Q6G-AP300WatchGuard AP

WatchGuard® Technologies, Inc. Quick Start Guide WatchGuard ® AP AP300 快速入门指南 Guide de démarrage rapide Kurzanleitung Guida introduttiva クイックスタート・ガイド 빠른 시작 가이드 Guía Rápida Guia de início rápido 快速設定手冊 Connect the WatchGuard AP English 1. Connect an Ethernet cable to the Ethernet interface on the WatchGuard AP device. 2. Connect the other end of the Ethernet cable to your network, or directly to a trusted or optional Firebox interface with DHCP enabled. You must enable DHCP on the network or Firebox interface where you connect the AP device. If you do not use DHCP on your network, manually configure the IP address for the AP device as described below before you connect the AP device to your network. 3. If you do not use PoE, connect a power adapter to your AP device and a power source. The device powers on. The Power/Status light flashes when the AP device is ready to pair. 1 Pair the WatchGuard AP with a Firebox If this is your first AP device, you must enable the Gateway Wireless Controller on the Firebox. 1. Open your Firebox configuration in Policy Manager or the Fireware Web UI. 2. Select Network > Gateway Wireless Controller. 3. Enable the Gateway Wireless Controller. 4. Set a passphrase the Firebox will use to connect to paired AP devices. 5. If you use Policy Manager, save the configuration to the Firebox. To pair the AP device to your Firebox 1. In the Gateway Wireless Controller configuration, on the Access Points tab, click Refresh to discover the AP device. 2. Select the unpaired Access Point and click Pair. 3. Type the default AP device passphrase: wgwap Next Steps To complete your WatchGuard AP configuration, use the Gateway Wireless Controller to: • Configure AP device radio and security settings. • Create one or more SSIDs for your wireless network. • Assign the SSID to your AP device. • Save the configuration to your Firebox. • Verify that your AP device is online in Firebox System Manager or the Web UI Gateway Wireless Controller Dashboard. For more information about how to set up your AP device, see the Fireware Help at http://www.watchguard.com/wgrd-help/documentation/overview. 2 Manually configure the AP device address Connect to the WatchGuard AP device web UI to manually assign the AP device a static IP address. 1. Use an Ethernet cable to directly connect your computer to the AP device. 2. Configure your computer to use these settings: IP address: 192.168.1.2 Subnet mask: 255.255.255.0 Gateway: 192.168.1.1 3. In a web browser, type: https://192.168.1.1 4. Type the default password: wgwap 5. Set the IP address of the AP device to an address on the same subnet as your Firebox. Only complete this process if you do not use DHCP on your network. 简体中文 1718 如果这是您的第一台 AP 设备，您必须开启 Firebox 设备上的 Gateway Wireless Controller（无线网关控制器）。 1. 在 Policy Manager（策略管理器）或 Fireware Web UI（固件网络用户界面）上进行 Firebox 配置。 2. 选择 Network> Gateway Wireless Controller。 3. 开启 Gateway Wireless Controller。 4. 为 Firebox 设置一个用于与AP设备配对的密码短语。 5. 如果您使用 Policy Manager，将这一配置保存到 Firebox 上。 将AP设备与 Firebox 设备配对 1. 在配置 Gateway Wireless Controller 时，在 Access Points 选项卡上，点击 Refresh 以发现 AP 设备。 2. 选择未配对的 Access Point，点击 Pair。 3. 输入 AP 设备的默认密码短语：wgwap 后续步骤 要完成 WatchGuard AP 设备的配置，您需要使用 Gateway Wireless Controller： • 配置 AP 设备的无线电和安全设置。 • 创建一个或多个无线网络 SSID。 • 分配一个 SSID 给您的 AP 设备。 • 将这一配置保存到 Firebox 上。 • 在 Firebox 系统管理器或 Web UI Gateway Wireless Controller Dashboard 上确认您的 AP 设 备已联网。 欲了解更多关于如何设置您的 AP 设备的信息，请访问固件帮助文档，网址为 http://www.watchguard.com/wgrd-help/documentation/overview。 连接 WatchGuard AP 设备 1. 将以太网电缆连到 WatchGuard AP 设备的以太网接口。 2. 将以太网电缆的另一端连接到网络，或者直接连到已开启 DHCP 的受信或可选 Firebox 接口。 在连接 AP 设备时，网络或 Firebox 接口必须开启 DHCP。 如果您的网络没有使用 DHCP，在将 AP 设备连接到网络前，请按照下述方法为AP设备手动配置一个 IP 地址。 3. 如果您没有使用 PoE，请用电源适配器与 AP 设备和电源相连。 这时设备处于开机状态。当 AP 设备已准备好配对时，Power/Status 指示灯会闪烁。 将 WatchGuard AP 与 Firebox 配对 手动配置 AP 设备地址 连接到 WatchGuard AP 设备的 Web UI，给 AP 设备手动分配一个静态 IP 地址。 1. 用以太网电缆直接将您的计算机与 AP 设备相连。 2. 将您的计算机配置为使用以下设置： IP 地址：192.168.1.2 子网掩码：255.255.255.0 网关：192.168.1.1 3. 打开网络浏览器，输入：https://192.168.1.1 4. 输入默认密码：wgwap 5. 将 AP 设备的 IP 地址设置为 Firebox 设备所在子网的 IP 地址。 只有当您的网络没有使用 DHCP 时，才需要进行这一设置。 Configurez manuellement l'adresse du périphérique AP Connectez l'interface utilisateur Web du périphérique AP WatchGuard afin de lui attribuer manuellement une adresse IP statique. 1. Utilisez un câble Ethernet pour connecter directement votre ordinateur au périphérique AP. 2. Configurez votre ordinateur avec les paramètres suivants : Adresse IP : 192.168.1.2 Masque de sous-réseau : 255.255.255.0 Passerelle : 192.168.1.1 3. Dans un navigateur Web, saisissez : https://192.168.1.1 4. Saisissez le mot de passe par défaut : wgwap 5. Définissez l'adresse IP du périphérique AP sur une adresse se trouvant sur le même sous-réseau que votre Firebox. S'il s'agit de votre premier périphérique AP, vous devez activer le Gateway Wireless Controller sur le Firebox. 1. Ouvrez votre configuration Firebox dans Policy Manager ou dans l'interface utilisateur Web Fireware. 2. Sélectionnez Network > Gateway Wireless Controller. 3. Activez le Gateway Wireless Controller. 4. Définissez le mot de passe que le Firebox va utiliser pour connecter les points d'accès associés. 5. Si vous utilisez Policy Manager, enregistrez la configuration sur le Firebox. Associer le périphérique AP à votre Firebox 1. Dans la configuration Gateway Wireless Controller, dans l'onglet Access Points, cliquez sur Refresh pour afficher le périphérique AP. 2. Sélectionnez le périphérique AP non associé et cliquez sur Pair. 3. Saisissez le mot de passe par défaut du périphérique AP : wgwap Étapes suivantes Pour finaliser la configuration de votre périphérique AP WatchGuard, utilisez le Gateway Wireless Controller pour : • Configurer les paramètres radio et de sécurité du périphérique AP. • Créer un ou plusieurs SSID pour votre réseau sans fil. • Affecter le SSID à votre périphérique AP. • Enregistrer la configuration sur votre Firebox. • Assurez-vous que votre périphérique AP est en ligne dans Firebox System Mana…

Text truncated - open the document above for the full version.

Federal Authoriz 7435 O a Columbi Date: No Subject: To Who m We, the been au t Applican Address Signatu Name a E-mail Te l . Communicat ation and Ev akland Mills R a MD 21046 ovember 25, FCC Applic a m it may con undersigned thorized und nt s re and Job Title. tions Comm valuation Div Rd 6-1609 2015 ation for FCC ncern, d, would like t der the Decla : WatchG : 505 Fifth : ______ . :Lee Mic : lee.saul@ : 2066133 ission vision C ID: Q6G-A to declare th aration of Con uard Technolo h Avenue Sou ___________ hael Saul / Co @watchguard 3761 AP300 at the comp o nformity proc ogies, Inc. uth, Suite 500 __________ ompliance C d.com osite portion cedures. Seattle Washi _________ oordinator catagorized ington 98104 as compute United States r peripheral h s has

Subject: Ad FCC ID: Q6G IC: 4657A-A To Whom it We, WatchG 1. is a b freq a. b. c. 2. is n o devi Please conta Regards, Applicant Address Signature Name and J E-mail Te l . Hoc Mode F G-AP300 AP300 may concern Guard Techno ble to be ope uencies only) 802.11bgn (2 5G Band 1: 5 5G Band 4: 5 ot able to ope ice. act the one s ob Title. Function Decl n, ologies, Inc., erated on bot y) supported w 2412~2462M 5180~5240M 5745~5825M erate on non signed below : WatchGu : 505 Fifth States : ________ : Lee Micha : lee.saul@ : 20661337 laration declare tha t th master and within followi MHz；2422~2 MHz；5190~5 MHz；5755~5 -US/Canada wor the autho ard Technolo Avenue So ___________ ael Saul / Co @watchguard 761 t the device ( d client with A ing frequency 2452MHz) 5230MHz；5 5795MHz；5 frequencies orized agent f ogies, Inc. outh, Suite 5 ___________ ompliance Co .com (FCC ID: Q6G Ad Hoc Mode y bands: 5210MHz 5775MHz s, country cod for this filing. 500 Seattle ______ oordinator G-AP300 /IC e (limited to o de selection w Thank you. Washington Date: Nove C: 4657A-AP3 operate on U will be disabl n 98104 Uni mber 25, 201 300 ) US/Canada led for this ited 15

F A F P P tr 1 2 3 T p c T d S A A S J E T Federal Com Authorizatio FCC ID：Q6G Permanent C Pursuant to S reatment of i . Block D 2. Circuit D 3. Operatio The above ma public disclos competitors. The Applican documentatio Sincerely, Applicant’s co Applicant’s co Signature ob Title and E-mail Tel. C mmunication n and Evalu G-AP300 Confidentiality Sections 0.4 nformation a iagram Diagram onal Descrip aterials cont sure of thes nt understand on will not be ompany nam ompany addr Dept. Confid ns Commiss uation Divisi y Request 57 and 0.4 5 accompanyin tion ain trade se c se matters m ds that purs e made befor me ress dential sion ion 59 of the Co ng this Applic crets and pro might be har suant to Rule re the date of : WatchGu : 505 Fifth A : _______ : Lee Mich : lee.saul@ : 20661337 lity Re ommission’s cation As out oprietary info rmful to the e 0.457, di s f the Grant fo ard Technolog Avenue South ___________ hael Saul / C @watchguard.c 761 equest Rules, the A lined below: ormation not Applicant a sclosure of t or this applic gies, Inc. h, Suite 500 S __________ Compliance C com t Lette Applicant He customarily r and provide his Applicati cation eattle Washin _______ Coordinator er Da ereby reques released to t unjustified ion and all a ngton 98104 U te: 2015/11/2 sts confidenti the public. Th benefits to i accompanyin United States 25 ial he its ng

Federal 7435 O a Columbi Subject: FCC ID: Product To who m We the u for equip Sporto n Address Name Job Titl e e-mail We furt h 1.2002(b Anti-Dru This ap p applicati Applican Address Signatu Name a E-mail Te l . Communicat akland Mills R a MD 21046 Product Cer Q6G-AP300 name: Watc m it may conc undersigned, pment author n Internatio s : No. 5 2 Tao Yu : Kevin L e : Vice M : KevinL her certifies b), is subject g Abuse Ac t pointment a on as an au t nt s re and Job Title. tions Comm Rd 6-1609 rtification Re 0 chGuard® AP cern: , hereby auth rization of mo nal Inc. 2, Hwa Ya 1s uan City, Taiw Liang Manager Liang@sporto that neither to a denial t o t of 1998, 21 lso include s thorized age : WatchG : 505 Fifth : ______ . :Lee Mic : lee.saul@ : 2066133 ission presentativ e P horize followi odel AP300 t Rd., Hwa Y wan, R.O.C. on.com.tw the applica n o Federal be U.S.C. 835( s the author nt. uard Technolo h Avenue Sou ___________ hael Saul / Co @watchguard 3761 e Authorizatio ing person to to the FCC R Ya Technolog nt nor any p enefits, that in (a). rity to comp ogies, Inc. uth, Suite 500 __________ ompliance C d.com on Letter o act as our a Rules and Re gy Park, Kwe party to this nclude FCC plete FCC F Seattle Washi _________ oordinator agent in the p egulations. ei-Shan Distri application, benefits, pu r Form 731 on ington 98104 D preparation o ict, as defined rsuant to sec n our behal United States ate: 2015/11 of an applicat in 47 CFR ction 5301 of f and sign s /25 tion Ch. the the

Report No. : EP582836 SPORTON International Inc. Page Number : B1 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 APPENDIX B. Photographs of EUT Report No. : EP582836 SPORTON International Inc. Page Number : B2 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

AP300 EN60950-1 277-4256-300 Rev A 277-4256-300 Rev A Q6G-AP300 4657A-AP300

Report No. : EP582836 SPORTON International Inc. Page Number : B3 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B4 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B5 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B6 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B7 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B8 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B9 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B10 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B11 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B12 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B13 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B14 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Report No. : EP582836 SPORTON International Inc. Page Number : B15 of B15 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

Maximum Permissible Exposure Report No. : FA582836 SPORTON INTERNATIONAL INC. Page No. : 1 of 6 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Maximum Permissible Exposure Equipment : WatchGuard® AP Brand Name : WatchGuard® Model No. : AP300 FCC ID : Q6G-AP300 Standard : ANSI/IEEE C95.1 Applicant : WatchGuard® Technologies, Inc. 505 Fifth Avenue South, Suite 500 Seattle Washington 98104 United States Manufacturer : Senao Networks, Inc. No. 500 & 528, Fusing 3rd Rd., Hwa-Ya Technical Park, Kuei-Shan Dist., Taoyuan City, Taiwan, R.O.C. The product sample received on Jun. 18, 2014 and completely tested on Oct. 12, 2015. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI/IEEE C95.1 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Kevin Liang / Assistant Manager Maximum Permissible Exposure Report No. : FA582836 SPORTON INTERNATIONAL INC. Page No. : 2 of 6 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Table of Contents 1 HUMAN EXPOSURE ASSESSMENT ................................................................................................... 4 1.1 Maximum Permissible Exposure ............................................................................................................ 4 Maximum Permissible Exposure Report No. : FA582836 SPORTON INTERNATIONAL INC. Page No. : 3 of 6 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Revision History Report No. Version Description Issued Date FA582836 Rev. 01 Initial issue of report Nov. 09, 2015 Maximum Permissible Exposure Report No. : FA582836 SPORTON INTERNATIONAL INC. Page No. : 4 of 6 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1 Human Exposure Assessment 1.1 Maximum Permissible Exposure 1.1.1 Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f 2 )* 6 30-300 61.4 0.163 1.0 6 300-1500 - - F/300 6 1500-100,000 - - 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 - - F/1500 30 1500-100,000 - - 1.0 30 Note 1: f = frequency in MHz ; *Plane-wave equivalent power density Note 2: For the applicable limit, see FCC 1.1310 1.1.2 MPE Calculation Method E (V/m) = d GP30 Power Density: Pd (W/m 2 ) = 377 E 2 E = Electric field (V/m) P = RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 d377 GP30   Maximum Permissible Exposure Report No. : FA582836 SPORTON INTERNATIONAL INC. Page No. : 5 of 6 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1.1.3 Result of Maximum Permissible Exposure RF General Information 2400 MHz – 2483.5 MHz Frequency Range (MHz) IEEE Std. 802.11 Protocol Ch. Frequency (MHz) Channel Number Number of Transmit Chains (N TX ) RF Output Power (dBm) 2400-2483.5 b 2412-2462 1-11 [11] 3 24.10 2400-2483.5 g 2412-2462 1-11 [11] 3 22.08 2400-2483.5 n (HT20) 2412-2462 1-11 [11] 3 21.97 2400-2483.5 n (HT40) 2422-2452 3-9 [7] 3 20.47 Note 1: RF output power specifies that Maximum Conducted (Average) Output Power. RF General Information 5150~5250MHz Frequency Range (MHz) IEEE Std. 802.11 Protocol Ch. Frequency (MHz) Channel Number Number of Transmit Chains (N TX ) RF Output Power (dBm) 5150-5250 a 5180-5240 36-48 [4] 3 24.52 5150-5250 n (HT20) 5180-5240 36-48 [4] 3 24.89 5150-5250 n (HT40) 5190-5230 38-46 [2] 3 26.09 5150-5250 ac (VHT20) 5180-5240 36-48 [4] 3 24.97 5150-5250 ac (VHT40) 5190-5230 38-46 [2] 3 26.01 5150-5250 ac (VHT80) 5210 42 [1] 3 21.61 Note 1: RF output power specifies that Maximum Conducted (Average) Output Power. RF General Information 5725 MHz – 5850 MHz Frequency Range (MHz) IEEE Std. 802.11 Protocol Ch. Frequency (MHz) Channel Number Number of Transmit Chains (N TX ) RF Output Power (dBm) 5725-5850 a 5745-5825 149-165 [5] 3 25.98 5725-5850 n(HT20) 5745-5825 149-165 [5] 3 26.00 5725-5850 n(HT40) 5755-5795 151-159 [2] 3 26.17 5725-5850 ac(VHT20) 5745-5825 149-165 [5] 3 26.05 5725-5850 ac(VHT40) 5755-5795 151-159 [2] 3 26.09 5725-5850 ac(VHT80) 5775 155 [1] 3 19.18 Note 1: RF output power specifies that Maximum Conducted (Average) Output Power. Maximum Permissible Exposure Report No. : FA582836 SPORTON INTERNATIONAL INC. Page No. : 6 of 6 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Worst Maximum RF Output Power Result Exposure Environment General Population / Uncontrolled Exposure Separation Distance (cm) 22 Condition RF Output Power (dBm) Modulation Mode N TX Chain Port 1 Chain Port 2 Chain Port 3 Sum Chain DG (dBi) EIRP Power PD (S) (mW/cm²) 11b 3 19.42 19.10 19.45 24.10 8.72 32.82 0.31476 n(HT40) 5725-5850 3 21.42 20.98 21.74 26.17 9.62 35.79 0.62397 Co-location Total 0.93873 Maximum Permissible Exposure Limit (mW/cm²) 1 Note 1: N TX = Number of Transmit Chains

FCC Test Report Report No. : FR582836 SPORTON INTERNATIONAL INC. Page No. : 1 of 8 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1 CO-LOCATION 1.1 Transmitter Radiated Unwanted Emissions 1.1.1 Transmitter Radiated Unwanted Emissions Limit Restricted Band Emissions Limit Frequency Range (MHz) Field Strength (uV/m) Field Strength (dBuV/m) Measure Distance (m) 0.009~0.490 2400/F(kHz) 48.5 - 13.8 300 0.490~1.705 24000/F(kHz) 33.8 - 23 30 1.705~30.0 30 29 30 30~88 100 40 3 88~216 150 43.5 3 216~960 200 46 3 Above 960 500 54 3 Note 1: Test distance for frequencies at or above 30 MHz, measurements may be performed at a distance other than the limit distance provided they are not performed in the near field and the emissions to be measured can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade (inverse of linear distance for field-strength measurements, inverse of linear distance-squared for power-density measurements). Note 2: Test distance for frequencies at below 30 MHz, measurements may be performed at a distance closer than the EUT limit distance; however, an attempt should be made to avoid making measurements in the near field. When performing measurements below 30 MHz at a closer distance than the limit distance, the results shall be extrapolated to the specified distance by either making measurements at a minimum of two or more distances on at least one radial to determine the proper extrapolation factor or by using the square of an inverse linear distance extrapolation factor (40 dB/decade). The test report shall specify the extrapolation method used to determine compliance of the EUT. Un-restricted Band Emissions Limit RF output power procedure Limit (dB) Peak output power procedure 20 Average output power procedure 30 Note 1: If the peak output power procedure is used to measure the fundamental emission power to demonstrate compliance to requirements, then the peak conducted output power measured within any 100 kHz outside the authorized frequency band shall be attenuated by at least 20 dB relative to the maximum measured in-band peak PSD level. Note 2: If the average output power procedure is used to measure the fundamental emission power to demonstrate compliance to requirements, then the power in any 100 kHz outside of the authorized frequency band shall be attenuated by at least 30 dB relative to the maximum measured in-band average PSD level. FCC Test Report Report No. : FR582836 SPORTON INTERNATIONAL INC. Page No. : 2 of 8 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1.1.2 Test Procedures Test Method Measurements may be performed at a distance other than the limit distance provided they are not performed in the near field and the emissions to be measured can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade (inverse of linear distance for field-strength measurements, inverse of linear distance-squared for power-density measurements). The average emission levels shall be measured in [duty cycle ≥ 98 or duty factor]. For the transmitter unwanted emissions shall be measured using following options below: Refer as FCC KDB 558074, clause 11 for unwanted emissions into non-restricted bands. Refer as FCC KDB 558074, clause 12 for unwanted emissions into restricted bands. Refer as FCC KDB 558074, clause 12.2.5.1 and 9.2.1 Option 1 (spectral trace averaging) Refer as FCC KDB 558074, clause 12.2.5.2 and 9.2.1 Option 2 (slow sweep speed). Refer as ANSI C63.10, clause 4.1.4.2.3 (Reduced VBW). VBW ≥ 1/T, where T is pulse time. Refer as ANSI C63.10, clause 4.1.4.2.4 average value of pulsed emissions. Refer as FCC KDB 558074, clause 12.2.4 and 9.1.1 measurement procedure peak limit. Refer as FCC KDB 558074, clause 12.2.3 measurement procedure Quasi-Peak limit. For radiated measurement, refer as FCC KDB 558074, clause 12.1. Refer as ANSI C63.10, clause 6.4 for radiated emissions below 30 MHz and test distance is 3m. Refer as ANSI C63.10, clause 6.5 for radiated emissions 30 MHz to 1 GHz and test distance is 3m. Refer as ANSI C63.10, clause 6.6 for radiated emissions above 1 GHz and test distance is 3m. For conducted and cabinet radiation measurement, refer as FCC KDB 558074, clause 12.2.2. For conducted unwanted emissions into non-restricted bands (relative emission limits). Devices with multiple transmit chains: Refer as FCC KDB 662911, when testing out-of-band and spurious emissions against relative emission limits, tests may be performed on each output individually without summing or adding 10 log(N) if the measurements are made relative to the in-band emissions on the individual outputs. For conducted unwanted emissions into restricted bands (absolute emission limits). Devices with multiple transmit chains using options given below: (1) Measure and sum the spectra across the outputs or (2) Measure and add 10 log(N) dB FCC Test Report Report No. : FR582836 SPORTON INTERNATIONAL INC. Page No. : 3 of 8 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1.1.3 Test Setup Transmitter Radiated Unwanted Emissions (below 1GHz) Magnetic field tests shall be performed in the frequency range of 9 kHz to 30 MHz using a calibrated loop antenna. Electric field tests shall be performed in the frequency range of 30 MHz to 1000 MHz using a calibrated bi-log antenna. Transmitter Radiated Unwanted Emissions (Above 1GHz) Electric field tests shall be performed in the frequency range of 1 GHz to 10th harmonic of highest fundamental frequency or 40 GHz using a calibrated horn antenna. 1.1.4 Transmitter Radiated Unwanted Emissions (Below 30MHz) All amplitude of spurious emissions that are attenuated by more than 20 dB below the…

Text truncated - open the document above for the full version.

FCC Test Report Report No. : FR582836AN SPORTON INTERNATIONAL INC. Page No. : 1 of 98 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 FCC Test Report Equipment : WatchGuard® AP Brand Name : WatchGuard® Model No. : AP300 FCC ID : Q6G-AP300 Standard : 47 CFR FCC Part 15.407 Operating Band : 5150 MHz – 5250 MHz 5725 MHz – 5850 MHz FCC Classification : NII Applicant : WatchGuard® Technologies, Inc. 505 Fifth Avenue South, Suite 500 Seattle Washington 98104 United States Manufacturer : Senao Networks, Inc. No. 500 & 528, Fusing 3rd Rd., Hwa-Ya Technical Park, Kuei-Shan Dist., Taoyuan City, Taiwan, R.O.C. Function : Outdoor AP; Indoor AP; Fixed P2P AP Portable Client The product sample received on Jun. 18, 2014 and completely tested on Oct. 12, 2015. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2013 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Kevin Liang / Assistant Manager FCC Test Report Report No. : FR582836AN SPORTON INTERNATIONAL INC. Page No. : 2 of 98 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Support Equipment ................................................................................................................................. 8 1.3 Testing Applied Standards ..................................................................................................................... 8 1.4 Testing Location Information .................................................................................................................. 8 1.5 Measurement Uncertainty ...................................................................................................................... 9 2 TEST CONFIGURATION OF EUT ....................................................................................................... 10 2.1 The Worst Case Modulation Configuration .......................................................................................... 10 2.2 The Worst Case Power Setting Parameter .......................................................................................... 10 2.3 The Worst Case Measurement Configuration ...................................................................................... 11 2.4 Test Setup Diagram ............................................................................................................................. 13 3 TRANSMITTER TEST RESULT .......................................................................................................... 15 3.1 AC Power-line Conducted Emissions .................................................................................................. 15 3.2 Emission Bandwidth ............................................................................................................................. 18 3.3 RF Output Power .................................................................................................................................. 22 3.4 Peak Power Spectral Density ............................................................................................................... 26 3.5 Transmitter Bandedge Emissions ........................................................................................................ 30 3.6 Transmitter Unwanted Emissions ......................................................................................................... 34 3.7 Frequency Stability ............................................................................................................................... 95 4 TEST EQUIPMENT AND CALIBRATION DATA ................................................................................ 97 A PPENDIX A. TEST PHOTOS APPENDIX B. PHOTOGRAPHS OF EUT FCC Test Report Report No. : FR582836AN SPORTON INTERNATIONAL INC. Page No. : 3 of 98 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Summary of Test Result Conformance Test Specifications Report Clause Ref. Std. Clause Description Result 1.1.2 15.203 Antenna Requirement Complied 3.1 15.207 AC Power-line Conducted Emissions Complied 3.2 15.407(a) Emission Bandwidth Complied 3.3 15.407(a) RF Output Power (Maximum Conducted Output Power) Complied 3.4 15.407(a) Peak Power Spectral Density Complied 3.5 15.407(b) Transmitter Bandedge Emissions Complied 3.6 15.407(b) Transmitter Unwanted Emissions Complied 3.7 15.407(g) Frequency Stability Complied FCC Test Report Report No. : FR582836AN SPORTON INTERNATIONAL INC. Page No. : 4 of 98 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Revision History Report No. Version Description Issued Date FR582836AN Rev. 01 Initial issue of report Nov. 09, 2015 FCC Test Report Report No. : FR582836AN SPORTON INTERNATIONAL INC. Page No. : 5 of 98 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1 General Description 1.1 Information 1.1…

Text truncated - open the document above for the full version.