QYELDB3-RDDE05078Tag Reader

ASK R&D Réf. : RD-ST-05065-11 1 / 12 ASK 2260 Route des Crêtes R&D001-Form1 06560 VALBONNE SOPHIA ANTIPOLIS Tel : 04 97 21 40 00 Fax : 04 92 38 93 21 USER MANUAL LDB 307 “Safe ID” ASK LDB 307 “Safe ID” reader user manual ASK R&D Réf. : RD-ST-05065-11 2 / 12 ASK 2260 Route des Crêtes R&D001-Form1 06560 VALBONNE SOPHIA ANTIPOLIS Tel : 04 97 21 40 00 Fax : 04 92 38 93 21 TABLE OF CONTENTS 1 SCOPE OF MANUAL 3 1.1 UNPACKING AND INSPECTION 3 1.2 READER COMPONENTS 4 1.2.1 Coupler board 4 1.2.2 Antenna board 6 1.2.3 Power supply board 7 1.3 Assembly 8 2 READER SETUP 9 2.1 INSTALLING A NEW SAM IN READER 9 2.2 READER CONNEXION 10 3 HOW TO USE THE READER 10 3.1 CONTACTLESS OPERATIONS 10 3.2 SOFTWARE 11 3.3 CLEANING 11 4 STANDARD COMPLIANCE 11 4.1 FCC COMPLIANCE STATEMENTS 11 4.2 CE COMPLIANCE STATEMENT 12 USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 3 / 12 Copyright ASK SA - 2003 1 SCOPE OF MANUAL This manual describes ASK LDB 307 «Safe ID» reader main features and setup information. This manual is intended for use by end users. No specific tools are required for operation described in this document. LDB 307 «Safe ID» is a contactless smart card reader compliant with the following standards : - ISO 7816 - ISO 14443 type A&B - ISO 15693 High speed protocols are supported: Up to 424 Kb/s for Type A and Type B cards. 848 Kb/s is supported using ASK qualified cards. LDB 307 «Safe ID» integrates also Philips component to read/write on Mifare® standard cards. The LDB307 is compliant with USB1.1 or USB2.0 computer interface. 1.1 UNPACKING AND INSPECTION Each LDB 307 «Safe ID» kit is shipped with : - USB cable attached (length: 0,8 meters) - This user manual - One power supply: Universal 100 ~240V AC / 12V DC 500mA or appropriate plug and mains voltage‡ 12V DC 500mA depending on purchase location. - LDB 307 «Safe ID» reader packaged in plastic case USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 4 / 12 Copyright ASK SA - 2003 LDB 307 «Safe ID» reader is a contactless reader dedicated for operators as desktop reader for passport verification, due to its specific design, but also for card issuing center, point of sales, etc... LDB 307 «Safe ID» provides the communication between a terminal and customer smart cards. 1.2 READER COMPONENTS LDB 307 «Safe ID» consists of a control board called ”coupler board”, and antenna board, a DC supply converter board (with two extra SAM sockets). A FTDI “USB to serial” interface is included 1.2.1 COUPLER BOARD The coupler board contains a microprocessor, non-volatile memory and a radio frequency transmitting circuitry. This board communicates with smart cards via RF link (provided by an antenna board), and to the terminal via “USB to serial” interface. The coupler platform is GEN327 which can be purchased separately at ASK. This OEM coupler board is compliant with ISO/IEC14443-2 directives (Radio frequency power and signal interface). Communications can be executed according to the type A or type B of the directive. USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 5 / 12 Copyright ASK SA - 2003 Figure121 : LDB 307 «Safe ID» coupler : GEN 327 SAM1 location USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 6 / 12 Copyright ASK SA - 2003 1.2.2 ANTENNA BOARD The antenna board consists of a printed circuit board with copper traces forming the transmit and the receive antenna. Antenna may be one of several types, varying in dimensions and connection. LDB 307 «Safe ID» receives GEN 535 antenna because its area (178x125mm) matches well with a passport verification application. This antenna has a tuning capacitor, but no setting is required because it has been optimized in factory. Optimal tuning is obtained when LED indicator is at its maximum illumination. Figure 22 : LDB 307 «Safe ID» antenna : GEN 535 Tuning trimmer Tuning LED indicator USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 7 / 12 Copyright ASK SA - 2003 1.2.3 POWER SUPPLY BOARD This board contains a DC-DC converter and two extra SAM locations. Input line should be from 9V to 36V DC. Typically an AC power bloc with output 12V 500mA (with or without regulation) should be used. Figure 3 : LDB 307 «Safe ID» DC conversion / SAM extension board : GEN 351 SAM location USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 8 / 12 Copyright ASK SA - 2003 1.3 ASSEMBLY Inside the plastic case these boards are stacked together ( Figure 4). Figure 4 : stacked boards in reader Power supply board USB adaptor Antenna board DC input USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 9 / 12 Copyright ASK SA - 2003 2 READER SETUP 2.1 INSTALLING A NEW SAM IN READER In most applications, one SAM (Security Application Module) or more is required. These components are provided separately, so to set a SAM, the plastic case should be opened. For opening, flip over the plastic case. You have to put a blade in the rear slot and lift the bottom of the case in order to set free a central ergot. Then the bottom of the box should be removed by sliding in the front side direction. The stacked board will appear as in Figure 4, the first SAM should be installed on coupler board GEN 32X (Erreur ! Source du renvoi introuvable.) and next SAMs should be installed on DC conversion board GEN 351 (Figure 3). Caution: In a first time, μSIM SAMs must be gently inserted in the open door socket (Figure 5), then in a second time the door should be locked. Figure 5 : SAM in open door SAM USER MANUEL LDB 307 «Safe ID» DESKTOP READER ASK R&D Réf. : RD-MU-050656-11 10 / 12 Copyright ASK SA - 2003 2.2 READER CONNEXION The reader’s USB cable should be connected to a USB computer port. You will be asked to install “USB serial port” driver located in the furnished toolkit. Suitable driver is also available on FTDI website http://www.ftdichip.com/ at the following link: http://www.ftdichip…

Text truncated - open the document above for the full version.

June 20 th , 2005 CONFIDENTIALITY REQUEST To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Curtis-Straus LLC 527 Great Rd Littleton, MA 01460 USA Re: Confidentiality request for a Low Power Communication Device FCC ID: QYELDB3-RDDE05078 Gentlemen, ASK requests, pursuant to 47CFR 0.459, post grant confidentiality for portions of the material contained in this application. The following document regarding this submission for FCC ID: QYELDB2-RDDE03082 be kept confidential 1. Schematic Diagram of LDB2 (file: GEN351rev2.1-B.pdf) 2. Schematic Diagram of LDB2 (file: GEN327rec2-4-C.pdf) 3. Schematic Diagram of LDB2 (file: RD-PL-05051-11.pdf) 4. Block diagram of LDB2 (file: Block Diagram-LDB.pdf) 5. Operational description of LDB2 (file: Oper Descr-LDB.pdf) Specifically, these exhibits contain information relating to circuit function and complexity that could be of benefit to competitors. The material contains trade secrets and confidential information that ASK does not customarily release to the public and which is otherwise not generally available to the public. Regards, Olivier PARRAULT Hardware Engineer ASK 2405 route des Dolines F-06560 VALBONNE SOPHIA ANTIPOLIS - France F Original written signature of authorized signer

Response to TCB Findings 1. Please clarify how the modifications and ferrites will be ensured on the final devices that will be supplied to the end-users. The manual must include a warning against removal of these ferrites, if they are supplied to the user already installed. If not supplied already installed, then proper instructions must be provided to the user for installation. Please clarify. The ferrites are supplied to the user already installed. See file user_manual_ldb,rev2.pdf 2. Please clarify; through what kind of connection, the antenna is connected to the transmitter board. Three pins connect the antenna to the transmitter board.

FCC ID: QYELDB3-RDDE05078 Page 1/2 EXTERNAL PHOTOS OF TESTED EUT 1.1 PHOTOS of the LDB307 General view Front face Rear face FCC ID: QYELDB3-RDDE05078 Page 2/2 Lower face

FCC ID: QYELDB3-RDDE05078 Page 1/2 1 PRODUCT LABELING 1.1 FCC ID Label This is the copy of the label stuck on the product. Dimensions: 30 x 40 mm Material: Thermic transfer on adhesive metallic polyester support. Label material and adhesive both will last the lifetime of the product. LDB 307 Type: DE-05078-11 Serial: 05240001 Made in France FCC ID: QYELDB3-RDDE05078 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation input: 12VDC 500mA FCC ID: QYELDB3-RDDE05078 Page 2/2 1.2 Location of label on EUT Label is stuck on the lower face of the reader. L D B 3 0 7 T y p e : D E - 0 5 0 7 8 - 1 1 S e r i a l : 0 5 2 4 0 0 0 1 M a d e i n F r a n c e F C C I D : Q Y E L D B 3 - R D D E 0 5 0 7 8 i n p u t : 1 2 V D C 5 0 0 m A

FCC ID: QYELDB3-RDDE05078 1 INTERNAL PHOTOS OF TESTED EUT 1.1 General views of the LSP2 Rear face, cover removed. Daughter board and RS232/USB converter removed FCC ID: QYELDB3-RDDE05078 Mother board removed FCC ID: QYELDB3-RDDE05078 1.2 Antenna views Front face Rear face FCC ID: QYELDB3-RDDE05078 1.3 Mother board views front face rear face FCC ID: QYELDB3-RDDE05078 1.4 Daughter board views FCC ID: QYELDB3-RDDE05078 1.5 Views of the power supply 1.5.1 General view 1.5.2 Internal views, cover removed Font face Rear face FCC ID: QYELDB3-RDDE05078 1.6 RS232/USB converter Front view Rear view

Actions Mesures Z.I. des Blanchisseries – 38500 VOIRON – Tél. +33(0)4 76 65 76 50 – Fax +33(0)4 76 66 18 30 – www.smee.fr S.A. au capital de 152 449,02€/ R.C. de Grenoble B 329 901 888 / SIRET 329 901 888 00035 / code APE 332 B / n°TVA :FR29 329 901 888 This test report applies only on equipment described hereafter. Proposal number: 200504-2678 Date........................................: May 7 th , 2005 Location..................................: SMEE Actions Mesures Laboratory - 38 VOIRON Performed by...........................: Jacques LORQUIN Customer.................................: ASK 15, Traverse des Brucs 06560 SOPHIA ANTIPOLIS FRANCE Product....................................: LDB307 Type of test.............................: Conducted and Radiated Emission Test Applied standards....................: ANSI C63-4 (2003) 47 CFR Part 15 Subpart C Result of tests........................: Radiated Emission : Comply Conducted Emission : Comply The reproduction of this test report is authorized only under its entire form. This report contents 19 pages. Written by................................: Jacques LORQUIN Approved by : Jacques LORQUIN EMC TEST REPORT Nr 3408-FCC Text Nr 3408-FCC May 7th, 2005 page 2 /19 1. System test configuration 1.1. Justification The system was configured for testing in a typical fashion (as a customer would normally use it). 1.2. HARDWARE IDENTIFICATION: Equipment under test (EUT): FCCID: QYELDB3-RDDE05078 ÿ LDB307 pn: DE-05078-11 sn: 05180005 - Input/output: Power supply: 12Vdc USB connector - Size: 190x135x60mm - Frequencies: 847kHzMHz; 13.560MHz, 3.68MHz 27.120MHz Bit rates: 460kB/s (no clock or signal higher than 108 MHz) 1.3. Auxiliaries The FCC IDs for all equipment, more description of all cables used in the tested system are : Trade Mark – Model Number (Serial number) FCC ID Description Cable description LDB307 pn:DE-05078-11* (sn: 05180005) QYELDB3-RDDE05078 RFID reader Power cord unshielded. USB cable shielded Compit MPP15 model:FW75550/12 (sn: none) none AC/DC Power supply Power cord unshielded. DELL Latitude D600 (sn: CNOD2125-48643-4CH-1711) D.O.C. Laptop Power cord unshielded. All other cable shielded. DELL model: PA-1650-05D (sn: CN05U092-71615-4CG-5F65) none AC/DC power supply for laptop Power cord unshielded TELEX pn: none (sn: 700373-000A) none microphone Shielded cable Philips type A none TAG Compaq 2144EA Å (sn: CN31702610) D.O.C. Laptop Power cord unshielded. All other cable shielded. Hewlett Packard Å (sn: MTT0310051940) none AC/DC power supply for laptop Power cord unshielded * : Equipment under test. Å : Auxiliaries equipement used for conducted measurements. 1.4. Equipment modifications Modifications apply on product: - A Ferrite Wurth N°742 711 32 is set inside the EUT on USB cable (2 turns). - Ferrites Wurth N°742 711 17 are set inside the EUT on power supply (1 turn) cord and on the antenna connector (see photo for more details). - A ferrite Wurth N°742 711 17 is set on the serial cable (2 turns). - 10 pF is set on antenna shield. Text Nr 3408-FCC May 7th, 2005 page 3 /19 - The two metallic plan of the antenna are connected on the shield of antenna via 2 points (see photo for more details). 1.5. EUT Exercise software The EUT exercise program used during radiated and conducted testing was designed to exercise the equipment under test in a manner similar to a typical use (Read tag ID): ASK polling V4.07d running under windows 2000 professionnel. 1.6. I/O cables - Standards power cord Length:0.8m (power supply of laptop) - LAN cable STP CAT 5e, length: 2m - 1x serial cable HP#24542G, shielded, length:2.8m Wurth N°742 701 17 on serial cable Text Nr 3408-FCC May 7th, 2005 page 4 /19 2. Radiated emission data 2.1. SET-UP The EUT is placed on a non-conducting table of 80cm height. A Tag type A is set on the EUT. Equipment configuration and running mode: - EUT is ON; - software is running; The installation of EUT is identical for pre-characterization measurement in a 3 meters full anechoic chamber and for measures on a 10 meters Open site. Text Nr 3408-FCC May 7th, 2005 page 5 /19 2.2. TEST EQUIPMENT Test Equipment up to 1GHz on 10 meters open site: Equipment Company Model Serial Spectrum Analyzer HP 8568B 2732A04140 Quasi-Peak adapter HP 85650A 2811A01136 RF Pre-selector HP 85685A 2833A00773 Biconical Antenna EMCO 3104C 9401-4636 Log Periodic Antenna EMCO 3146 2178 Spectrum Analyzer HP 8593E 3409u00537 Loop antenna Electro-metrics EM-6879 690234 Amplifier HP 8447F H64 3113A06394 EMCO-1050, 6 meters height antenna mast & EMCO-1060, 3 meters diameter Turntable. A 3 meters Open site located in SMEE Actions Mesures - Voiron (FRANCE). Pre-scan, test Equipment up to 1GHz: Equipment Company Model Serial EMC Analyzer HP 8591EM 3536A00384 Amplifier HP 8447F H64 3113A06394 Antenna (30MHz-1GHz) CHASE CBL6111A 1628 Loop antenna Electro-metrics EM-6879 690234 Text Nr 3408-FCC May 7th, 2005 page 6 /19 2.3. TEST SEQUENCE AND RESULTS 2.3.1.Pre-characterization at 3 meters from 30MHz to 1GHz A pre-scan of all the setup has been performed in a 3 meters full anechoic chamber. The distance between EUT and antenna is 3 meters. Test is performed in horizontal (H) and vertical (V) polarization, and on 4 faces of the EUT. See below for a graph example: Text Nr 3408-FCC May 7th, 2005 page 7 /19 2.3.2.Pre-characterization at 3 meters below 30MHz A pre-scan of all the setup has been performed in a 3 meters full anechoic chamber. The distance between EUT and antenna is 3 meters. Test is performed in horizontal (H) and vertical (V) axis and the loop antenna position was rotated during the test for maximized the emission measurement. See below for a graph example: Result below 30 MHz Text Nr 3408-FCC May 7th, 2005 page 8 /19 Text Nr 3408-FCC May 7th, 2005 page 9 /19 2.3.3.Characterization on 3 meters open site from 30MHz to 1GHz The product has been tested according to ANSI C63.4-(2003), FCC part 15 subpart C. Radiated Emission was measured on an open area test si…

Text truncated - open the document above for the full version.

FCC ID:QYELDB3-RDDE05078 1 RADIATED MEASUREMENT PHOTOS 1.1 Radiated emission Rear view Front view Detailed view FCC ID:QYELDB3-RDDE05078 1.2 Conducted emission Front view Rear view Detailed view