.2 EUT Exercise Software ............................................................................................... 8 2.3 Special Accessories .................................................................................................... 8 2.4 Equipment Modifications ............................................................................................. 8 2.5 Configuration of Tested System .................................................................................. 9 3 Test Setup Photos------------------------------------------------------------------------------------------ 10 4 6 dB Minimum Bandwidth ------------------------------------------------------------------------------- 11 4.1 Test Specification ...................................................................................................... 11 4.2 Test Procedure .......................................................................................................... 11 4.3 Test Limit ................................................................................................................... 11 4.4 Test Results .............................................................................................................. 11 4.5 Test Equipment Used; 6dB Bandwidth ..................................................................... 23 5 Maximum Conducted Output Power ----------------------------------------------------------------- 24 5.1 Test Specification ...................................................................................................... 24 5.2 Test Procedure .......................................................................................................... 24 5.3 Test Limit ................................................................................................................... 24 5.4 Test Results .............................................................................................................. 24 5.5 Test Equipment Used; Maximum Peak Power Output .............................................. 36 6 Band Edge Spectrum -------------------------------------------------------------------------------------- 37 6.1 Test Specification ...................................................................................................... 37 6.2 Test Procedure .......................................................................................................... 37 6.3 Test Limit ................................................................................................................... 37 6.4 Test Results .............................................................................................................. 37 6.5 Test Equipment Used; Band Edge ............................................................................ 45 7 Transmitted Power Density ----------------------------------------------------------------------------- 46 7.1 Test Specification ...................................................................................................... 46 7.2 Test Procedure .......................................................................................................... 46 7.3 Test Limit ................................................................................................................... 46 7.4 Test Results .............................................................................................................. 46 7.5 Test Equipment Used; Transmitted Power Density .................................................. 58 8 Occupied Bandwidth -------------------------------------------------------------------------------------- 59 8.1 Test Specification ...................................................................................................... 59 8.2 Test Procedure .......................................................................................................... 59 8.3 Test Limit ..................................…

Text truncated - open the document above for the full version.

Material FR4, The antenna is part of a multi-layered PCB Black is Copper FR4 L1 -Antenna Layer L2 -GND 10 mil’ Behind the Antenna Layer Structure of T12sb Antenna Ver2 Material FR4, The antenna is part of a multi-layered PCB Black is Copper Antenna Layer L1 -Layer 1 of file T12s_Ant_ver 2 .dxf L2 –GND Layer 2 of file T12s_Ant_ver 2 .dxf T12s Antenna Ver2 -Layers All dimensions-mm Contour + Via between Antenna layer to GND (L1 to L2) Layer 3 of file T12s_Ant_ver 2 .dxf Contour and Vias(platting drills) between Antenna layer to GND. Diameter of drills 0.254 mm before platting. 18.4 28.5 18.4 28.5 12.5 20.7 11.2 9.3 8.8 18.4 28.5 Simulation model Band 2.4GHz

FCC ID: Q3HTAG1200SB Figure 2. Conducted Emission Test Figure 5. Radiated Emission Test, 30.0-200.0 MHz Figure 6. Radiated Emission Test, 200.0-1000.0 MHz Figure 7. Radiated Emission Test, 1.0-18.0 GHz Figure 8. Radiated Emission Test, 18-26.5 GHz