QQFPBTFABX2C2XBluetooth Headset

Confidential Page 1 8/26/2004 2210 O’Toole Ave. #200, San Jose, Ca. 95131 Tel: 408-576-1770 Fax: 408-576-1790 Windigo Products Friday, August 20, 2004 Ver.1.0 Windigo Bluetooth(TM) Headset User manual (Mini Headset Module) 2210 O'Toole Ave #200 San Jose, CA 95131 TEL : 408.576.1770 FAX : 408.576.1790 [email protected] http://www.windigosys.com/ Confidential Page 2 8/26/2004 2210 O’Toole Ave. #200, San Jose, Ca. 95131 Tel: 408-576-1770 Fax: 408-576-1790 FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Shielded interface cables must be used in order to comply with emission limits. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. Confidential Page 3 8/26/2004 2210 O’Toole Ave. #200, San Jose, Ca. 95131 Tel: 408-576-1770 Fax: 408-576-1790 1. Introduction Bluetooth profile K-6 gives an implementation guideline for Bluetooth headset application, which includes two functions: Bluetooth headset and Bluetooth audio gateway. Generally headset profile will be implemented in headset, and audio gateway will be implemented in cellular phone, PBX or other communication devices. Windigo systems has developed a fully Bluetooth V1.1 compliant headset module. This manual will explain the basic headset operation instruction to our customers. 2. A glimpse at the headset Figure 1 illustrates the reference headset and cellular phone. Figure 1. Windigo Bluetooth Headset Reference Design The headset module includes an amber LED, a blue LED, three buttons, and embedded audio connections and charging contact, these elements are illustrated in figure 2. Talk Button Amber LED Ear Hook Volume Up Volume Down Blue LED Figure 2. Key elements on Windigo Bluetooth Headset Confidential Page 4 8/26/2004 2210 O’Toole Ave. #200, San Jose, Ca. 95131 Tel: 408-576-1770 Fax: 408-576-1790 Both amber LED and blue LED are used to indicate various operation status for the headset, such as pairing, connecting, talking...etc. The three buttons are used to initialize various operations, such as activating the headset, turning off the headset, pairing, connecting, etc. Audio connections are used to connect an external microphone and speaker. Windigo Bluetooth Headset must be paired with an audio gateway before it is fully functional. Please refer to the audio gateway user manual on how to initialize and operate the audio gateway and its various functions. 3. Getting start Step 1: Be sure the headset battery is fully charged before the first time use. (Charging time is about 2 hours) Step 2: Enter into pairing (discoverable and connectable) mode During headset transportation, headset is on idle (deep sleep) mode to conserve battery power. While in this idle mode, both blue and amber LEDs are off. To enable the pairing mode, press and hold the talk button until blue and amber LED flash alternatively, and a PAIR tone will be heard. This press and hold time is about 5 seconds. Please be noted that before blue and amber LED flash alternatively, either blue or amber LED will flash shortly depends on the battery status, and an ON tone will be heard. So in order to enter into pairing mode correctly, please still hold the talk button. After the PAIR tone is heard, and blue and amber LED flash alternatively, then release the button. Note: 1. Default headset name is BTHS, and pin code is 0000 2. Pairing feature is used to establish the relationship between headset and audio gateway. Any given headset can only talk with the paired audio gateway after a successful pairing session. 3. Pairing mode can be cancelled by pressing and holding the talk button for about 3 seconds, until both amber LED and blue LED are off, and the OFF tone is heard. Then the headset is put into idle mode again. 4. Follow the instruction for specific audio gateway to perform the pairing. If the headset has been paired with audio gateway successfully, the headset will enter into standby (connectable only) mode. During this mode, blue LED will flash at 1-second interval if battery is full, and amber LED is off. Otherwise, if battery is low, then amber LED will flash at 1-second interval and blue LED will be off. Step 3: Confidential Page 5 8/26/2004 2210 O’Toole Ave. #200, San Jose, Ca. 95131 Tel: 408-576-1770 Fax: 408-576-1790 Now the headset is ready to use. The headset will ring whenever there is an incoming call. Step 4A: Answering the incoming call. When the headset is ringing, user can pick up the call by pressing the talk button once shortly. Note: Make sure the cellular phone has been configured correctly so an incoming call is transferred to the headset via Bluetooth link. Step 4B: Reject the incoming call. When the headse…

Text truncated - open the document above for the full version.

REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA APPENDIX 2 EXTERNAL OF EUT REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA All of EUT Front View of EUT (Model: PBTFABF2C2-X; ET2000 ; BTH3 ;BTH4) REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Back View of EUT (Model: PBTFABF2C2-X; ET2000 ; BTH3 ;BTH4) Top View of EUT (Model: PBTFABF2C2-X; ET2000 ; BTH3 ;BTH4) REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Front View of EUT (Model: PBHFABH2C2-X ; ET2000R ; BTH3R ;BTH4R) Back View of EUT (Model: PBHFABH2C2-X ; ET2000R ; BTH3R ;BTH4R)

FCC ID LABEL FORMAT AND LOCATION Applicant: Windigo SYSTEMS FCC ID: QQFPBTFABX2C2X FCC ID: QQFPBTFABX2C2X This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA APPENDIX 3 INTERNAL OF EUT REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Open View of EUT (Model: PBTFABF2C2-X; ET2000 ; BTH3 ;BTH4) Internal of EUT (Model: PBTFABF2C2-X; ET2000 ; BTH3 ;BTH4) REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Internal of EUT (Model: PBTFABF2C2-X; ET2000 ; BTH3 ;BTH4) Open View of EUT (Model: PBHFABH2C2-X ; ET2000R ; BTH3R ;BTH4R) REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Internal of EUT (Model: PBHFABH2C2-X ; ET2000R ; BTH3R ;BTH4R) Internal of EUT (Model: PBHFABH2C2-X ; ET2000R ; BTH3R ;BTH4R)

REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 Page: 1 of 53 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: Bluetooth Headset Brand Name: (1) Windigo (for model: PBTFABF2C2-X (X=A~Z), PBHFABH2C2-X (X=A~Z)); (2) ezTalker Mini (for model: ET2000, ET2000R); (3) V3 (for model: BTH3, BTH4, BTH3R, BTH4R) Model Name: PBTFABF2C2-X (X=A~Z), PBHFABH2C2-X (X=A~Z); ET2000, ET2000R; BTH3, BTH4, BTH3R, BTH4R Model Differences: These models are different in exterior looks and PCB layout. The variant model names depend on different trader in the market FCC ID: QQFPBTFABX2C2X Report No.: EF/2004/90002 Issue Date: Oct. 08, 2004 FCC Rule Part: 15.247 Prepared for Windigo SYSTEMS 2210 O’Toole Ave. #200, San Jose, CA 95131, U.S.A. Prepared by SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei County, Taiwan. Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 Page: 2 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA VERIFICATION OF COMPLIANCE Applicant: Windigo SYSTEMS 2210 O’Toole Ave. #200, San Jose, CA 95131, U.S.A. Equipment Under Test: Bluetooth Headset Brand Name: (1) Windigo (for model: PBTFABF2C2-X (X=A~Z), PBHFABH2C2-X (X=A~Z)); (2) ezTalker Mini (for model: ET2000, ET2000R); (3) V3 (for model: BTH3, BTH4, BTH3R, BTH4R) FCC ID Number: QQFPBTFABX2C2X Model No.: PBTFABF2C2-X (X=A~Z), PBHFABH2C2-X (X=A~Z); ET2000, ET2000R; BTH3, BTH4, BTH3R, BTH4R Model Difference: These models are different in exterior looks and PCB layout. The variant model names depend on different trader in the market File Number: EF/2004/90002 Date of test: Sep. 13, 2004 ~ Sep. 20, 2004 Date of EUT Received: Sep. 10, 2004 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. The test data, data evaluation, test proce- dures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2001) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247 The test results of this report relate only to the tested sample identified in this report. Test By: Date Oct. 08, 2004 Sky Wang Approved By Date Oct. 08, 2004 Vincent Su REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 Page: 3 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Table of Contents 1. GENERAL INFORMATION .........................................................................................................6 1.1. Product Description ............................................................................................................................6 1.2. Related Submittal(s) / Grant (s) ..........................................................................................................6 1.3. Test Methodology ...............................................................................................................................6 1.4. Test Facility.........................................................................................................................................6 1.5. Special Accessories .............................................................................................................................6 1.6. Equipment Modifications....................................................................................................................6 2. SYSTEM TEST CONFIGURATION ............................................................................................7 2.1. EUT Configuration .............................................................................................................................7 2.2. EUT Exercise ......................................................................................................................................7 2.3. Test Procedure.....................................................................................................................................7 2.4. Configuration of Tested System..........................................................................................................8 3. SUMMARY OF TEST RESULTS .................................................................................................9 4. DESCRIPTION OF TEST MODES ..............................................................................................9 5. CONDUCTED EMISSION TEST................................................................................................10 5.1. Standard Applicable ..........................................................................................................................10 5.2. EUT Setup......................................…

Text truncated - open the document above for the full version.

REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA APPENDIX 1 PHOTOGRPHS OF SET UP REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Radiated Emission Set up Photos REPORT NO: EF/2004/90002 ID: QQFPBTFABX2C2X DATE: Oct. 08, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Conducted Emission Setup Photos