QDYWT-200NFWIRELESS TRANSMITTER

Wireless Transmitter ■ Wireless Transmitter (WT-200NF) Thank you for purchasing our product. Please read carefully the instruction guide to use the product more safely and effectively. This is a wireless transmitter which receives the detection signal from emergency switch, remote controller or sensors and send the signal to receiver (WR-200,WR-300) ■ Product component 1 wireless transmitter, 1 adaptor, 2 screws, 1 manual ■ How to input a code After plugging the power, press the transmitter power ON switch using ball pen or sharp pin then the red light will blink. At this moment (within 8 seconds), press the ‘security’ button of the remote control more than 2 seconds, then code can be inputted lighting the red lamp. ※ Master remote control: Operate all wireless transmitter (If input a code of master remote control to each transmitter) ※ Remote control: Operate only one registered transmitter (Input a code of remote control each transmitter) ※ Input a code number of remote control to receiver ※ Input maximum 254 different codes and display location of transmitter based on the each code ■ How to set up waiting time (Motion sensor, Door sensor) 1) If the code is inputted by “Armed” button on remote control: When it receives radio waves, immediately sends radio waves. 2) If the code is inputted by “Off” button on remote control: When it receives radio waves, sends radio waves after 16seconds. ■ How to install Although range is 800m between transmitter and receiver, decrease receive range because some obstacle if it is installed in a house or building. Therefore, position a transmitter and check operation several times before installation. ※ Range of radio wave depends on structure inside building and ambient temperature (Wall, Floor, furniture, furnishing and etc.) ※ Installation location of transmitter please install 70% of distance which can be received signals(Field Test) (Example: If the signals can be received 70m between transmitter and receiver, place it 50m) ■ How to input a operating distance WT-200NF has function t hat it is operated by emergency signal of master remote control within pre-inputted operating distance and it only operates the nearest transmitter if it uses with several transmitters. (Operating distance is inputted by special remote control) After plugging the power, press “Emergency” button of special remote control (within 8 seconds) from a distance you are wanted as shown in the picture After input operating distance, Emergency signal of special remote control is possible to operate within pre- operated distance ( ※ Caution: It may not operate in a building because of obstacles within operating distance .) ■ Operation Armed – Press the “ARMED” button of a remote control for 2seconds, it makes sound “beep - beep” and blinks red lamp every seconds for 32 seconds and turn off the red lamp. OFF - Press the “OFF” button of a remote control more than 1 second, it makes a “beep” and turn on red lamp EMERGENCY - Press the “EMERGENCY” button more than 1 second of a remote control, It makes sound “beep-beep-beep” and transmits emergency signal ARMED + OFF – Press the “ARMED and OFF” button of a remote control, It makes sound “beep” and transmits signal ［ Operation after received detected signal of optional sensor ］ - Emergency button of remote control, Fire detection sensor, Gas sensor: When emergency or sensor signal is received, immediately transmits the signal to the receiver. - Motion sensor, Door sensor: If transmitter is armed - when signal is received, it transmits the signal to the receiver after 16 seconds (or immediately) ※ If transmitter is OFF, it does not receive a signal ■ Connect and operate with wired siren (option) - Emergency button of remote control, Fire detection sensor, Gas sensor: When emergency or sensor signal is received, immediately ring the siren for 32 seconds. - Motion sensor, Door sensor: If transmitter is armed - when signal is received, ring the siren for 32 seconds after 16 seconds (or immediately) ■ Product specification - Transmission distance: approximately 200m ~ 800m (depend on obstacle) - Power supply: dc 12v power adapter - Size: 112mm x 66mm x 20mm, - Weight : 77g ■ Option Remote control, Emergency switch, wired siren, pendant emergency switch, door sensor, smoke sensor, gas sensor, motion sensor. ■ Warning Change or modifications not expressly approved by manufacturer could void the user ’ s authority operate the equipment. Switch WR-200 WT-200NF RC-200F Remote control WT-200NF Operating distance: Maximum 15m

Menix Co., Ltd. 539, Yongsan-dong, Yuseong-gu, Daejeon, 305-500, Korea Tel: +82-42-930-9478, Fax: +82-42-934-6245 Date: June 10, 2010 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 This authorization is valid until further written notice from the applicant. Sincerely Yours, _________________________ Mr. GYU-CHEOL KIM / Manager Menix Co., Ltd. Tel: +82-42-930-9478 Fax: +82-42-934-6245 E-Mail: [email protected]

Menix Co., Ltd. 539, Yongsan-dong, Yuseong-gu, Daejeon, 305-500, Korea Tel: +82-42-930-9478, Fax: +82-42-934-6245 Date: June 10, 2010 FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Attention: Application Examiner Reviewing Engineer Re: Request for confidentiality per Section 0.459 of FCC Rules Applicant: Menix Co., Ltd. FCC ID: QDYWT-200NF To whom it may concern, Request is hereby submitted, on behalf of my client, Menix Co., Ltd., to withhold from public review certain portions of the application for equipment certification for the referenced FCC identifier. In particular, the following sections of the application and report are requested to be kept confidential: Schematics Block Diagram Operational Description Parts List Rationale for request for confidentiality: Menix Co., Ltd., has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the confidential portions of this application to competitors would give them competitive advantage in developing similar products. If you have questions or need further information, please contact the undersigned. Sincerely Yours, Mr. GYU-CHEOL KIM / Manager Menix Co., Ltd. [email protected]

FCC ID. : QDYWT-200NF Page 1 of 4 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) FCC ID. : QDYWT-200NF Page 2 of 4 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) FCC ID. : QDYWT-200NF Page 3 of 4 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) FCC ID. : QDYWT-200NF Page 4 of 4 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904)

FCC ID. : QDYWT-200NF Page 1 of 1 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) IDENTIFICATION LABEL: PROPOSED FCC ID LABEL The FCC ID shall be permanently affixed to the rear side of the equipment FCC ID AREA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. Made in Korea FCC ID : QDYWT-200NF

FCC ID. : QDYWT-200NF Page 1 of 3 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) FCC ID. : QDYWT-200NF Page 2 of 3 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) FCC ID. : QDYWT-200NF Page 3 of 3 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904)

FCC ID. : QDYWT-200NF Page 1 of 19 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : E106R-013 AGR No : A103A-220 Applicant : Menix Co., Ltd. Address : 539, Yongsan-dong, Yuseong-gu, Daejeon, 305-500, Korea Manufacturer : Menix Co., Ltd. Address : 539, Yongsan-dong, Yuseong-gu, Daejeon, 305-500, Korea Type of Equipment : WIRELESS TRANSMITTER FCC ID. : QDYWT-200NF Model Name : WT-200NF Serial number : None Total page of Report : 19 pages (including this page) Date of Incoming : May 13, 2010 Date of issue : June 09, 2010 SUMMARY The equipment complies with the regulation; FCC Part 15 Subpart C Section 15.231. This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Prepared by: Reviewed by: Young-Min, Choi / Asst. Chief Engineer Y. K. Kwon / Managing Director EMC/RF Center EMC/RF Center ONETECH Corp. ONETECH Corp. FCC ID. : QDYWT-200NF Page 2 of 19 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ................................................................................................ 4 2. GENERAL INFORMATION ............................................................................................................... 5 2.1 PRODUCT DESCRIPTION.....................................................................................................................................................5 2.2 MODEL DIFFERENCES........................................................................................................................................................5 2.3 RELATED SUBMITTAL(S) / GRANT(S)................................................................................................................................5 2.4 PURPOSE OF THE TEST.......................................................................................................................................................5 2.5 TEST METHODOLOGY........................................................................................................................................................5 2.6 TEST FACILITY...................................................................................................................................................................5 3. SYSTEM TEST CONFIGURATION .................................................................................................. 6 3.1 JUSTIFICATION...................................................................................................................................................................6 3.2 PERIPHERAL EQUIPMENT...................................................................................................................................................6 3.3 MODE OF OPERATION DURING THE TEST...........................................................................................................................6 3.4. EUT MODIFICATIONS.................................................................................................................................................6 3.5 CONFIGURATION OF TEST SYSTEM...................................................................................................................................6 3.6 ANTENNA REQUIREMENT..................................................................................................................................................7 4. PRELIMINARY TEST ......................................................................................................................... 7 4.1 AC POWER LINE CONDUCTED EMISSIONS TESTS.............................................................................................................7 4.2 GENERAL RADIATED EMISSIONS TESTS............................................................................................................................7 5. FINAL RESULT OF MEASURMENT ............................................................................................... 8 5.1 CONDUCTED EMISSION TEST.............................................................................................................................................8 5.1.1 Operating Condition: Transmitting mode..................................................................................................................8 5.1.2 Operating Condition: Receiving mode.....................................................................................................................10 5.2 FIELD STRENGTH OF THE CARRIER TEST.......................................................................................................................12 5.3 TRANSMITTER TRANSMISSION DURATION......................................................................................................................13 5.4 SPURIOUS EMISSION TEST...............................................................................................................................................14 5.4.1 Operating Condition: Transmitting mode...................…

Text truncated - open the document above for the full version.

FCC ID. : QDYWT-200NF Page 1 of 2 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) Conducted Emission Test FCC ID. : QDYWT-200NF Page 2 of 2 Report No. : E106R-013 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003(Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-121 Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea.(TEL: 82-31-765-8289 FAX: 82-31-766-2904) Radiated Emission Test