QY9-SABRE1WEWIDEYE SABRE 1

For Alpha Only 1-1 Quick Start User Guide for SABRE™ I 1. Inserting SIM card and Battery 1.1 Inserting the SIM Card I. Insert the SIM card (gold-contacts facing downwards) into the SIM slot. II. Ensure the SIM card is inserted in the position as shown. 1.2 Inserting the Battery I. Insert the battery in the direction as shown. II. Slide in the battery door and ensure that it is locked into position. SIM Card SIM Card BatteryBattery Door 1-2 For Alpha Only 1.3 Charging the Battery I. Insert the AC/DC Power Adapter connector into the Charger socket. II. Switch on the main power. III. Do not remove the battery from the SABRE™ I during charging. IV. When the battery is fully charged, remove the AC/DC Adapter connector from the Charger Socket. Note: It takes approximately 3 hours to fully charge the battery. Note: When the SABRE™ I Terminal is switched ON, the charging time will be longer. Note: An animated icon to show that the internal battery of the SABRE TM I Terminal has completed charging while the SABRE TM I Terminal is non-operational (switched off). Note: An animated icon to show that the internal battery of the SABRE TM I Terminal is undergoing charging while the SABRE TM I Terminal is non-operational (switched off). Charger socket AC/DC Power Ada pter connector For Alpha Only 1-3 Built-in Compass LCD Up Button Enter Button Return Button Down Button Main Display Area Bottom Status Area Top Status Area Phone Port On/Off Switch Charger Socket Ethernet Port 1-4 For Alpha Only 2 Powering Up and Registering to Network 2.1 Powering Up I. Press and hold the On/Off switch for at least 3 seconds II. The LCD display will show the Introductory screen. 2.2 Terminal and SIM PINs (4 to 8 digits) I. Enter the Terminal PIN number. (Default Terminal PIN: 0000) (Note: If the Pin is entered incorrectly or if user forgets the terminal’s Pin number, send the unit back to the distributor) II. Enter the SIM PIN number. For Alpha Only 1-5 (Note: If the SIM PIN is entered incorrectly after 3 attempts, the PIN will be locked. Use the PUK (Personal Unblocking Key) code to enter new SIM PIN. If the PUK code is entered incorrectly after 10 attempts, the SIM will be disabled. Contact the Service Provider.) 2.3 GPS Fix I. For first time use, SABRE™ I needs to acquire the GPS coordinates, go to an outdoor location and have the SABRE™ I face up to the sky. The terminal shall perform the GPS acquisition automatically. II. When acquisition is done, the LCD display will show New GPS fix for 2 seconds. III. LCD will indicate the new estimated azimuth direction and elevation angle that the antenna should point. A GPS indicator will be displayed on the Top Right corner of the LCD display to indicate that a New GPS coordinate is in use. 1-6 For Alpha Only IV. For subsequent use, the SABRE™ I will not acquire a new GPS, it will prompt the user if the previously stored GPS coordinates should be used. To use the stored GPS coordinates, use the Up/Down buttons to select Yes and press ENTER. A GPS indicator will indicate the use of stored GPS coordinates. To re-acquire a new GPS, select No and press ENTER. The SABRE™ I terminal will repeat Step I to III. V. Press the ENTER button then the LCD will show the signal strength bar. 2.4 Antenna Pointing I. SABRE™ I is now in Antenna Pointing state. II. To obtain the maximum possible signal strength, adjust the antenna by turning and tilting it. For an acceptable services to commence, a signal For Alpha Only 1-7 strength of minimum 45 dBHz is required. Press ENTER when the maximum possible signal strength is obtained. III. SABRE™ I will start the registration with the network. IV. When registration is successful, the service provider’s name will be displayed. Tu r n ing Tilt ing 1-8 For Alpha Only 3 Making Phone Calls 3.1 Using Corded Analog Handset I. Connect the Corded Analog Phone to SABRE™ I via the RJ11 phone port. II. Making phone calls directly – a. Corded Analog Handset: Press the to listen dial-tone before dialing and dial the calling party number in the following format; <00><Country Code><Telephone Number><#> III. Making phone calls via Phonebook – a. Use the Up/Down buttons to select For Alpha Only 1-9 b. Scroll to the calling party’s name and Press ENTER. c. Press the button of the Corded Analog Handset to listen dial- tone. d. Use the Up/Down buttons to select . e. Press ENTER to start the dialing sequence. 3.2 Using the Bluetooth Headset I. Perform the pairing and connection procedures before proceeding with the following. (Bluetooth device pairing and connection procedures are found in Section 6 Bluetooth Settings on SABRE™ I) II. Making phone calls via Phonebook – Use the Up/Down buttons to select . 1-10 For Alpha Only a. Scroll to the calling party’s name and Press ENTER. b. Press the Connect button of the Bluetooth Headset to listen dial-tone. c. Use the Up/Down buttons to select . Connect button For Alpha Only 1-11 d. Press ENTER to start the dialing sequence. 3.3 Using the Bluetooth Handset I. Perform the pairing and connection procedures before proceeding with the following. (Bluetooth device pairing and connection procedures are found in Section 6 - Bluetooth Settings on SABRE™ I) II. Making phone calls directly – a. Bluetooth Handset: Enter the calling party number in the following format; <00><Country Code><Telephone Number> (Calling numbers will be displayed in the LCD). b. Press the button to start the dialing sequence. III. Making phone calls via Bluetooth Handset Phonebook (To be Available) 1-12 For Alpha Only 4 Installing PC programs (For Alpha) I. Insert the Product CD into the PC and go to CD Drive. II. The following drivers and application are available on the CD for installation: a. Ethernet driver b. Bluetooth Dongle driver c. BGAN LaunchPad. III. If BGAN LaunchPad is selected, follow the installer’s instructions. a. When prompted for the BGAN LaunchPad edition, select Personal Edition. b. Continue to follow the instructions until installation is com…

Text truncated - open the document above for the full version.

Federal Communication Commission Notice FCC Identifier: QY9-SABRE1WE USE CONDITIONS: This device complies with part 15 of the FCC Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. IMPORTANT NOTE : EXPOSURE TO RADIO FREQUENCY RADIATION This Device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. The Antenna used for this transmitter must be installed to provide a separation distance of atleast 100cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter FCC CAUTION : Any Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by FCC , to operate this satellite terminal Wideye SABRE I Industry Canada Statement: IC Identifier : 5023A-SABRE1WE This device complies with Radio standard specification RSS –210 & RSS –170 of Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any intereference received, including interference that may casue undesired operation. IMPORTANT NOTE : Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This antenna used for this transmitter must be installed to provide a separation distance of at least 100cm from all persons andmust not be co-located or operating in conjunction with any other antenna or transmitter. Safety Summary 1 The following general safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the equipment. Addvalue assume no liability for the customer's failure to comply with these requirements. Do Not Operate in an Explosive Atmosphere Do not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard. Keep Away from Live Circuits Operating personnel must not remove equipment covers. Component replacement and internal adjustment must be made by qualified maintenance personnel. Do not replace components with the power cable connected.Under certain conditions, dangerous voltages may exist even with the powercable removed. To avoid injuries, always disconnect power and discharge circuits before touching them Do Not Service Alone Do not attempt internal service or adjustments unless another person, capable of rendering first aid resuscitation, is present. Do Not Substitute Parts or Modify Equipment Because of the danger of introducing additional hazards, do not substitute parts or perform any unauthorized modification to the equipment. Keep Away from Active Antenna Front This device emits radio frequency energy when in transmit mode. To avoid injury, keep a minimum safety distance of 1meter from the antenna front. See also the below section Antenna Safety Instructions. CAUTION Risk of Explosion if Battery is Replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. Batteries and Accessaries Use Addvalue approved batteries and accessories only . Use of non-approved batteries and accessories may result in loss of performance , damage to Satellite Terminal, explosion, fire, electrical shock or injury. Antenna Safety Instructions 2 Antenna Minimum Safe Distance: 100 cm Radiation Warning High levels of radio frequency radiation are considered health hazardous. Although no single value of “ safe radiation level “ has been agreed upon by all countries ,the American National Standards Institute ( ANSI/LEEE C 95.1-1992) recommends that people should not exposed to radiation stronger than 1 milliwatt per square centimeterat the frequencies used in the Addvalue’s Wideye SABRE I terminal. Accordingly ,the operator of the terminal should ensure that the area extending 1meter from the Front of the antenna be kept clear of personnel when the terminal is transmitting. The antenna is built-in within SABRE™ I. You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use. Transmit only when person(s) are at least the minimum distance from the front face of the antenna. WARNING! Maintain a separation distance from the antenna to a person(s) of at least 100 c…

Text truncated - open the document above for the full version.

Rev 1.10 Proprietary Information Not To Be Disclosed Without Written Authorization From AVC © Addvalue Technologies Ltd, all rights reserved 1 1.2.21.1.1System Architecture The proposed system architecture block diagram is shown inFigure 1Figure1Figure 1Figure1Figure1Figure1. It comprises an Antenna section (BGAN & GPS), an RF section (TX and RX), a Baseband Processing & Channel Unit, a GPS Module, an Embedded System module, and a Power Unit with power up sequencing scheme for high power RF circuit protection. High-level internal and external interfaces are shown in . Technical details for the various functional blocks are described in the subsequent sections. Antenna Unit GPS Power Unit Battery and Charger I/Q Modulator I/Q Demodulator DDS Baseband and Channel Unit Framing DAC ADCDDC Timing Turbo decoder Scrambler Turbo coder De-scrambler USB Client UICC (SIM/USIM) Embedded System Bluetooth ready USB Host SLIC Peripheral Memory ARM9 HW RTOS Network Stacks Peripheral Drivers SW Protocol Stack M.M. Interface Down Converter Up Converter AGCLNA PA Filter Filter RF PWR Detector RF section DSP Figure 1: Pocket Size BGAN UT System Architecture Simplified Block Diagram Formatted: Bullets and Numbering Field Code Changed Proprietary Information Not To Be Disclosed W ithout Written Authorization From AVC © Addvalue Technologies Ltd, all rights reserved 2 Satellite LNA & RF/IF Satellite HPA & RF/IF Duplex Filter Satellite Antenna Tx (1626.5 - 1660.5 MHz) Rx (1525.0 - 1559.0 MHz) IF @ 75 M Hz <15:0> Data <15:0> Block Valid Sys CLK@ 26.88 MHz CData <7:0>,inout CData <7,0> inout CS_Tx, RD,WR,ADDR<2:0> CHANNEL PROCESSING Forward Link Channel de-Interleaving, Turbo Decoding Descrambling Return Link Scrambling, Turbo Coding, Channel Interleaving Dual Port RAM USB BlueTooth Module GPS Module RF/IF Front End RF/IF & LNA RF 1.575 GHz RF/IF Control Signals Digital Front End In: Auto Sensing 240 V ac (50Hz) or 120 V ac (60Hz) Out: Power Supply DC in 10-18V ChargerBattery FLASH ( ~ 1.909 Mbyte) SRAM ( ~ 328K Byte + 6Kword) Addr Bus<15:0>,Data Bus<15:0>, IRQ, RD, WR RJ45 USB Interface Connection to Terminal Equipment SIM CARD Interface I 2 S I 2 S Audio Signal 2-wire interface (RJ-11) 2 wire PSTN handsets DAC & 4 kHz Filter ADC & 4 kHz Filter Pow er Low Batt An tenna Position SL IC C PU OPMAP1510 (Dual Core Architecture- ARM-925 & TMS320C55x) GPS UART RF/IF Front End Control I/O Digital Front End Control I/O Addr & DATA BUS Ethernet (802.3) Controller I/O USB 1.1 Client UICC/USIM DSP Audio Codec AM BE+2 (DVSInC) T MS320C55x DSP Core LED Control I/O System DMA Rev : 0.4 Date: 26 Aug, 2003 **Connection to BGAN Test Equipment For Testing only RF 2.4 - 2.48 GHz PLL (Data,CLK,CS_Tx,CS_Rx,LD) Power Level A/D Power Level D/A Tx_Enable Rx_Enable CS_Rx, RD,WR,ADDR<2:0 > I/Q D/A <15:0> I/Q A/D f s @ 53.76 M Hz OC XO 26.88 MHz Data_PLL LD_PLL CLK_PLL CS_PLL_Tx CS_PLL_Rx Tx_Enable Rx_Enable P ow er Level A/D Power Level D/A Sys C LK@ 26.88MHz CData <7,0> Addr <2:0> RD WR CS_Tx CS_Rx I <7:0> iqdm_dv Frame_Flag Coding Rate Flag Q <7:0> Sys CLK @26.88MHz 12 MHz 32.768 KHz Demodulator DownLink (Rx) (QPSK, 16-QAM) Modulator UpLink (Tx) (16-QAM, Pi/4 QPSK) f s @ 53.76 M Hz IF @ 60 M Hz GPS Antenna V+ V- BT Ready USB 1.1 Host Proprietary Information Not To Be Disclosed W ithout Written Authorization From AVC © Addvalue Technologies Ltd, all rights reserved 3 Figure2: Pocket Size BGAN UT System Architecture Figure23: Pocket Size BGAN UT System Architecture S atellite LNA & R F /IF S atellite HPA & R F /IF D u plex F ilt e r Satellite Antenna Tx (1626.5 - 1660.5 MH z) Rx (1525.0 - 1559.0 MH z) IF @ 10 .8 M H z <1 5:0> D ata <15:0> B lock V alid Sys CLK@ 24.192MH z C D a ta <7:0>,inout C D ata <7,0> in ou t C S _ T x, R D,W R ,ADD R<2:0> CHANNEL PROCESSING Forward Link Channel de-Interleav ing, Turbo D ecoding D escram bling R eturn Link Scram bling, Turbo C oding, C hannel Interleaving D ual P ort RA M USB BlueTooth Module G P S M o d u le R F/IF F ront En d LNA RF 1.575 GH z R F/IF C on trol Sig nals D igital Front End In: A uto S ensin g 240 V ac (50Hz) or 120 V ac (60Hz) O ut: Pow er Su pp ly D C in 10-18V ChargerBattery FLA SH ( ~ 1 .9 0 9 M byte) SRAM ( ~ 328K Byte + 6K w ord ) Addr Bus<15:0>,D ata B us<15:0>, IRQ , R D, W R RJ45 USB Interface C onnection to Term inal E quipm ent SIM CARD Interface I 2 S I 2 S Audio S ignal 2-w ire interface (RJ-11) 2 wire P STN handsets DAC & 4 kHz Filter ADC & 4 kHz Filter P ower Low B a tt Antenna Position S L IC C PU OPM AP1510 (Dual C ore Architecture- AR M-925 & TM S320C 55x) GPS UART R F/IF F ront End C ontrol I/O D igital Front E nd C ontrol I/O Addr & DA TA BU S Ethernet (802.3) C ontro ller I/O USB 1.1 C lient U IC C /U S IM D SP Audio Codec AM BE+2 (D VSInC) TM S320C55x DSP C ore LE D Control I/O Sy stem DMA R ev : 0.4 D ate: 25 Sep, 2003 **C onnection to B G AN Test Equipm ent For Testing only RF 2.4 - 2.48 G H z P L L (D a ta,C L K,C S _T x,C S _ R x,LD ) P ow er L evel A/D P ow er L evel D/A T x_E n able R x_Enable C S _R x, RD ,W R ,ADD R<2:0 > I/Q D /A <15:0> I/Q A /D f s @ 9.678M Hz VC -TC XO 24.192 MHz D ata_P L L LD_PLL C LK_PLL CS_PLL_Tx C S_PLL_Rx Tx_Enable R x_Enable Pow er Leve l A/D Pow er L eve l D/A Sys CLK@ 24.192MHz C Data <7,0> A dd r <2:0> RD WR CS_Tx C S_Rx I <7:0> iqdm _dv Fram e_Flag C oding R ate Flag Q <7:0> Sys C LK @ 26.88MHz 12 M Hz 32.768 K Hz Dem odulator DownLink (Rx) (QPSK, 16-QAM) M odulator UpLink (Tx) ( P i/4 Q P SK ) f s @ 12.096M Hz IF @ 71M hz G PS Antenna V+ V- B T Ready U SB 1.1 H ost

Attention:Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE:CONFIDENTIALITY REQUEST FOR WIDEYE-SATELLITE BROADBAND COMMUNICATOR, SABRE I FCC ID:QY9-SABRE1WE To Whom It May Concern: This letter serves as an official request for confidentiality under FCC Rule Sections 0.457 (d) (1) (ii) and 0.459. We have requested that the schematic diagrams & theory of Operation required to be submitted with this application be withheld from public review. It contains intellectual property of our company and making it public will hinder the competitiveness of the product. Please contact me if there is any information you may need. Sincerely, Signature Prabakar Kuttaniseeri, November 27, 2006 Assistant Manager

Attention:Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE:LETTER OF AGENT AUTHORIZATION FCC ID:QY9-SABRE1WE To Whom It May Concern: We, the undersigned, hereby authorize TUV SUD PSB Corporation Pte Ltd. To act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature Prabakar Kuttaniseeri , November 27, 2006 Assistant Manager

Test Report No. 53S062852/EMC/06 dated 29 Nov 2006 EUT PHOTOGRAPHS / DIAGRAMSANNEX A Addvalue Communications Pte LtdPage 70 of 91 Satellite Broadband Communicator [ Model : Sabre I ] [ FCC ID : QY9-SABRE1WE ] EUT PHOTOGRAPHS - SATELLITE BROADBAND COMMUNICATOR Front View Rear View Test Report No. 53S062852/EMC/06 dated 29 Nov 2006 EUT PHOTOGRAPHS / DIAGRAMSANNEX A Addvalue Communications Pte LtdPage 71 of 91 Satellite Broadband Communicator [ Model : Sabre I ] [ FCC ID : QY9-SABRE1WE ] EUT PHOTOGRAPHS - SATELLITE BROADBAND COMMUNICATOR Top View Bottom View

Test Report No. 53S062852/EMC/05 dated 28 Nov 2006 FCC LABEL & POSITION ANNEX B Addvalue Communications Pte LtdPage 81 of 83 Satellite Broadband Communicator [ Model : Sabre I ] [ FCC ID : QY9-SABRE1WE ] Labelling requirements per Section 2.925 & 15.19 The label shown will be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. FCC ID Sample Label FCC Statement Sample Label Test Report No. 53S062852/EMC/05 dated 28 Nov 2006 FCC LABEL & POSITION ANNEX B Addvalue Communications Pte LtdPage 82 of 83 Satellite Broadband Communicator [ Model : Sabre I ] [ FCC ID : QY9-SABRE1WE ] Physical Location of FCC Label on EUT FCC ID Label FCC Statement

Project ID: lotusBOM Name: SABRE 1-V1 Release Date: 05/03/07 BILL OF MATERIAL Revision : 105 S/N ITEM P/N REV NO DESCRIPTION LOCATION QTY UOM MFG MFG P/N 1ST S.V. 2nd MFG 2nd MFG P/N 2ND S.V. 1 10B101F6105 105 Final Packaging for BGAN Terminal, Sabre 1-V1 1 SET NA NA NA 2 44A41282010 Label, Serial Barcode Label, Lotus, Self-Adhesive Thermal Transfer Polyester, (44x17x0.076)mm 1 PCS ID LABEL ID LABEL 3 44A41283010 Label, Shipment Label, Lotus, Thermal Transfer Polyester, (70.0x60.0x0.076)mm 0.666 PCS ID LABEL ID LABEL 4 45C90235100 Bulk Packaging, Shipping Box, I/D:(465x391x418)mm 0.333 PCS Prelude Printing (M) Sdn Bhd Prelude Printing (M) Sdn Bhd 5 12A201F9104 104 Packaging / Accessory for BGAN Terminal, Sabre 1- V1 1 SET NA NA NA 6 35B24010004 Power Adapter Switching, AC-DC, 100-240VAC, 50/60Hz, 2 pin I/P plug, 15VDC, 2.8A, Straight DC jack, (+,-), (ID=2.1mm, OD=5.5mm, L=1828mm) 1 PCS DVE SB1/SPA QPACP Pte Ltd 7 38280510010 Box Handle, Lotus, ABS, Black, (152x18x4)mm 1 PCS Prelude Printing (M) Sdn Bhd 38280510010 Prelude Printing (M) Sdn Bhd 8 44A41282010 Label, Serial Barcode Label, Lotus, Self-Adhesive Thermal Transfer Polyester, (44x17x0.076)mm 1 PCS ID LABEL ID LABEL 9 44J41291030 Label, Order Code Label, Lotus, Self-Adhesive Thermal Transfer Polyester, (60x18x0.076)mm 1 PCS ID Label ID Label 10 45A90214010 PE Bag, General, PE Clear, (400x240{open}x0.06)mm 1 PCS Asia Plastic Asia Plastic 11 45A90215010 Zip Bag, General, PE Clear, (220x135{open}x0.06)mm 1 PCS Asia Plastic Asia Plastic 12 45B90234100 Product Packaging, Pretty Box, I/D:(370x150x385)mm 1 PCS Prelude Printing (M) Sdn Bhd Prelude Printing (M) Sdn Bhd 13 45H90232100 Top Polyfoam, Cushioning, EPE Foam, Pink, (370x360x70)mm 1 PCS Jebson & Jessen Broadway (M) Sdn Bhd Prelude Printing (M) Sdn Bhd 14 45H90233100 Bottom Polyfoam, Cushioning, EPE Foam, Pink, (370x360x70)mm 1 PCS Jebson & Jessen Broadway (M) Sdn Bhd Prelude Printing (M) Sdn Bhd 15 45J90228030 Product Packaging, Foam Sleeve, (370x360x140)mm 1 PCS Prelude Printing (M) Sdn Bhd Prelude Printing (M) Sdn Bhd 16 45M90230030 Product CD Cover 1 SET Sonopress Singapore Sonopress Singapore 17 50C01120526 Internal Battery Pack 1 SET Totex International Ltd SB1/PBATT Totex International Ltd 18 53N40000112 Cable Pack, IP44-Compliant, (8P4C RJ45 CAT.5 Network Cable-1.5m, 6P4C RJ11 Telephone Cord-1.8m, Type A/B USB Cable-1.5m), Pantone Warm Grey 1C 1 SET Vizion Technologies Pte Ltd SB1/CABLEPK Vizion Technologies Pte Ltd 19 53P10000113 Power Cord, ( EURO,US,UK Type ) (1.8m) 1 SET Lian Dung SB1/PCPK Mapconn (Singapore) Pte Ltd 20 74B00110111 Quick Start Guide (Printed). 0 PCS 21 87A89042030 Product CD (Inclusive of drivers,launch pad & all documentations). 1 SET Sonopress Singapore Sonopress Singapore 22 15Q001F9103 103 Assembly for BGAN Terminal, Sabre 1-V1 1 SET NA NA NA FRM-DC-00-002 Rev 2 Proprietary Information Not To Be Disclosed Without Authorization From bomh.logofile Addvalue Technologies Ltd, all right reserved Page 1 OF 30 23 36H70024100 Membrane Keypad, Lotus,Plastic, 4 contacts, (69x22.5x0.6)mm 1 PCS Central-Midori (Int'l) Pte Ltd Central-Midori (Int'l) Pte Ltd 24 37B77258001 Housing Battery Contact, Lotus, Stainless Steel (SUS304), (29.0x6.0x0.2)mm 3 PCS Mostly Strong Mostly Strong 25 37C77297100 Bottom Housing, Lotus, Magnisium Alloy AZ91D, Pantone Cool Grey 10M, Matt Finish, High Baked Paint, (255x165x5)mm 1 PCS A B Technology (M) Sdn Bhd A B Technology (M) Sdn Bhd 26 37D77289030 Baseband Shield, Lotus, Aluminium, (174x114x5)mm 1 PCS Beyonics Precision Engineering Pte Ltd Beyonics Precision Engineering Pte Ltd 27 37D77290030 RF Shield, Lotus, Aluminium, (133x114x9.8)mm 1 PCS Beyonics Precision Engineering Pte Ltd Beyonics Precision Engineering Pte Ltd 28 37F77274010 Contact Spring, Lotus, Stainless Steel (SUS304), (18.0x12.0 x 0.2)mm 1 PCS Mostly Strong Mostly Strong 29 37P77292031 RF Heatsink, Lotus, Aluminium, (206x125x19)mm 1 PCS Beyonics Precision Engineering Pte Ltd Beyonics Precision Engineering Pte Ltd 30 37T77268010 Swivel Hinge, Lotus, Aluminium, Pantone Cool Grey 10M, Matt Finish, Powder Coated, (82.0x25.0x30.0)mm 1 PCS SOUTHCO CT-3420-00 SOUTHCO 31 37W77275010 UT Stand, Lotus, Magnisium Alloy AZ91D, Pantone Cool Grey 10M, Matt Finish, High Baked Paint, (255.0x165.0x16.0)mm 1 PCS A B Technology (M) Sdn Bhd A B Technology (M) Sdn Bhd 32 38A80523100 Top Housing, Lotus, PC/ABS, Pantone Cool Grey 7M, Matt Finish, (258x185x42)mm 1 PCS Sanichi Precision Plastic Sdn Bhd Sanichi Precision Plastic Sdn Bhd 33 38E80524100 Battery Door, Lotus, PC/ABS, Pantone Cool Grey 7M, Matt Finish, (30x53x21)mm 1 PCS Sanichi Precision Plastic Sdn Bhd Sanichi Precision Plastic Sdn Bhd 34 38G80493010 Speaker Holder, Lotus, PC, Transparency, (33.7x24.5x10.5)mm . 1 PCS Sanichi Precision Plastic Sdn Bhd Sanichi Precision Plastic Sdn Bhd 35 38N80517030 Display Lens, Lotus, PC, Transparency, (68.8x22.5x1.8)mm 1 PCS Sanichi Precision Plastic Sdn Bhd Sanichi Precision Plastic Sdn Bhd 36 39A55000088 Screw, Pan Head (Phillips), Stainless Steel, M2x10 mm 33 PCS Coffer Industrial Supplies SMSSPS-M2PP010 Coffer Industrial Supplies 37 39A55000089 Screw, Pan Head (Phillips), Stainless Steel, M2x3 mm 2 PCS Coffer Industrial Supplies SMSSPS-M2PP003 Coffer Industrial Supplies 38 39A55000090 Screw, Pan Head (Phillips), Stainless Steel, M2x4 mm 4 PCS Coffer Industrial Supplies SMSSPS-M2PP004 Coffer Industrial Supplies 39 39A55000092 Screw, Pan Head (Phillips), Stainless Steel, M3x6 mm 5 PCS Coffer Industrial Supplies SMSSPS-M3PP006 Coffer Industrial Supplies 40 39A55000093 Screw, Pan Head (Phillips), Stainless Steel (Black), M4x10 mm 4 PCS Coffer Industrial Supplies SMSSPS-M4PP010 Coffer Industrial Supplies 41 39A55000095 Screw (Self-Tapping), Pan Head Type B (Phillips), Steel, Blue Zinc Plating, 2.6x5.0 mm 4 PCS Coffer Industrial Supplies STSTZB-M2.6PP005BS1 Coffer Industrial Supplies 42 39A55000102 Screw, Pan Head (Torx), Rubber O-Ring Attached (Black) (Thickness=1mm), Stainless Steel (Black), M4x1…

Text truncated - open the document above for the full version.

Test Report No. 53S062852/EMC/05 dated 28 Nov 2006 Note: This report is issued subject to TÜV SÜD PSB Corporation's "Terms and Conditions Governing Technical Services". The terms and conditions governing the issue of this report are set out as attached within this report. LA-2001-0212-A LA-2001-0213-F LA-2001-0214-E LA-2001-0215-B LA-2001-0216-G LA-2001-0217-G LA-2006-0355-C The results reported herein have been performed in accordance with the laboratory’s terms of accreditation under the Singapore Accreditation Council - Singapore Laboratory Accreditation Scheme. Tests/Calibrations marked "Not SAC-SINGLAS Accredited" in this Report are not included in the SAC-SINGLAS Accreditation Schedule for our laboratory. Laboratory: TÜV SÜD PSB Corporation Pte. Ltd. Testing Group No.1 Science Park Drive Singapore 118221 Phone : +65-6885 1333 Fax : +65-6776 8670 E-mail: [email protected] www.psbcorp.com Co. Reg : 199002667R Regional Head Office: TÜV SÜD Asia Pacific Pte. Ltd. 3 Science Park Drive #04-01/05 The Franklin Singapore 118223 Page 1 of 83 FORMAL REPORT ON TESTING IN ACCORDANCE WITH FCC Parts 15B & C : 2006 OF A SATELLITE BROADBAND COMMUNICATOR [ Model : SABRE I ] [ FCC ID : QY9-SABRE1WE ] TEST FACILITY TÜV SÜD PSB Corporation Pte Ltd, Telecoms & EMC, Testing Group, 1 Science Park Drive, Singapore 118221 FCC REG. NO. 90937 (3m & 10m OATS) 99142 (10m Anechoic Chamber) 871638 (5m Anechoic Chamber) 325572 (10m Anechoic Chamber) IND. CANADA REG. NO. IC 4257 (3m and 10m Anechoic Chambers) PREPARED FOR Mr Prabakar Kuttaniseeri Addvalue Communications Pte Ltd 190 Changi Road #02-02 MDIS Building Singapore 419974 Tel : (65) 6342 5420Fax : (65) 6342 5426 QUOTATION NUMBER 53Q0601508 & 56Q0601375 JOB NUMBER 53S062852 & 56S061092 TEST PERIOD 20 Oct 2006 – 04 Nov 2006 & 22 Nov 2006 - 25 Nov 2006 PREPARED BYAPPROVED BY ____________________ Quek Keng Huat Associate Engineer ____________________ Lim Cher Hwee Assistant Vice President Test Report No. 53S062852/EMC/05 dated 28 Nov 2006 Addvalue Communications Pte LtdPage 2 of 83 Satellite Broadband Communicator [ Model : Sabre I ] [ FCC ID : QY9-SABRE1WE ] TABLE OF CONTENTS TEST SUMMARY PRODUCT DESCRIPTION SUPPORTING EQUIPMENT DESCRIPTION EUT OPERATING CONDITIONS CONDUCTED EMISSION TEST RADIATED EMISSION TEST CARRIER FREQUENCY SEPARATION TEST SPECTRUM BANDWIDTH (20dB BANDWIDTH MEASUREMENT) TEST NUMBER OF HOPPING FREQUENCIES TEST AVERAGE FREQUENCY DWELL TIME TEST MAXIMUM PEAK POWER TEST RF CONDUCTED SPURIOUS EMISSIONS TEST BAND EDGE COMPLIANCE (CONDUCTED) TEST BAND EDGE COMPLIANCE (RADIATED) TEST PEAK POWER SPECTRAL DENSITY TEST MAXIMUM PERMISSIBLE EXPOSURE (MPE) TEST DUTY CYCLE FACTOR COMPUTATION ANNEX A- EUT PHOTOGRAPHS / DIAGRAMS ANNEX B- FCC LABEL & POSITION ANNEX C- USER MANUAL, TECHNICAL DESCRIPTION, BLOCK & CIRCUIT DIAGRAMS Test Report No. 53S062852/EMC/05 dated 28 Nov 2006 Addvalue Communications Pte LtdPage 3 of 83 Satellite Broadband Communicator [ Model : Sabre I ] [ FCC ID : QY9-SABRE1WE ] TEST SUMMARY The product was tested in accordance with the customer's specifications. Test Results Summary Test StandardDescriptionPass / Fail FCC Part 15: 2006 15.107(a), 15.207Conducted EmissionsPass 15.109(a), 15.205, 15.209 Radiated Emissions (Spurious Emissions inclusive Restricted Bands Requirement) Pass Carrier Frequency SeparationPass15.247(a)(1) Spectrum Bandwidth (20dB Bandwidth Measurement) Pass Number of Hopping FrequenciesPass15.247(a)(1)(iii) Average Frequency Dwell TimePass 15.247(b)(1)Maximum Peak PowerPass 15.247(d)RF Conducted Spurious EmissionsPass 15.247(d)Band Edge Compliance (Conducted)Pass 15.247(d)Band Edge Compliance (Radiated)Pass 15.247(e)Peak Power Spectral Dens…

Text truncated - open the document above for the full version.