QTLRM-733GSM 850/1900 Cellular Telephone

Nokia X1-00 User Guide 5555555 Issue 1 CyanCyanMagentaMagentaYellowYellowBlackBlack Contents Safety3 Get started5 Insert the SIM card and battery5 Insert or remove a memory card7 Charge the battery9 Switch on or off10 Your phone11 Keys and parts11 Make and answer a call13 Text input14 Message15 Contacts16 Multi-phonebook17 Listen to music18 FM Radio19 Flashlight21 Support21 Protect the environment22 Save energy22 Recycle23 Product and safety information23 Index33 2www.nokia.com/support CyanCyanMagentaMagentaYellowYellowBlackBlack Safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information. SWITCH OFF IN RESTRICTED AREAS Switch the device off when mobile phone use is not allowed or when it may cause interference or danger, for example, in aircraft, near medical equipment, fuel, chemicals, or blasting areas. ROAD SAFETY COMES FIRST Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety. INTERFERENCE All wireless devices may be susceptible to interference, which could affect performance. QUALIFIED SERVICE Only qualified personnel may install or repair this product. 3 CyanCyanMagentaMagentaYellowYellowBlackBlack BATTERIES AND OTHER ACCESSORIES Use only batteries, chargers and other accessories approved by Nokia for use with this device. Do not connect incompatible products. KEEP YOUR DEVICE DRY Your device is not water-resistant. Keep it dry. PROTECT YOUR HEARING Listen to a headset at a moderate level, and do not hold the device near your ear when the loudspeaker is in use. 4 CyanCyanMagentaMagentaYellowYellowBlackBlack Get started Insert the SIM card and battery Important: Do not use a mini-UICC SIM card, also known as a micro-SIM card, a micro-SIM card with an adapter, or a SIM card that has a mini-UICC cutout (see figure) in this device. A micro SIM card is smaller than the standard SIM card. This device does not support the use of micro-SIM cards and use of incompatible SIM cards may damage the card or the device, and may corrupt data stored on the card. The SIM card and its contacts can be easily damaged by scratches or bending, so be careful when handling, inserting, or removing the card. 1Place your finger in the recess at the bottom of the device, and carefully lift and remove the back cover (1). 2If the battery is inserted, lift the battery out (2). 5 CyanCyanMagentaMagentaYellowYellowBlackBlack 3Open the SIM card holder (3). Make sure the contact area is facing down, and insert the SIM card (4). Close the holder. 4Line up the contacts of the battery and the battery compartment, and insert the battery (5). To replace the back cover, direct the top locking catches toward their slots (6), and press down until the cover locks into place (7). 6 CyanCyanMagentaMagentaYellowYellowBlackBlack This phone is intended for use with the BL-5J battery. Insert or remove a memory card Use only compatible memory cards approved by Nokia for use with this device. Incompatible cards may damage the card and the device and corrupt data stored on the card. Your device supports microSD cards with a capacity of up to 16 GB. 7 CyanCyanMagentaMagentaYellowYellowBlackBlack Insert a memory card 1Open the cover of the memory card slot. 2Insert the memory card. Push the card in, until it locks into place. Make sure the contact area is facing up. 3Close the slot cover. You can remove or replace the memory card without switching the device off. Remove the memory card Important: Do not remove the memory card when an application is using it. Doing so may damage the memory card and the device, and corrupt data stored on the card. 1Open the cover of the memory card slot. 8 CyanCyanMagentaMagentaYellowYellowBlackBlack 2Push the card in gently, until it is released, and pull the card out. 3Close the slot cover. Charge the battery Your battery has been partially charged at the factory, but you may need to recharge it before you can switch on your device for the first time. If the device indicates a low charge, do the following: 1Connect the charger to a wall outlet. 2Connect the charger to the device. 3When the device indicates a full charge, disconnect the charger from the device, then from the wall outlet. Tip: To save energy, unplug the charger when the battery is fully charged. 9 CyanCyanMagentaMagentaYellowYellowBlackBlack You do not need to charge the battery for a specific length of time, and you can use the device while it is charging. If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or before any calls can be made. If the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and reconnect it. It may take longer than expected before the device is fully charged, due to the large capacity of the BL-5J battery. Switch on or off Press and hold the end key. Use the phone only in its normal operating position. Avoid touching the antenna area unnecessarily while the antenna is transmitting or receiving. Contact with 10 CyanCyanMagentaMagentaYellowYellowBlackBlack antennas affects the communication quality and may cause a higher power level during operation and may reduce the battery life. Your phone Keys and parts 1End/Power key 2Earpiece 3Display 4Selection keys 5Navi™ key (scroll key) 6Call key 11 CyanCyanMagentaMagentaYellowYellowBlackBlack 7Keypad 8Microphone 9Wrist strap hole 10Music keys 12 CyanCyanMagentaMagentaYellowYellowBlackBlack 11Charger connector 12Flashlight 13Headset connector/Nokia AV Connector (3.5 mm) 14Memory card slot 15Loudspeaker Make and answer a call Make a call Enter the phone number, including the country code and area code, if necessary, and press the call key. Answer a call Press the call key. End or reject a call Press the end key. Use the loudspeaker or earpiece During a call, select Loudsp…

Text truncated - open the document above for the full version.

Nokia (China) Investment Co., Ltd B2, Nokia China Campus Beijing Economic and Tech Development Area, No.5 Donghuan Zhonglu Beijing, 100176 China PRC Tel. +861087118888 Fax +861087114550 Jan 18, 2011 Federal Communications Commission Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch REQUEST FOR CONFIDENTIALITY Pursuant to Sections 0.457 (d) (l) (ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of some of the information accompanying this Application of FCC ID: QTLRM-733 and as outlined below: - Exhibit 4: Block Diagram - Exhibit 5: Schematic Diagrams - Exhibit 10: List of Active Devices and Tune-Up Procedure - Exhibit 12: Theory of Operation / Description of Circuitry These materials contain trade secrets and proprietary information not customarily released to the public and the public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457 (d) (l) (ii) disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. NOKIA CORPORATION Wang Yan Product Certification Officer Beijing, PRC.

Nokia (China) Investment Co., Ltd B2, Nokia China Campus Beijing Economic and Tech Development Area, No.5 Donghuan Zhonglu Beijing, 100176 China PRC Tel. +861087118888 Fax +861087114550 Jan 25, 2011 Federal Communications Commission Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch REQUEST FOR SHORT TERM CONFIDENTIALITY Pursuant to Section 0.459 of the Commission’s Rules and Public Notice DA 04-1705 of June 15, 2004, the Applicant hereby requests for 180 days short term confidential treatment of some of the information accompanying this application of FCC ID: QTLRM-733 and as outlined below: - Exhibit 3: External photos - Exhibit 7: Test setup photos - Exhibit 8: User's manual - Exhibit 9: Internal photos These materials contain proprietary information not yet released to the public and the public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. NOKIA CORPORATION Wang Yan Product Certification Officer Beijing, PRC.

1 (6) RM-733 External Picture FCC ID: QTLRM-733 IC: 661AB-RM733 2 (6) RM-733 External Picture FCC ID: QTLRM-733 IC: 661AB-RM733 3 (6) RM-733 External Picture FCC ID: QTLRM-733 IC: 661AB-RM733 4 (6) RM-733 External Picture FCC ID: QTLRM-733 IC: 661AB-RM733 5 (6) RM-733 External Picture FCC ID: QTLRM-733 IC: 661AB-RM733 6 (6) RM-733 External Picture FCC ID: QTLRM-733 IC: 661AB-RM733

1 (3) RM-733 Internal Picture FCC ID: QTLRM-733 IC: 661AB-RM733 2 (3) RM-733 Internal Picture FCC ID: QTLRM-733 IC: 661AB-RM733 3 (3) RM-733 Internal Picture FCC ID: QTLRM-733 IC: 661AB-RM733

Nokia ____________________________________________________________________________ SAR Report FCC_RM-733_01 Applicant: Nokia Corporation Type: RM-733 Copyright  2011 TCC Nokia 1/37 SAR Compliance Test Report Test report no.: FCC_RM-733_01 Date of report: 2010-12-30 Template version: 16.1 Number of pages: 37 Testing laboratory: TCC Nokia Beijing Laboratory Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 Client: Nokia Corporation Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 Responsible test engineer: Liang Dong Product contact person: Xu Helen Measurements made by: Liang Dong Tested device: RM-733 FCC ID: QTLRM-733 IC: 661AB-RM733 Supplement reports: SAR_Photo_RM-733_02 Testing has been carried out in accordance with: 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices FCC OET Bulletin 65 (Edition 97-01), Supplement C (Edition 01-01) Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields RSS-102 Evaluation Procedure for Mobile and Portable Radio Transmitters with Respect to Health Canada’s Safety Code 6 for Exposure of Humans to Radio Frequency Fields IEEE 1528 - 2003 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Technique Documentation: The documentation of the testing performed on the tested devices is archived for 15 years at TCC Nokia. Test results: The tested device complies with the requirements in respect of all parameters subject to the test. The test results and statements relate only to the items tested. The test report shall not be reproduced except in full, without written approval of the laboratory. Date and signatures: For the contents: Nokia ____________________________________________________________________________ SAR Report FCC_RM-733_01 Applicant: Nokia Corporation Type: RM-733 Copyright  2011 TCC Nokia 2/37 CONTENTS 1. SUMMARY OF SAR TEST REPORT ............................................................................................................................................. 3 1.1 TEST DETAILS ............................................................................................................................................................................. 3 1.2 MAXIMUM RESULTS .................................................................................................................................................................... 3 1.2.1 Head Configuration ........................................................................................................................................................ 3 1.2.2 Body Worn Configuration ............................................................................................................................................ 3 1.2.3 Maximum Drift ................................................................................................................................................................ 3 1.2.4 Measurement Uncertainty ........................................................................................................................................... 4 2. DESCRIPTION OF THE DEVICE UNDER TEST ........................................................................................................................... 4 2.1 ESCRIPTION OF THE ANTENNA ..................................................................................................................................................... 4 3. TEST CONDITIONS ..................................................................................................................................................................... 4 3.1 TEMPERATURE AND HUMIDITY .................................................................................................................................................... 4 3.2 TEST SIGNAL, FREQUENCIES AND OUTPUT POWER ...................................................................................................................... 4 3.3 TEST CASES AND TEST MINIMISATION ........................................................................................................................................ 5 4. DESCRIPTION OF THE TEST EQUIPMENT ............................................................................................................................... 7 4.1 MEASUREMENT SYSTEM AND COMPONENTS ................................................................................................................................ 7 4.1.1 Isotropic E-field Probe Type ET3DV6 ......................................................................................................................... 8 4.2 PHANTOMS ................................................................................................................................................................................ 8 4.3 TISSUE SIMULANTS .................................................................................................................................................................... 8 4.3.1 Tissue Simulant Recipes ............................................................................................................................................... 9 4.3.2 System Checking ............................................................................................................................................................. 9 4.3.3 Tissue Simulants used in the Measurements ....................................................................................................... 10 5. DESCRIPTION OF THE TEST PROCEDURE ................................................................................................…

Text truncated - open the document above for the full version.

FCC Part 22, 24 Compliance Test Report / Template Version 15.0 FCC22, 24_RM-733_02.docx Copyright © TCC Nokia 1 (13) TCC Nokia Tampere Laboratory P.O. Box 68 Sinitaival 5 FIN-33720 TAMPERE, FINLAND Tel. +358 (0) 7180 46800 Fax. +358 (0) 7180 46880 FCC Part 22/24 Compliance Test Report Test Report no.: FCC22, 24_RM-733_02.docx Date of Report: 24-Jan-2011 Number of pages: 13 Customer’s Contact person: Helen Hu Testing laboratory: TCC Nokia Tampere Laboratory P.O. Box 68 Sinitaival 5 FIN-33720 TAMPERE, FINLAND Tel. +358 (0) 7180 46800 Fax. +358 (0) 7180 46880 Customer: Nokia Corporation Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 FCC listing no.: IC recognition no.: 94436 661AK-1 Tested devices/ accessories: Phone RM-733 / Battery BL-5J, AC charger AC-8E, Headset WH-102 FCC ID: QTLRM-733 IC: 661AB-RM733 Supplement reports: - Testing has been carried out in accordance with: CFR 47, FCC rules Parts 22/24 , TIA-603-C-2004 and IC standards, RSS-GEN (Issue 3, December 2010), RSS-132 (Issue 2, September 2005), RSS-133 (Issue 5, February 2009). Deviations, modifications or clarifications (if any) to above mentioned documents are written in each section under "Test method and limit". Documentation: The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory. The documentation of the testing performed on the tested devices is archived for 15 years at TCC Nokia. Test Results: The EUT complies with the requirements in respect of all parameters subject to the test. The test results relate only to devices specified in this document Date and signature for the contents: Jari Jantunen, System Manager, EMC FCC Part 22, 24 Compliance Test Report / Template Version 15.0 FCC22, 24_RM-733_02.docx Copyright © TCC Nokia 2 (13) TCC Nokia Tampere Laboratory P.O. Box 68 Sinitaival 5 FIN-33720 TAMPERE, FINLAND Tel. +358 (0) 7180 46800 Fax. +358 (0) 7180 46880 1. Summary for FCC Part 22/24 Compliance Test Report Date of receipt 04-Jan-2011 Testing completed 07-Jan-2011 The customer's contact person Helen Hu Test Plan referred to T:\Projects\RM-733\TestPlan\RS_Testplan_RM-733.xls Notes - Document name T:T:\Projects\RM-733\EMC\FCC22, 24_RM-733_02.docx 1.1. EUT and Accessory Information The EUT is a 3-band (GSM850/1900) and WCDMA Band (1900) mobile phone. The EUT is tested with maximum rated TX power, modulated with pseudo random bit sequence (PRBS9). Product Type SN HW MV SW DUT Phone RM-733 001004004145414 0202 - 42437 Battery BL-5J 4620400302M20257209;0670573 - - - 42438 Charger AC-8E 4868670162530606694;0675387 - - - 42390 Headset WH-102 0694323019582R00111 - - - 42397 1.2. Summary of Test Results GSM850: Section in CFR 47 Section in RSS-GEN or RSS-132 Name of the test Result §2.1046(a), 22.913(a) 4.4 Conducted RF output power NP §22.913(a) 4.4 Radiated RF output power PASSED §2.1049(h) 4.6.1 99 % occupied bandwidth NP §22.917(a) 4.5 Band edge compliance PASSED §22.917(a), §2.1051 4.5 Spurious emissions at antenna terminals NP §22.917(a), §2.1053 4.5 Spurious radiated emissions PASSED §2.1055(a) 4.3 Frequency stability, temperature variation NP §2.1055(d) 4.3 Frequency stability, voltage variation NP FCC Part 22, 24 Compliance Test Report / Template Version 15.0 FCC22, 24_RM-733_02.docx Copyright © TCC Nokia 3 (13) TCC Nokia Tampere Laboratory P.O. Box 68 Sinitaival 5 FIN-33720 TAMPERE, FINLAND Tel. +358 (0) 7180 46800 Fax. +358 (0) 7180 46880 GSM1900: Section in CFR 47 Section in RSS-GEN or RSS-133 Name of the test Result §2.1046(a) 6.4 Conducted RF output power NP §24.232(b) 6.4 Radiated RF output power PASSED §2.1049(h) 4.6.1 99 % occupied bandwidth NP §24.238(a) 6.5 Band edge compliance PASSED §24.238(a), §2.1051 6.5 Spurious emissions at antenna terminals NP §24.238(a), §2.1053 6.5 Spurious radiated emissions PASSED §2.1055(a) 6.3 Frequency stability, temperature variation NP §2.1055(d) 6.3 Frequency stability, voltage variation NP PASSED The EUT complies with the essential requirements in the standard. FAILED The EUT does not comply with the essential requirements in the standard. NP The test was not performed by the TCC Nokia Laboratory. FCC Part 22, 24 Compliance Test Report / Template Version 15.0 FCC22, 24_RM-733_02.docx Copyright © TCC Nokia 4 (13) TCC Nokia Tampere Laboratory P.O. Box 68 Sinitaival 5 FIN-33720 TAMPERE, FINLAND Tel. +358 (0) 7180 46800 Fax. +358 (0) 7180 46880 CONTENTS1. Summary for FCC Part 22/24 Compliance Test Report 2 1.1. EUT and Accessory Information ........................................................................................... 2 1.2. Summary of Test Results ..................................................................................................... 2 2. Radiated RF output power (FCC §22.913(a), §24.232(b), RSS-132 4.4, RSS-133 6.4) ............................................... 5 2.1. Test method and limit ........................................................................................................... 5 2.2. GSM 850 Test results ........................................................................................................... 6 2.3. GSM1900 TX Test results .................................................................................................... 6 3. Band edge compliance (FCC §22.917(a), §24.238(a), RSS-132 4.5, RSS-133 6.5)................................................ 7 3.2. Test method and limit ........................................................................................................... 7 3.3. GSM850 Test results ............................................................................................................ 8 3.4. GSM1900 Test results .......................................................................................................... 9 4. Spurious radiated emissions (FCC §22.917(a), §2.1053, §24.238(a), §2.1053, RSS-…

Text truncated - open the document above for the full version.

FCC Part 22/24/27 Compliance Test Report / Template Version 15.0 FCC22&24_RM-733_03.doc Copyright © TCC Nokia 1 (10) TCC Nokia Beijing Laboratory Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 FCC Part 22/24 Compliance Test Report Test Report no.: FCC22&24_RM-733_03.docx Date of Report: 10-Jan-2011 Number of pages: 10 Customer’s Contact person: Xu Helen Testing laboratory: TCC Nokia Beijing Laboratory Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 Customer: Nokia Corporation Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 FCC listing no.: IC recognition no.: 975940 661AH-1 Tested devices/ accessories: Phone RM-733 / Battery BL-5J / AC-charger AC-10UC / Charging data cable CA-100 / Headset WH-102 / Dummy Battery SD-50B FCC ID: QTLRM-733 IC: 661AB-RM733 Supplement reports: - Testing has been carried out in accordance with: CFR 47, FCC rules Parts 22 and 24, TIA-603-C-2004 and IC standards RSS-GEN (Issue 3, December 2010), RSS-132 (Issue 2, September 2005) and RSS-133 (Issue 5, February 2009). Deviations, modifications or clarifications (if any) to above mentioned documents are written in each section under "Test method and limit". Documentation: The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory. The documentation of the testing performed on the tested devices is archived for 15 years at TCC Nokia. Test Results: The EUT complies with the requirements in respect of all parameters subject to the test. The test results relate only to devices specified in this document. Date and signature for the contents: Jia Dongsheng, System Manager FCC Part 22/24/27 Compliance Test Report / Template Version 15.0 FCC22&24_RM-733_03.doc Copyright © TCC Nokia 2 (10) TCC Nokia Beijing Laboratory Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 1. Summary for FCC Part 22/24 Compliance Test Report Date of receipt 27-Dec-2010 Testing completed 05-Jan-2011 The customer's contact person Xu Helen Test Plan referred to T:\Projects\RM-733\TestPlan\RS_Testplan_RM-733.xls Notes - Document name FCC22&24_RM-733_03.docx 1.1. EUT and Accessory Information The EUT is a 2-band (GSM850/1900) mobile phone. The EUT is tested with maximum rated TX power, modulated with pseudo random bit sequence (PRBS9). Product Type SN HW MV SW DUT Phone RM-733 001004004145703 0202 - 03.25 51970 Battery BL-5J 4620400302M20257211;0670573 - - - 51974 AC-charger AC-10UC 3997910435020103064;0675474 - - - 51975 Charging data cable CA-100 0730639735311800148 - - - 51976 Headset WH-102 06943239375c4106666 - - - 51704 Dummy Battery SD-50B 07484K - - - 52056 1.2. Summary of Test Results GSM 850: Section in CFR 47 Section in RSS-GEN or RSS-132 Name of the test Result §2.1046(a), 22.913(a) 4.4 Conducted RF output power NP §22.913(a) 4.4 Radiated RF output power NP §2.1049(h) 4.6.1 99 % occupied bandwidth PASSED §22.917(a) 4.5 Band edge compliance NP §22.917(a), §2.1051 4.5 Spurious emissions at antenna terminals NP §22.917(a), §2.1053 4.5 Spurious radiated emissions NP §2.1055(a) 4.3 Frequency stability, temperature variation PASSED §2.1055(d) 4.3 Frequency stability, voltage variation PASSED GSM 1900: Section in CFR 47 Section in RSS-GEN or RSS-133 Name of the test Result §2.1046(a) 6.4 Conducted RF output power NP §24.232(b) 6.4 Radiated RF output power NP §2.1049(h) 4.6.1 99 % occupied bandwidth PASSED §24.238(a) 6.5 Band edge compliance NP §24.238(a), §2.1051 6.5 Spurious emissions at antenna terminals NP §24.238(a), §2.1053 6.5 Spurious radiated emissions NP §2.1055(a) 6.3 Frequency stability, temperature variation PASSED §2.1055(d) 6.3 Frequency stability, voltage variation PASSED PASSED The EUT complies with the essential requirements in the standard. FAILED The EUT does not comply with the essential requirements in the standard. NP The test was not performed by the TCC Nokia Beijing Laboratory. FCC Part 22/24/27 Compliance Test Report / Template Version 15.0 FCC22&24_RM-733_03.doc Copyright © TCC Nokia 3 (10) TCC Nokia Beijing Laboratory Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 CONTENTS 1. Summary for FCC Part 22/24 Compliance Test Report ............................................ 2 1.1. EUT and Accessory Information ........................................................................................... 2 1.2. Summary of Test Results ..................................................................................................... 2 2. 99 % occupied bandwidth (FCC §2.1049(h), RSS-GEN 4.6.1) ..................................................................................... 4 2.1. Test setup ............................................................................................................................ 4 2.2. Test method and limit ........................................................................................................... 4 2.3. GSM 850 Test results........................................................................................................... 5 2.4. GSM 1900 Test results ......................................................................................................... 5 3. Frequency stability, temperature variation (FCC §2.1055(a), RSS-132 4.3, RSS-133 6.3).................................................................... 6 3.1. Test setup ............................................................................................................................ 6 3.2. Test method and limit ........................................…

Text truncated - open the document above for the full version.

Nokia ____________________________________________________________________________ SAR Report SAR_Photo_RM-733_02 Applicant: Nokia Corporation Type: RM-733 Copyright  2010 TCC Nokia 1/4 Test Setup photos for RM-733 SAR Compliance Test Report Test report no.: SAR_Photo_RM-733_02 Date of report: 2010-12-30 Template version: 16.1 Number of pages: 4 Testing laboratory: TCC Nokia Beijing Laboratory Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 Client: Nokia Corporation Beijing Economic and Technological Development Area No.5 Donghuan Zhonglu Beijing PRC China 100176 Tel. +86 10 8711 8888 Fax. +86 10 8711 4550 Responsible test engineer: Liang Dong Product contact person: Xu Helen Measurements made by: Liang Dong Tested device: RM-733 FCC ID: QTLRM-733 IC: 661AB-RM733 Supplement reports: FCC_RM-733_01 Testing has been carried out in accordance with: 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices FCC OET Bulletin 65 (Edition 97-01), Supplement C (Edition 01-01) Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields RSS-102 Evaluation Procedure for Mobile and Portable Radio Transmitters with Respect to Health Canada’s Safety Code 6 for Exposure of Humans to Radio Frequency Fields IEEE 1528 - 2003 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Technique Documentation: The documentation of the testing performed on the tested devices is archived for 15 years at TCC Nokia. Test results: The tested device complies with the requirements in respect of all parameters subject to the test. The test results and statements relate only to the items tested. The test report shall not be reproduced except in full, without written approval of the laboratory. Date and signatures: For the contents: Nokia ____________________________________________________________________________ SAR Report SAR_Photo_RM-733_02 Applicant: Nokia Corporation Type: RM-733 Copyright  2010 TCC Nokia 2/4 CONTENTS 1. SUMMARY OF SAR TEST REPORT ............................................................................................................................................. 3 1.1 TEST DETAILS ............................................................................................................................................................................. 3 1.2 PICTURE OF THE DEVICE .............................................................................................................................................................. 3 1.3 TEST POSITIONS ......................................................................................................................................................................... 3 1.3.1 Against Phantom Head ...............................................................................................…

Text truncated - open the document above for the full version.