QTLBH-110Bluetooth headset

Nokia Bluetooth Headset BH-110 User Guide Issue 1 Introduction About your headset With the Nokia Bluetooth BH-110 headset, you can handle calls hands-free, even when you are using two phones at the same time. The surface of this product is nickel-free. Warning: This product may contain small parts. Keep them out of the reach of small children. Parts of the product are magnetic. Metallic materials may be attracted to the product. Do not place credit cards or other magnetic storage media near the product, because information stored on them may be erased. Read this user guide carefully before using the product. Also, read the user guide for the device that you connect to the product. About Bluetooth connectivity You can use Bluetooth to make a wireless connection to other compatible devices, such as mobile phones. Devices do not need to be in direct line-of-sight, but they must be within 10 metres (33 feet) of each other. The connection may be affected by obstructions such as walls or other electronic devices. This device is compliant with Bluetooth Specification 2.1 +EDR supporting the following profiles: Headset Profile (HSP) 1.1, Handsfree Profile (HFP) 1.5. Check with the manufacturers of other devices to determine their compatibility with this device. 2 Get started Keys and parts 1Charger connector 2Indicator light 3Microphone 4Multifunction key 5Earpiece 6Earloop Charge the battery Before using the headset, you must charge the battery. Warning: Use only chargers approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous. Use of unapproved chargers may present a risk of fire, explosion, or other hazard. 1Connect the charger to a wall outlet. 2Connect the charger cable to the charger connector on the headset. The red indicator light turns green when the battery is fully charged. 3Disconnect the charger from the headset, then from the wall outlet. When you unplug a charger, hold and pull the plug, not the cord. The fully charged battery has power for up to 6 hours of talk time or up to 120 hours of standby time. 3 When the battery charge is low, the headset beeps every 5 minutes, and the red indicator light flashes. When the battery is charging, the red indicator light is on. Check the battery charge Make sure the headset is switched on, and press . A green light indicates a sufficient charge level. If the light is yellow, you may need to recharge the battery soon. If the light is red, recharge the battery. Switch the headset on or off Switch on Press and hold for 2 seconds. The headset beeps, and a green indicator light flashes once. The headset connects to the last connected device. If you have never paired the headset with a device, or you have cleared the pairings, pairing mode is activated. Switch off Press and hold for 5 seconds. The headset beeps, and a red indicator light flashes once. All active calls are ended. If not connected to a device within 30 minutes, the headset switches off. Pair and connect the headset to your phone Before using the headset, you must pair and connect it to a compatible phone. 1To switch the headset off, press and hold for 5 seconds. 2Switch on the phone to pair with. 3If you have never paired the headset with a device, or you have cleared the pairings, switch the headset on. If you have previously paired your headset with a device, press and hold for 5 seconds. Pairing mode is activated, and a green indicator light starts to flash quickly. 4Within 3 minutes, activate Bluetooth on the phone, and set it to search for Bluetooth devices. For details, see the user guide of the phone. 5Select the headset from the list of found devices. 6If required, enter the passcode 0000. You can pair your headset with 8 compatible phones, but you can only connect it to a maximum of 2 phones at the same time. With some phones, you may need to make the connection separately after pairing. 4 Wear the headset If you want to use the headset with the earloop, attach the earloop to the headset. To detach the earloop, gently pull it from the headset. Slide the earloop behind your ear, and gently push the earpiece against your ear. Carefully bend the earloop around your ear for the best fit. Point the headset towards your mouth. Make calls Make and receive calls To make and receive calls using your headset, you need to connect it to your phone. Make a call Make a call in the normal way. Answer a call Press . End a call Press . 5 Reject a call Press twice. Switch a call between your headset and phone Press and hold for 2 seconds. You can redial the last called number or use voice dialling, if your phone supports these features with the headset. Redial the last called number When no call is in progress, press twice. Use voice dialling When no call is in progress, press and hold for 2 seconds, and follow the instructions in the user guide of your phone. Change the volume Set the desired volume level on your connected phone. The selected volume level is saved as the minimum volume level for the phone that is currently connected to the headset. Pair and connect the headset to two phones When you use the headset for the first time, it automatically connects to your phone. You can also connect your headset to another phone, and manage calls from, for example, both your personal and your work phone at the same time. 1To switch the headset off, press and hold for 5 seconds. 2To activate pairing mode, press and hold for 5 seconds, and pair the headset with the second phone. 3Make sure Bluetooth is activated on both phones, and switch the headset off and back on. The headset connects to both phones. Handle calls from two phones If your headset is connected to two phones, you can handle calls from both at the same time. End an ongoing call, and answer a call on another phone Press . Put an ongoing call on hold, and answer a call on another phone Press and hold for 2 seconds. Switch between active and held cal…

Text truncated - open the document above for the full version.

Nokia (China) Investment Co., Ltd B2, Nokia China Campus Beijing Economic and Tech Development Area, No.5 Donghuan Zhonglu Beijing, 100176 China PRC Tel. +861087118888 Fax +861087114550 Nov 25 , 2010 Federal Communications Commission Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch This letter will authorize the appointment of Liu Chunbin act as our agent in all FCC matters for grantee code QTL. This appointment is effective until otherwise notified by us. Sincerely, Nokia (China) Investment Co., Ltd Wang Yan Product Certification Officer Beijing, PRC.

External Photos:

Certification Application Confidential Nokia Bluetooth Mono Headset BH-110 Type Label Change History . Item Version HW V4.0 SW B4.0.0.1 MV V2.0 Version Date Status Comments 1.0 Sep.14,2011 Draft Create an initial draft document 56 . 0 mm 1 7 . 4mm 29 . 3mm 6 . 7mm 1 0 . 6mm 6 . 7mm 8 . 7mm 1 0 . 6mm 6 . 7mm 6 . 8mm 8 . 7mm E U & N A M L T A B r a z l C h i na

Internal Photos:

INTERTEK TESTING SERVICES Radio Frequency Radiation Exposure, FCC Rule 15.247(i): The EUT is a Bluetooth headset. According to the DA 00-705 and KDB 447498, The power thresholds for source-based time-averaging conducted output power (in the worst-case duty cycle of DH5 of 8DPSK modulation type) = 5.35*(T on/ (Ton+Toff)) mW <5.35mW, since (T on/ (Ton+Toff)) < 1 The power thresholds for source-based time-averaging radiated output power (The worst-case radiated emission is 101.7 dBμV/m at 3m in 8DPSK modulation type) = [(FS*D) ^2 / 30]*(Ton/ (Ton+Toff)) mW = 4.44*(T on/ (Ton+Toff)) mW < 4.44mW, since (Ton/ (Ton+Toff)) < 1 And SAR Low Threshold Level: 60/f (GHz) = 60/2.45 = 24.5 mW = 13.9 dBm Since the source-based time-averaging conducted output power and radiated output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: QTLBH-110

Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com 14 September, 2011 Nokia (China) Investment Co., Ltd B2, Nokia China Campus. Beijing Economic and Tech Development Area, No.5. Donghuan Zhonglu. Beijing China Dear Yan Wang, Enclosed you will find your file copy of a Part 15 report (FCC ID: QTLBH-110). For your reference, TCB will normally take another one week for reviewing the report. Approval will then be granted when no query is sorted. Please contact me if you have any questions regarding the enclosed material. Sincerely, Shawn Xing Manager Enclosure • The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF No.: FCC 15C_TXa FCC ID: QTLBH-110 Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Nokia (China) Investment Co., Ltd Application For Certification (FCC ID: QTLBH-110) Bluetooth headset Model: BH-110 (HW: V4.0; SW: B4.0.0.1; MV: V2.0) 2.4GHz Transceiver SZ11090192-1 Billy Li 14 September, 2011 INTERTEK TESTING SERVICES TRF No.: FCC 15C_Txa FCC ID: QTLBH-110 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information EXHIBIT 9: Test Equipment List INTERTEK TESTING SERVICES TRF No.: FCC 15C_Txa FCC ID: QTLBH-110 ii MEASUREMENT/TECHNICAL REPORT Nokia (China) Investment Co., Ltd MODEL: BH-110 (HW: V4.0; SW: B4.0.0.1; MV: V2.0) FCC ID: QTLBH-110 14 September, 2011 This report concerns (check one:) Original Grant X Class II Change Equipment Type: DSS - Part 15 Spread Spectrum Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-10 Edition] provision. Report prepared by: Shawn Xing Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8601 6288 Fax: (86 755) 8601 6751 INTERTEK TESTING SERVICES TRF No.: FCC 15C_Txa FCC ID: QTLBH-110 iii Table of Contents 1.0 General Description............................................................................................ 2 1.1 Product Description ............................................................................................ 2 1.2 Test Methodology............................................................................................... 2 1.3 Test Facility........................................................................................................ 2 2.0 System Test Configuration ................................................................................. 4 2.1 Justification ........................................................................................................ 4 2.2 EUT Exercising Software.................................................................................... 4 2.3 Special Accessories ........................................................................................... 4 2.4 Equipment Modification ...................................................................................... 4 2.5 Measurement Uncertainty .................................................................................. 5 2.6 Support Equipment List and Description ............................................................. 5 3.0 Test Results ......................................................................................................... 7 3.1 Radiated Test Result .......................................................................................... 8 3.1.1 Field Strength Calculation................................................................................ 8 3.1.2 Radiated Emission Configuration Photograph .................................................. 9 3.1.3 Radiated Emissions......................................................................................... 9 3.1.4 Transimitter Spurious Emissions (Radiated) .................................................. 11 3.1.5 Receiver Spurious Emissions (Radiated) ....................................................... 15 3.2 Conducted Emissions at Main…

Text truncated - open the document above for the full version.

Conducted Photos

Radiated Photos