QW3-BTGPS02Bluetooth GPS Receiver

Quick User’s Guide Introduction The Bluetooth GPS receiver uses Bluetooth wireless transfer technology and the built-in active antenna to provide a high-sensitivity signal tracking function. This device allows users to transfer data via satellite to PDA’s, smart phones and notebook PCs equipped with a Bluetooth transfer interface. The scope of application covers vehicle navigation, security systems, GIS and other related fields. Package Check the contents in the package before use. 1. Bluetooth GPS receiver 2. Car charger 3. User’s manual Overview External Antenna In Power Switch DC In Bluetooth Status Indicator GPS Status Indicator Battery Status Indicator LED Indication Indicator Status Change Status Flashing Battery low Always on Bluetooth connected Blue LED Bluetooth Connection Off Bluetooth disconnected Flashing (once per second) GPS Position Fix Green LED GPS Connection Flashing (once every 4 seconds) GPS Position Fixing Flashing Charging started; determining battery condition Always on Charge in progress Red LED Power Off Charge inactive Using an external antenna This device is equipped with a built-in antenna and does not need additional an antennal for running the GPS. You will need an external antenna to help you search and receive signals only when the device is blocked from receiving satellite signals. Getting started Step 1: Charging your battery 1. You must charge the battery before using the device for the first time. Please charge the battery with the car charger that comes with the device. After connecting the charger to the device, the red LED indicator on the device will flash because while it determines the type of battery installed on the device. After determining the battery, the charging process will start, and the red LED indicator will be illuminated at all times until the battery is fully charged. 2. When the battery is fully charged, the red LED indicator will go out. Caution! 1. The blue LED will flash at all times if the battery is low. 2. Do not charge non-chargeable batteries, as this will damage the product. Step 2: Bluetooth connection 1. Switch on your Bluetooth GPS receiver. The battery indicator (red LED) will go out. 2. Enable the Bluetooth device on your PDA or notebook PC according to the instructions. Then connect it to the Bluetooth GPS receiver. 3. The Bluetooth indicator (blue LED) is always ON if it is successfully connected to your PDA or notebook PC. You can confirm the connection with the Bluetooth software on your PDA or notebook PC. The Bluetooth indicator (blue LED) will go out if there is not connection. Caution! Some Bluetooth devices require an authorization code. This code is “0000”. Step 3: GPS 1. The GPS indicator (green) will keep flashing during positioning and after positioning is completed. Confirm positioning from your navigation software before use. 2. The GPS indicator will be illuminated at all times when the GPS is inactive. FCC Statement The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. User Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. To comply with FCC RF exposure requirement, this device and its antenna must be not co-located or operating in the conjunction with any other antenna or transmitter. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.. Other trademarks and trade names are those of their respective owners.

SPORTON International Inc. PAGE NUMBER : A1 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255

Label Information Bluetooth GPS Receiver Model No.: FB-GP02 Label Location

SPORTON International Inc. PAGE NUMBER : A4 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A5 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A6 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A7 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A8 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A9 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A10 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A11 OF A11 TEL : 886-2-2696-2468 ISSUED DATE : Oct,20,2005 FAX : 886-2-2696-2255

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw FCC RADIO TEST REPORT Applicant’s company Formosa Teletek Corporation Applicant Address No. 358, Hwaya 2nd Gueishan Shiang, Taoyuan, Taiwan FCC ID QW3-BTGPS02 Manufacturer’s company Formosa Teletek Corporation Manufacturer Address No. 358, Hwaya 2nd Gueishan Shiang, Taoyuan, Taiwan Product Name Bluetooth GPS Receiver Brand Name Formosa Teletek Model Name FB-GP02, B-Speech-GPS 2 Test Rule Part(s) 47 CFR Part 15 Subpart C15.247 Test Freq. Range 2400 ~ 2483.5MHz Receive Date Oct. 04, 2005 Test Date Oct. 14, 2005 Submission Type Original Equipment Statement The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Lab Code: 200079-0 Report No.: FR5O0409 FCC ID: QW3-BTGPS02 Page No. : i of ii Issued Date : Oct. 19, 2005 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................3 3.3. Table for Filed Antenna.......................................................................................................................................................................3 3.4. Table for Carrier Frequencies .............................................................................................................................................................3 3.5. Table for Test Modes ...........................................................................................................................................................................4 3.6. Table for Testing Locations..................................................................................................................................................................4 3.7. Table for Supporting Units ...................................................................................................................................................................4 3.8. Table for Parameters of Test Software Setting .....................................................................................................................................4 3.9. Test Configurations .............................................................................................................................................................................5 4. TEST RESULT ..................................................................................................................................................... 6 4.1. AC Power Line Conducted Emissions Measurement...........................................................................................................................6 4.2. Maximum Peak Output Power Measurement .....................................................................................................................................7 4.3. Hopping Channel Separation Measurement .....................................................................................................................................9 4.4. Number of Hopping Frequency Measurement.................................................................................................................................14 4.5. Dwell Time Measurement..................................................................................................................................................................16 4.6. Radiated Emissions Measurement ....................................................................................................................................................23 4.7. Band Edge Emissions Measurement .................................................................................................................................................37 4.8. Antenna Requirements .....................................................................................................................................................................40 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 41 6. SPORTON COMPANY PROFILE ........................................................................................................................ 43 6.1. Test Location.....................................................................................................................................................................................43 7. CERTIFICATE OF NVLAP ACCREDITATION ......................................................................................................... 44 APPENDIX A. PHOTOGRAPHS OF EUT.........................................................................................................A1 ~ A11 A…

Text truncated - open the document above for the full version.

Report No.: FR5O0409 Page No. : 1 of 3 Appendix B. Test Photos Report No.: FR5O0409 Page No. : 2 of 3 1. Photographs of Radiated Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR5O0409 Page No. : 3 of 3 TEST FIXTURE FRONT VIEW TEST FIXTURE REAR VIEW