QC8-RDL3000RMEAdvanced Broadband Wireless Infrastructure Solution

RDL-3000 M2M Solutions 70-00184-05-00 Proprietary Redline Communications © 2015 Page 1 of 28 July 17, 2015 RDL-3000 Family Broadband Wireless Systems RDL-3000-RME Radio Module Product Manual 1 Product Overview ................................................................... 5 2 Conditions of Use ................................................................... 6 3 Module Installation and Service ............................................ 8 4 Final Product Requirements ................................................ 10 5 Regulatory Notices ............................................................... 24 RDL-3000-RME PRODUCT MANUAL 70-00184-05-00 Proprietary Redline Communications © 2015 Page 2 of 28 July 17, 2015 Copyright Information All rights reserved June 19, 2015. The information in this document is proprietary to Redline Communications Inc. This document may not in whole or in part be copied, reproduced, or reduced to any medium without prior consent in writing from Redline Communications Incorporated. Contact Information Contact Information: Redline Communications Inc. 302 Town Centre Blvd. Markham, ON Canada L3R 0E8 Web site: http://www.rdlcom.com Email: Inquiries: [email protected] Support: [email protected] Training: [email protected] Document Control: 70-00184-05-00-RDL-3000-RME_Module_Product_Manual-20150717a.doc Disclaimer The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Additionally, Redline makes no representations or warranties, either expressed or implied, regarding the contents of this product. Redline Communications shall not be liable for any misuse regarding this product. The information in this document is subject to change without notice. No part of this document shall be deemed to be part of any warranty or contract unless specifically referenced to be part of such warranty or contract within this document. RDL-3000-RME PRODUCT MANUAL 70-00184-05-00 Proprietary Redline Communications © 2015 Page 3 of 28 July 17, 2015 TABLE OF CONTENTS 1 Product Overview ................................................................... 5 RDL-3000-RME ............................................................................................... 5 2 Conditions of Use ................................................................... 6 2.1 General Conditions ............................................................................................ 6 2.2 Country of Use ................................................................................................... 6 RDL-3000-RME ............................................................................................... 6 2.3 Product Labeling ................................................................................................ 7 2.3.1 Module Label .................................................................................................... 7 RDL-3000-RME ............................................................................................... 7 2.3.2 External Label ................................................................................................... 7 RDL-3000-RME ............................................................................................... 7 3 Module Installation and Service ............................................ 8 3.1 Installation into a Final Product ........................................................................ 8 3.2 Module Servicing ............................................................................................... 8 3.3 Professional Installation .................................................................................... 9 3.4 Safety Precautions ............................................................................................. 9 3.5 Radio Frequency Safety .................................................................................... 9 4 Final Product Requirements ................................................ 10 4.1 RDL-3000-RME ................................................................................................. 10 4.1.1 Frequency Bands ............................................................................................ 10 4.1.2 Antenna Use and Transmit Power ................................................................... 10 4.1.3 Certified Antennas .......................................................................................... 10 4.1.4 Power & EIRP (MIMO Operation) .................................................................... 11 Operation at FCC 2496-2690 MHz Band ....................................................... 11 Operation at IC 2305-2320 MHz and IC 2345-2360 MHz Bands .................... 15 Operation at 2400-2483.5 MHz Band (Canada Only) .................................... 22 5 Regulatory Notices ............................................................... 24 5.1.1 FCC Notices ................................................................................................... 24 5.2 Industry Canada Notices: Deployment in Canada ......................................... 26 RDL-3000-RME PRODUCT MANUAL 70-00184-05-00 Proprietary Redline Communications © 2015 Page 4 of 28 July 17, 2015 LIST OF TABLES Table 1: RDL-3000-RME: Approved Antennas for IC ..................................................... 10 Table 2: RDL-3000-RME: Approved Antennas for FCC ................................................. 10 Table 3: 2.5 GHz: RF Power & EIRP: 1.25 MHz channel: all 15 dBi antennas for FCC . 11 Table 4: 2.5 GHz: RF Power & EIRP: 1.25 MHz channel: all 16 dBi antennas for FCC . 11 Table 5: 2.5 GHz: RF Power & EIRP: 1.25 MHz channel: all 27 dBi antennas for FCC . 11 Table 6: 2.5 GHz: RF Power & EIRP: 2.5 MHz channel: all 15 dBi antennas for FCC ... 12 Table 7: 2.5 GHz: RF Power & EIRP: 2.5 MHz channel: all 16 dBi antennas for…

Text truncated - open the document above for the full version.

June 11, 2015 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Applicant: Redline Communications Inc. FCC ID: QC8-RDL3000RME RE: Limited Modular Transmitter Approval for RDL-3000-RME To whom it may concern: Pursuant to the FCC Rules, Part 15 Section 15.212 Modular transmitters and 996369 D01 Module Equip Auth Guide v01r04, Redline Communications, Inc. hereby requests Limited Modular Transmitter Approval for the above listed FCC submittal. This letter affirms that Redline Communications Inc. shall retain complete control over the final installation of the module and will ensure compliance of the end product to all applicable FCC regulations. The module will not be distributed, marketed or sold to the general public and Redline will not make this module available as standalone product. It will be installed in the devices produced by Redline Communications Inc. and its authorized partners. According to the requirements of section 15.212 of FCC rules please note the following statements: 1. Limited Modular Transmitter Approval is being requested since the modular transmitter doesn’t have its own RF shielding. The module has been tested in a stand- alone configuration and complies with all of the FCC requirements at the module level. 2. The input to the module is an Ethernet interface. All modulation and protocol elements are contained within module. There are no other modulation or data inputs to the module that may result in non-compliant operation. 3. The modular transmitter has its own power supply regulation and filtering. 4. The modular transmitter complies with the antenna requirements of Section 15.203 and 15.204(c). The module does not incorporate an integrated antenna, however uses unique MCX RF connectors for antenna connection. The module has been tested with the intended antenna. Approval for additional antenna will be obtained through a Class II permissive change. The modular transmitter will be installed by professional installers trained by Redline Communications. Redline Communications will retain complete control over the final installation of the module ensuring that only approved antenna type will be used with this module. The list of approved antennas is included in the user manual. 5. The modular transmitter has been tested in a stand-alone configuration. It complies with Part 27 regardless of the device / enclosure into which it will be installed. 6. The modular transmitter will be labeled with its own FCC ID: QC8-RDL3000RME, and the chassis of the device / enclosure into which the module is installed will display a label referring to the enclosed module “Contains FCC ID: QC8-RDL3000RME”. 7. The modular transmitter operates in 2496-2690MHz band under Part 27 to which it has been tested. Users do not have access to controls that may cause the module to operate outside its normal mode of operation. 8. The modular transmitter has been evaluated with the intended antenna and complies with all applicable RF exposure requirements. RF exposure warnings and separation distances are included in the user manual. Sincerely, Rod Cronin AVP, Product Management Ph: 905.479.8344 x2377 [email protected]

July 24, 2015 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: Justification for requesting internal photos confidentiality Applicant: Redline Communications Inc. Model: RDL-3000-RME FCC ID: QC8-RDL3000RME Dear Sir / Madam, Redline Communications Inc. would like to request that internal photos are held confidential and not available to public viewing. The RDL-3000-RME is limited modular transmitter that will not be distributed, marketed or sold to the general public and Redline will not make this module available as standalone product. It will be installed in the devices /enclosures produced by Redline Communications Inc. and its authorized partners. It is only serviceable by Redline Communications or its designated technicians. The final product containing RDL-3000-RME module will be sold to customers for highly confidential and secure industrial, military and public safety applications. We feel that this information is considered as sensitive and creates a vulnerability to customers deploying this product. This request for confidentiality is made under the provisions of Section 0.457(d) of the Commission's Rules, and Section 552(b)(4) of the Freedom of Information Act. These sections authorize withholding from public inspection materials which would be privileged as a matter of law if retained by the person submitting them, and materials which would not customarily be released to the public by that person. Sincerely, Rod Cronin AVP Product Management Ph: 905.479.8344 x2377 [email protected] Page 1 of 1

1 CONFIDENTIALITY AGREEMENT This Confidentiality Agreement (“Agreement”) is made and entered into by and between Redline Communications Inc. (“RCI”), a Canadian corporation, located at 302 Town Centre Blvd. 4 th floor, Markham, Ontario, L3R 0E8 together with and on behalf of its various affiliated companies, and (“Company”), (insert name and address as well as Country of incorporation) Witnesseth: WHEREAS, RCI and Company desire to explore and discuss the potential mutual benefits from joint business arrangements or activities which explorations and discussions are herein referred to as the “Discussions”; AND WHEREAS, in connection with the Discussions, RCI and Company will acquire certain confidential information relating to each other’s businesses, including, without limitation, technical information such as internal photos, know-how, business methods and processes; AND WHEREAS, RCI and Company desire to set forth their understanding with respect to such confidential information during and after the Discussions; NOW THEREFORE for valuable consideration (the receipt and sufficiency of which is hereby acknowledged) RCI and Company agree as follows: 1. Confidential Information. “Confidential Information” shall mean any business, marketing, sales, financial (including pricing) or technical information, including, without limitation, any information relating to present or future business affairs, operations, methods, techniques, operations, financial condition, reports, research, product plans, products, developments, processes, models, designs, drawings, formulae, markets, software (including source and object code), algorithms, business plans or agreements with third parties and all other information of any kind which may reasonably be deemed confidential or proprietary, disclosed by one party (the “Disclosing Party”) to the other (the “Receiving Party”), whether such information is in written, oral, graphic or machine-readable form and which is designated or identified as “confidential”, “proprietary” or in some other manner prior to the disclosure, to indicate its confidential nature. Oral disclosures will be confirmed in written format 30 days following the disclosure. Notwithstanding the foregoing, “Confidential Information” shall not include information which: (a) has been or becomes published or is now or is in the future in the public domain through no action of the Receiving Party; (b) prior to disclosure hereunder, is within the legitimate possession of the Receiving Party as evidenced by competent written proof; (c) subsequent to disclosure hereunder, is lawfully received from a third party having rights therein without restriction of the third party’s rights to disseminate the information and without notice of any restriction against its further disclosure; or (d) is independently developed or acquired by the Receiving Party through persons who have not had, either directly or indirectly, access to or knowledge of such Confidential Information. 2. Nondisclosure. The Confidential Information shall (a) be kept confidential by the Receiving Party and not disclosed to any third parties, (b) not be used by the Receiving Party in any way detrimental to the Disclosing Party, and (c) not be used other than in connection with the Discussions. The Receiving Party may disclose the Confidential Information to its and its affiliates’ directors, officers, employees, consultants and agents (collectively, “Representatives”) only if such Representatives need to know the Confidential Information in connection with the Discussions and are bound by confidentiality obligations similar to those contained herein. The Receiving Party shall (i) inform each of its Representatives receiving Confidential Information of the confidential nature of the Confidential Information and of this Agreement, (ii) direct its Representatives to treat the Confidential Information confidentially and not to use it other than in connection with the Discussions, and (iii) be responsible for any improper use of the Confidential Information by the Receiving Party or its Representatives. Without the prior written consent of the Disclosing Party, the Receiving Party will Redline Communications Inc. | Confidentiality Agreement 2 not, and will direct its Representatives not to, disclose to any person that the Confidential Information has been made available to it or that the Discussions are taking place. 3. Care and Return of Confidential Information. The Receiving Party shall provide at least the same care to avoid disclosure or unauthorized use of the Confidential Information as it generally provides to protect its own proprietary information, which shall, in all events, equal or exceed a standard and level of care generally recognized as being reasonable for the protection of highly confidential information. All Confidential Information shall be retained by the Receiving Party in a place with access limited only to the Receiving Party’s Representatives who reasonably need to know the Confidential Information in connection with the Discussions. Upon the request of the Disclosing Party, the Receiving Party shall destroy or return to the Disclosing Party, or in the case of electronic, magnetic or digital media, at the election of the Disclosing Party, erase or render unreadable, all materials furnished which contain Confidential Information of the Disclosing Party, including, without limitation, documents, drawings, models, prototypes, sketches, designs, lists, papers, magnetic media and other tangible media. 4. No Licenses. Neither the execution of this Agreement nor the furnishing of any information under this Agreement shall be construed as granting any party or any of its Representatives, either expressly or by implication, any license or right to use any Confidential Information for its own benefit or the benefit of any other person, firm or entity, and each party expressly agrees not to so use any such information. Nothing …

Text truncated - open the document above for the full version.

Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent FCC On our behalf, I appoint Jenny Gibbs of Nemko Canada, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides Redline Communications, 302 Town Center Blvd, Markham, Ontario, L3R 0E8 Dated this 18 Day of June 20 15 Agency agreement expiration date: June 31, 2016 By: Rod Cronin Signature Printed Title: AVP Product Management On behalf of : Redline Communications Inc. Telephone: 905.479.8344 x2377

Page 1 of 1 June 11, 2015 Applicant: Redline Communications Inc. FCC ID: QC8-RDL3000RME Model: RDL-3000-RME MIMO Mode Declaration We, Redline Communications Inc, declare that RDL-3000-RME Advanced Broadband Wireless Infrastructure Solutions, Model: RDL-3000-RME, FCC ID: QC8-RDL3000RME, when operates in MIMO A (STBC/STC) mode or MIMO B (spatial multiplexing) modes, the only modes in which it transmits from both antennas, the transmitter output signals are completely uncorrelated. Sincerely, Rod Cronin AVP Product Management Ph: 905.479.8344 x2377 [email protected]

July 16, 2015 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: QC8-RDL3000RME Product Name: RDL-3000-RME Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions’ rules, we hereby request that the following documents be held confidential: Block diagrams Schematic diagrams Parts List System overview Internal photos These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. If you have any queries, please do not hesitate to contact Sincerely, Dated this 16 Day of July 2015 By: Rod Cronin Signature Printed Title: AVP Product Management Telephone: 905-479-8344 x2377 Applicant: Redline Communications Inc

June 24, 2015 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: External Photos Applicant: Redline Communications Inc. Model: RDL-3000-RME FCC ID: QC8-RDL3000RME Dear Sir / Madam, This submission is for limited modular approval therefore the external and internal photos are the same. Sincerely, Rod Cronin AVP Product Management Ph: 905.479.8344 x2377 [email protected] Page 1 of 1

50-01033-30 rev01 – Label, PCB, 2.3-2.7GHz R4, 1.0" x 0.5" POD
   
  
 
  !"  #$% " &%' ()*(+*" &%,-  &'.,'&/  ' "!'% " A B REVIORY   
)'''FCCID"'% "g'&' % #
/6/
8 REVDECRIIOND)E  0.5 inch 1.0 inch

Page 1 of 1 To Whom It May Concern FCC ID: QC8-RDL3000RME Model: RDL-3000-RME This is to certify that our RDL-3000-RME system does not need any Tune-up procedure over the power range, or at specific operating power levels when operating in the band 2496-2690MHz If you have any questions, please contact the undersigned. Dated this 11 Day of June 2015 By: Rod Cronin Signature Printed Title: AVP Product Management Telephone: 905-479-8344x2377 Applicant: Redline Communications Inc

Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 where:S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Maximum peak output power at device output terminal:26.70dBm Cable and Jumper loss:0.0dB Maximum peak output power at antenna input terminal:26.70dBm 467.7351413mW Single Antenna gain (typical):27dBi Number of Antennae:1 Total Antenna gain (typical):27dBi 501.1872336(numeric) Prediction distance:140cm Prediction frequency:2688.75MHz MPE limit for uncontrolled exposure at prediction frequency:1mW/cm 2 Power density at prediction frequency:0.951774 mW/cm 2 9.517745W/m 2 Tx On time:1.000000ms Tx period time:1.000000ms Average Factor:100.000000% Average Power density at prediction frequency:9.517745W/m 2 Maximum allowable antenna gain:27.21465935dBi Margin of Compliance:0.214659354dB 2 4R PG S   ONE WORLDOURAPPROVAL

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by the Standards Council of Canada. The tests included in this report are within the scope of this accreditation FCC Part 27; Date: May 2015 SCC Accredited LAB LAB Accrédité CCN TM ONE WORLDOURAPPROVAL Test report 287905-1TRFWL Date of issue: July 22, 2015 Applicant: Redline Communications Product: Broad-band wireless infrastructure product Model: RDL-3000-RME FCC ID: QC8-RDL3000RME Specifications:  FCC 47 CFR Part 27 Miscellaneous Wireless Communications Services Report reference ID: 287905-1TRFWL Page 2 of 39 Test location Company name Nemko Canada Inc. Address 303 River Road City Ottawa Province Ontario Postal code K1V 1H2 Country Canada Telephone +1 613 737 9680 Facsimile +1 613 737 9691 Toll free +1 800 563 6336 Website www.nemko.com Site number FCC: 176392 (3 m semi anechoic chamber) Tested by Andrey Adelberg, Senior Wireless/EMC Specialist Reviewed by Kevin Rose, Wireless/EMC Specialist Review date July 22, 2015 Reviewer signature Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contain in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: 287905-1TRFWL Page 3 of 39 Table of contents Table of contents .......................................................................................................................................................................................................... 3 Section 1. Report summary ................................................................................................................................................................................. 4 1.1 Applicant and manufacturer .................................................................................................................................................................................... 4 1.2 Test specifications .................................................................................................................................................................................................... 4 1.3 Statement of compliance ......................................................................................................................................................................................... 4 1.4 Exclusions ................................................................................................................................................................................................................. 4 1.5 Test report revision history ...................................................................................................................................................................................... 4 Section 2. Summary of test results ....................................................................................................................................................................... 5 2.1 FCC Part 27 test results ............................................................................................................................................................................................ 5 Section 3. Equipment under test (EUT) details ..................................................................................................................................................... 6 3.1 Sample information .................................................................................................................................................................................................. 6 3.2 EUT information ....................................................................................................................................................................................................... 6 3.3 Technical information .............................................................................................................................................................................................. 6 3.4 Product description and theory of operation ........................................................................................................................................................... 6 3.5 EUT exercise details .................................................................................................................................................................................................. 6 3.6 EUT setup diagram ................................................................................................................................................................................................... 7 3.7 EUT sub assemblies .................................................................................................................................................................................................. 7 Section 4. Engineering considerations .................................................................................................................................................................. 8 4.1 Modifications incorporated in the EUT...................................................................................…

Text truncated - open the document above for the full version.