QOAST-IIIBALARM CONTROL PANEL

P/N 20130320-1 ST-IIIB user manual Dear customer: Congratulations on purchasing you new security systeman thank you for the confidence you have shown in us.You have chosena high -quality. Productthathasbeenproduced,testedandpackedwthegreatest care.Pleasefamiliarizeyourselfwiththeseinstructionsbeforeatte mpting operationwillonlybeensureifitisfittedproperly.Wehope your new security system willbringyoulastingpleasure. Brief 产品手册 User manual Content 产品手册 User manual Chapter I Introduction 1 Chapter 2 Installation and Connection 4 2.1 Installation 4 2.2 Connection(N.O. N.C) 4 2.3 Install wired detector 4 2.4 Intall wereless detector 5 Chapter 3 Keybad and Operation 5 3.1 About panel 5 3.2 Basic operation 7 3.5 Alarm procedure 10 Chapter IV Voice alarm receiving 11 and GSM control 4.1 Remote phone control 11 4.2 Alarm receiving phone operation 11 4.3 GSM remote operation 12 4.4 GSM alarm receiving 12 4.5 GSM control via SMS 12 Chapter IV Voice alarm receiving and GSM control 13 5.1 Set system clock 13 5.2 Set user password 13 5.3 Set voice phone 13 Chapter VI System Setting 14 6.1 Set password 14 6.2 Set CMS number 15 3.3 Flashes when phone line cut 7 3.4 Host arm and disarm 8 6.3 Set voice phone 16 6.4 Set system options 17 6.4.1 Set system clock 17 产品手册 User manual 6.4.2 Set entry delay 18 6.4.3 Set exit delay 18 6.4.4 Set siren time 18 6.4.5 Set ring times 18 6.4.6 Set detector loss inspection 19 6.4.7 Set arm/disarm tone 19 6.4.8 Set arm/disarm report 20 6.4.9 Set others 2 0 6.4.9.1Set emergency alarm siren type 20 6.4.9.2 Ac off inspection time setting 21 6.4.9.3 Magnetic contact inspection 21 6.4.9.4 Check wireless detector tamper 21 6.4.9.5 Set force arm 2 1 6.4.9.7 Set zone alrm times 2 2 6.4.9.8 Set listen-in time 2 2 6.4.9.9 Set AC off remind 23 6.5 Manage wireless device 23 6.5.1 Set remote control 2 3 6.5.1.1 Enroll remote control 2 3 6.5.1.2 Enter remote control code 2 4 6.5.1.3 Delte remote control 2 4 6.5.2 Set detector 2 4 6.5.2.1 Detector coding 2 4 6.5.2.2 Enter detector code 2 5 6.5.2.3 Delete detector 25 6.5.3 Set appliance switch 2 5 6.5.3.1 Enroll appliance switch 2 5 6.5.3.2 Delete appliance switch 26 6.5.4 Enroll wireless siren 2 6 6.5.4.1 Enroll wireless siren 2 6 6.5.4.2 Delete wireless siren 2 6 6.6.5 Set door bell 2 7 6.5.5.1Enroll doorbell 27 6.5.5.2 Delete doorbell 27 6.4.9.6 Set telehpone line disconnect remind 22 产品手册 User manual 6.6.1 Set zone attribution 28 6.6.2 Set zone siren type 28 6.6.3 Set wired zone loop type 28 29 6.6.4 Set wired zone response speed 6.6.5 Set related zone 29 6.7 System maintance 30 6.7.1 Set timing operation 31 6.7.2 Recording 31 6.7.3 Play recording 31 6.7.4 Set programmable output port 31 6.7.6 Restore to factory default 32 6.7.5 Delete system events 32 6.8 Set GSM module 32 6.9 Advanced setting options 34 6.9.2 Set sever IP address 35 6.9.1 GPRS enable and disable 35 6.9.3 Set sever port 36 6.9.4 Set user ID 36 6.9.5 Set user password 36 6.9.6 GSM SMS language 36 6.9.7 Delay zone tone source options 37 6.9.8 Handshake tone input signal intensity 37 6.9.9 DTMF output signal intensity 37 6.9.10 Set LCD standby brightness 37 6.9.11 Alarm event retain time 38 Chapter VII technical specification 39 7.1 General data 39 7.2 Physical performance 39 Chapter VIII maintenance 40 8.1 Regular test 40 8.2 The cleanliness of control main machine 40 Chapter VX limitation of the products 40 IAlarm mode: with PSTN and GSM network alarm, GSM network with GPRS function(GPRS function is for China market only), remote arm and disarm panel through CMS or SMS CID protocol, SMS notification, the priority of PSTN and GSM network is Optional. With a new large-screen, full-touch buttons, LCD graphic display steps, work status,Alarm process easy and intuitive. The full English voice prompting operation: all local or remote operation, alarm information, event log view. 4 、 2、 3、 、GSM-hook and voice telephone with intercom function. 5、All alarm information can be programmed for the following settings: 0 does not send any information 1,Send only SMS 2,Only call users 3,SMS + call user 4, CMS only 5 ,CMS + SMS. 6,CMS + call user 7. CMS + SMS + call user 6、Sleep mode: Under sleep mode, all the lights, backlight, voice and remind tone are disabled. 7、Alarm panel under idle status is equivalent to a cellphone, you can call through the GSM network for balance inquiries 8、The associated zone: 4 groups associated zone, three kinds of association patterns, can effectively reduce false alarm or for other functions. 9、PGM output: With a programmed output port, followed by five kinds of alarm events output. 10、The doorbell Audio Optional: 1. Ding Dong 2 Welcome 3. Recording 4. Dee-Dee~ 11、Remote phone operation: dialing by telephone offsite, after password verification, you can arm, disarm, listen-in premise, system status query and electrical switches controls and other operations. 12、Voice Alarm: When panel alarm, it will automatically dial the preset user phone numbers to report alarm information then you can remote control the panel after enter user passwords. 1 产品手册 User manual Chapter I Introduction 1.1 Function Introduction 22、 23、For CMS Password access management: the panel has one administrator password 16 user password, The administrator password primarily for system administrators to set up the alarm system; The user passwords for users in the day-to-day use such arm/ disarm,remote operation. The administrator password, user password can be freely modified. networking alarm, depending on the number of users, the user can set four, six or eight user codes(account number). 2 14、8 wired zones, User can set the circuit type and speed of response, support N.O, N.C. 15、Enable enroll total 8 wireless remote,8 electronic switch,1 pc of wirele- ss doorbell and Unlimited for quantity of one way wireless siren. 16、 Follow me phone #,two for CMS,four for private alarm receiving. 17、Status inspection function:Enable record and inquiry 120 alarm event messages.Like the time wh…

Text truncated - open the document above for the full version.

Shenzhen Meian Technology Co.,Ltd . Address: No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Tel: 0755-84844181 Fax: 0755-84844464 2014-06-18 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: QOAST-IIIB We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics Diagram - Block Diagram - Operation description - Part placement - Part list The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Liuwei Cai / QA Head Contact information / address : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Tel: 0755-84844181 Fax: 0755-84844464

Shenzhen Meian Technology Co.,Ltd . FCC ID: QOAST-IIIB POWER OF ATTORNEY 2014-06-20 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen LCS Compliance Testing Laboratory Ltd. (MR. Gavin Liang, Manager) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen LCS Compliance Testing Laboratory Ltd. (MR. Gavin Liang, Manager) on our behalf shall have the same effect as acts of our own. This authorization expires on (2015-06-20). This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, (Shenzhen Meian Technology Co.,Ltd .), are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, ------------------------------- Client’s name / title : Liuwei Cai / QA Head Contact information / address : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Tel: 0755-84844181 Fax: 0755-84844464 Company Name: Shenzhen Meian Technology Co.,Ltd .

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 4 1. EXTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 Antenna SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 4 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 4 Fig.5 Fig.6 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 4 Fig.7 Fig.8 Antenna interface

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD FCC ID:QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size:L:5.0cm*W:3.0cm Label And Location

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 7 1. INTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 7 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 7 Fig.5 Fig.6 Antenna SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 7 Fig.7 Fig.8 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 5 of 7 Fig.9 Fig.10 Antenna SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 6 of 7 Fig.11 Fig.12 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.:LCS1405090396E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 7 of 7 Fig.13 Fig.14

Tune up procedure Tune up procedure shall be over the power range or at specific operating power levels. It must provide an operational voltage (DC 12V) to turn on the device and on one certain channel in service mode by means of company proprietary software. spectrum analyzer(Agilent, E440B) and base station simulator (Agilent 8960) measures the 2G device specific RF characteristics. The maximum gains of each individual device are adjusted until the target value met. Maximum RF Conducted Output Power(Peak) Frequency Bands Service PCL/Class Target Value(dBm) GSM 850 GSM 5 / Class 4 31.00 ± 1.0 GPRS (Slot 1) 5 / Class 4 30.00 ± 1.0 GPRS (Slot 2) 5 / Class 4 28.00 ± 1.0 GPRS (Slot 3) 5 / Class 4 27.00 ± 1.0 GPRS (Slot 4) 5 / Class 4 26.00 ± 1.0 PCS 1900 GSM 0 / Class 1 28.00 ± 1.0 GPRS (Slot 1) 0 / Class 1 27.00 ± 1.0 GPRS (Slot 2) 0 / Class 1 26.00 ± 1.0 GPRS (Slot 3) 0 / Class 1 25.00 ± 1.0 GPRS (Slot 4) 0 / Class 1 24.00 ± 1.0 Then these appropriate gain settings are stored in each device individually. The user has no possibility to change these settings later on, and during manufacturing each device will be individual calibrated. The measurement is done in fully calibrated setup, which is based on a Agilent 8960 base station simulator, spectrum analyzer(Agilent, E440B) and Power meter. Furthermore, the highest power level is verified afterwards in a call measurement on three channels (low, middle and high).

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 6 8. RADIO FREQUENCY EXPOSURE 8.1．Limit According to §1.1310 and §2.1091 RF exposure is calculated. Table: Limits for General Population/Uncontrolled Exposure F = frequency in MHz * = Plane-wave equivalent power density Maximum Permissible Exposure The MPE was calculated at 20cm to show compliance with the power density limit. S = PG/4πR 2 S = Power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna. Note: 1. Manufacturer declared that the maximum antenna gain is 3.0dBi for TX. 2. Manufacturer declared that the nearest distance between human and the EUT is 20cm. 3. Only record worst case data. SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 6 GSM 850 Conducted Peak output Power in dBm 31.24 dBm Max. Conducted Peak output Power in mW 1330.4544 mW Prediction distance 20 cm Prediction frequency 848.8 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.52964 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 GPRS 850(Slot 1) Conducted Peak output Power in dBm 30.35 dBm Max. Conducted Peak output Power in mW 1083.9269 mW Prediction distance 20 cm Prediction frequency 824.2 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.43200 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 6 GPRS 850(Slot 2) Conducted Peak output Power in dBm 28.44 dBm Max. Conducted Peak output Power in mW 698.2324 mW Prediction distance 20 cm Prediction frequency 836.6 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.27796 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 GPRS 850(Slot 3) Conducted Peak output Power in dBm 27.20 dBm Max. Conducted Peak output Power in mW 524.8075 mW Prediction distance 20 cm Prediction frequency 848.8 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.20892 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 6 GPRS 850(Slot 4) Conducted Peak output Power in dBm 26.58 dBm Max. Conducted Peak output Power in mW 454.9881 mW Prediction distance 20 cm Prediction frequency 824.2 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.18113 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 PCS 1900 Conducted Peak output Power in dBm 28.62 dBm Max. Conducted Peak output Power in mW 727.7798 mW Prediction distance 20 cm Prediction frequency 1850.2 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.28972 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 5 of 6 GPRS 1900(Slot 1) Conducted Peak output Power in dBm 27.39 dBm Max. Conducted Peak output Power in mW 548.2770 mW Prediction distance 20 cm Prediction frequency 1850.2 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.21826 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 GPRS 1900(Slot 2) Conducted Peak output Power in dBm 26.44 dBm Max. Conducted Peak output Power in mW 440.5549 mW Prediction distance 20 cm Prediction frequency 1850.2 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.17538 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 6 of 6 GPRS 1900(Slot 3) Conducted Peak output Power in dBm 25.39 dBm Max. Conducted Peak output Power in mW 345.9394 mW Prediction distance 20 cm Prediction frequency 1909.8 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.13771 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 GPRS 1900(Slot 4) Conducted Peak output Power in dBm 24.28 dBm Max. Conducted Peak output Power in mW 267.9168 mW Prediction distance 20 cm Prediction frequency 1850.2 MHz Antenna Gain(typical) 3.0 dBi Antenna Gain(numeric) 2.0 Power density at prediction frequency( S) 0.10665 mW/cm 2 MPE limit for uncontrolled exposure at prediction frequency 1 mW/cm 2 8.2 Test Results The power density level worst case at 20 cm is below the uncontrolled exposure limit.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 35 FCC TEST REPORT For Shenzhen Meian Technology Co.,Ltd . Alarm control panel Model No.: ST-IIIB Additional model No.: LA-S200 Prepared for : Shenzhen Meian Technology Co.,Ltd . Address : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Date of receipt of test sample : May 10, 2014 Number of tested samples : 1 Serial number : Prototype Date of Test : May 10, 2014– June 18, 2014 Date of Report : June 18, 2014 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 35 FCC TEST REPORT FCC CFR 47 PART 22 SUBPART H AND PART 24 SUBPART E Report Reference No. .............. : LCS1406100284E Date of Issue ................................ : June 18, 2014 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................ : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Testing Location/ Procedure ........ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : Shenzhen Meian Technology Co.,Ltd . Address ........................................ : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Test Specification Standard ....................................... : FCC CFR 47 PART 2, FCC CFR 47 PART 22 SUBPART H AND PART 24 SUBPART E Test Report Form No. ................ : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : Alarm control panel Trade Mark .................................. : Model/ Type reference ................. : ST-IIIB Ratings ......................................... : AC/DC Adapter:DC 15V, 2A By battery: DC 11.1V Result ......................................... : Positive Compiled by: Supervised by: Approved by: Jacky Li/ File administrators Danny Huang/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 35 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1406100284E June 18, 2014 Date of issue Type / Model........................... : ST-IIIB EUT......................................... : Alarm control panel Applicant............................... : Shenzhen Meian Technology Co.,Ltd . Address.................................. : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Shenzhen Meian Technology Co.,Ltd . Address................................... : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Telephone............................... : / Fax.......................................... : / Factory................................... : Shenzhen Meian Technology Co.,Ltd . Address................................... : No.32, Lanshui Rd, Longdong, Longgang District, Shenzhen, China Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QOAST-IIIB Report No.: LCS1406100284E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 35 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................... 5 1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS ............................................................................................. 6 1.3. EXTERNAL I/O CABLE .......................................................................................................................................... 6 1.4. DESCRIPTION OF TEST FACILITY ........................................................................................................................... 6 1.5. STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................ 6 1.6. MEASUREMENT UNCERTAINTY ............................................................................................................................ 7 1.7. TEST ENVIRONMENT .....................…

Text truncated - open the document above for the full version.